NEC Np1000 Lcd Projector Users Manual

							31
 Correcting Keystone Distortion
When the projector is not exactly perpendicular to the screen, keystone distortion occurs. To overcome it, you can use the
Keystone function, a digital technology that can adjust for keystone-type distortion, resulting in a crisp, square image.
The following procedure explains how to use the [Keystone] screen from the menu to correct trapezoidal distortions.
When the projector is placed diagonally to the screen,
When the projector is set up at an angle in relation to the screen, adjust the Horizontal option of the Keystone menu so
that the top and bottom of sides of the projected image are parallel.
1. Press the 3D REFORM button on the remote control or the projector
cabinet.
The Keystone screen will be displayed on the screen.
2. Press the SELECT 
 button to select [Vertical] and then use the
SELECT 
 or  so that the left and right sides of the projected im-
age are parallel.
* Adjust the vertical keystone distortion.
3. Align the left (or right) side of the screen with the left (or right) side
of the projected image.
•Use the shorter side of the projected image as the base.
•In the right example, use the left side as the base.
4. Press the SELECT 

 button to select [Horizontal] and then use the
SELECT 
 or  so that the top and bottom sides of the projected
image are parallel.
•Adjust the horizontal keystone distortion.
3. Projecting an Image (Basic Operation)
Screen frameProjected area
Align left side 
						

							32
NOTE:
•If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
•When doing Step 2, adjust the position of image so that the screen is smaller than the area of the projected area.
•To reset the 3D Reform correction setting values, press and hold the 3D REFORM button for a minimum of 2 seconds.
•Each time the 3D REFORM button is pressed, the item will change as follows: Keystone 
→ Cornerstone → None → Keystone →
...
For information on [Cornerstone], see Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) on page 41.
•The Cornerstone adjustment will not be available during the Keystone adjustment. To perform the Cornerstone adjustment, press
and hold the 3D REFORM button for a minimum of 2 seconds to reset the Keystone correction setting values. The Keystone
adjustment will not be available during the Cornerstone adjustment. To perform the Keystone adjustment, press and hold the 3D
REFORM button for a minimum of 2 seconds to reset the Cornerstone correction setting values.
•The 3D Reform feature can cause an image to be slightly blurred because the correction is made electronically.
3. Projecting an Image (Basic Operation)
5. Repeat steps 2 and 4 to correct keystone distortion.
6. After completing Keystone correction, press the ENTER button.
The Keystone screen will disappear.
•  To perform Keystone correction again, press the 3D REFORM button to
display the Keystone screen and repeat above steps 1 to 6. 
						

							33
3. Projecting an Image (Basic Operation)
 Optimizing an RGB Image Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
[Normal picture]
Sound level from the speaker and the AUDIO OUT
jack (Stereo mini) on the projector can be adjusted.
NOTE:
•Volume control is not available with the SELECT 
 or
 button when an image is enlarged by using the MAG-
NIFY (+) button or when the menu is displayed.
•The sound level is set to 20 at the factory.
NOTE:
•Some signals may take time to display or may not be displayed correctly.
•The Auto Adjust function does not work for component, video signals.
•If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. (→ page 75)
 Adjusting Volume Up & Down
SOURCE 3D REFORM
SELECT
AUTO ADJUST
SELECTPC CARDLAMPSTATUSPOWERON/STAND BY
SOURCE AUTO ADJUST
3D REFORM
AUTO ADJ.
LASER
3D REFORM
ASPECT
HELPPICTUREPIC-MUTE
LAMP MODE
R-CLICK L-CLICK
MOUSE
FREEZE
VOLUME MAGNIFYPAGE
UP
DOWN
NTEREXIT
VOLUME
LASER
3D REFORM
AUTO ADJ.ASPECT
HELPPICTUREPIC-MUTE
LAMP MODE
R-CLICK L-CLICK
MOUSE
FREEZE
MAGNIFYPAGE
UP
DOWN
NTEREXIT
Increase volume
Decrease volume 
						

							34
3. Projecting an Image (Basic Operation)
 Using the Laser Pointer
You can use the laser to draw your audiences attention to a red dot that you can place on any object.
CAUTION:
• Do not look into the laser pointer while it is on.
• Do not point the laser beam at a person.
• Do not allow children to use the laser pointer.
Press and hold the LASER button to activate the laser pointer.
LASERLASER
P
C
 
C
A
R
DL
A
M
PS
T
A
T
U
SP
O
W
E
RO
N
/
S
T
A
N
D
 
B
YSOURCE AUTO ADJUST
3D REFORMS
E
L
E
C
TP
C
 
C
A
R
D
L
A
M
P
S
T
A
T
U
S
P
O
W
E
RO
N
/
S
T
A
N
D
 
B
YSOURCE AUTO ADJUST
3D REFORM
Setting the function switch
There are two switches on the bottom of the battery case: an applicable projector selector switch (1) and laser enable/
disable switch (2). Check the projector being used and decide whether to enable or disable laser, then set these
switches as necessary using the tip of a thin ball-point pen. On this model, an applicable projector selector switch (1)
is not used.
ON OFF
Switch (2)
On ......................... Enabled (the laser lights when the LASER button is pressed) [Factory default]
Off ......................... Disabled (the laser does not light even when the LASER button is pressed)
Disable the laser when using in an environment in which the unit is accessible to children. 
						

							35
OFF
VIDEO
S-VIDEOVIEWER
LAN COMPUTER
COMPONENT
ON
SELECT
POWERPOWER
MENU
ENTEREXIT
3 1
2
	 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
1. Press the POWER (ON/STAND BY) button on the projector
cabinet or the POWER OFF button on the remote control. The
[Power Off / Are you sure?] message will appear.
2. Press the ENTER button
After the projector turns off, the cooling fans keep operating for a
while (Cooling-off time).
The cooling fans stop operating when the projector turns off and
goes into standby mode.
When in standby mode, the POWER indicator will light orange
and the STATUS indicator will light green.
3. After making sure that the projector is in standby mode, turn
off the Main Power switch. The power indicator will go out.
About Direct Power Off
The projector has a feature called Direct Power Off. This fea-
ture allows the projector to be turned off (even when projecting
an image) using a power strip equipped with a switch and a
breaker.
NOTE: Before using Direct Power Off, be sure to allow at least 20 min-
utes immediately after turning on the projector and starting to display an
image.
CAUTION
•Do not unplug the power cable from the wall outlet or projector
when the projector is powered on. Doing so can cause dam-
age to the AC IN connector of the projector and (or) the prong
plug of the power cable. To turn off the AC power supply when
the projector is powered on, use a power strip equipped with a
switch and a breaker.
•Do not turn off the AC power supply within 10 seconds of mak-
ing adjustment or setting changes and closing the menu.
Doing so can cause loss of adjustments and settings and re-
turn to default.
TIP: The projector can be unplugged during its cool down period after it is turned off.

 After Use
Preparation: Make sure that the main power is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
OFF
VIDEO
S-VIDEOVIEWER
LAN COMPUTER
COMPONENT
ON
SELECT
POWERPOWER
MENU
ENTEREXIT
3 1
2
PC CARDLAMPSTATUSPOWERON/STAND BY
SOURCE AUTO ADJUST
3D REFORM
PC CARDLAMPSTATUSPOWERON/STAND BY
SOURCE AUTO ADJUST
3D REFORM
P
C
 
C
A
R
DL
A
M
PS
T
A
T
U
SP
O
W
E
RO
N
/
S
T
A
N
D
 
B
YS
OU
RCE AUTO ADJUS
T
3D R
EFORM
SELECT
P
C
 
C
A
R
D
L
A
M
P
S
T
A
T
U
S
P
O
W
E
RO
N
/
S
T
A
N
D
 
B
YS
OU
RCE AUTO ADJUS
T
3D R
EFORM
L
E
N
S
 
S
H
I
F
T
L
E
F
TR
I
G
H
TD
O
W
NUP 
						

							36
FREEZE
3D REFORM
AUTO ADJ.ASPECT
HELPPICTUREPIC-MUTE
LAMP MODE
R-CLICK L-CLICKMOUSE
VOLUME MAGNIFYPAGE
UP
DOWN
PIC-MUTE3D REFORM
AUTO ADJ.ASPECT
HELPPICTURE
LAMP MODEFREEZE
VOLUME MAGNIFYPAGE
UP
DOWN
4. Convenient Features
 Turning Off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short period of time.
Press again to restore the image and sound.
TIP: Even though the image is turned off, the menu still remains on the screen.
 Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume motion.
TIP: The image is frozen but the original video is still playing back.
MAGNIFY
3D REFORM
AUTO ADJ.ASPECT
HELPPICTUREPIC-MUTE
LAMP MODEFREEZE
VOLUMEPAGE
UP
DOWN
 Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To  do so:
OFF
VIDEO
S-VIDEOVIEWER
LAN COMPUTER
COMPONENT
ONPOWERPOWER
MENU
ENTEREXIT
3 1
2
SELECT
MAGNIFY
3D REFORM
AUTO ADJ.ASPECT
HELPPICTUREPIC-MUTE
LAMP MODEFREEZE
VOLUMEPAGE
UP
DOWN
1. Press the MAGNIFY (+) button.
Each time the MAGNIFY (+) button is pressed,
the image is magnified.
* Image can be magnified up to 400%
2. Press the SELECT 

 button.
The area of the magnified image will be moved
3. Press the MAGNIFY (-) button.
Each time the MAGNIFY (-) button is pressed, the
image is reduced.
 Changing Lamp Mode
The lamp life can be extended by using the Eco mode.
To change to the [Eco] mode, do the following:
1. Press the LAMP MODE button to display [Lamp Mode] screen.
2. Use the SELECT 

 or  button to select [Eco] mode.
3. Press the ENTER button. Or press the SELECT 
 button to select [OK] and
press the ENTER button.
To cancel it, select [Cancel] and press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. Repeat Step 3.
LAMP MODE
LASER
3D REFORM
AUTO ADJ.ASPECT
HELPPICTUREPIC-MUTE
R-CLICK L-CLICK
MOUSE
FREEZE
VOLUME MAGNIFYPAGE
UP
DOWN
NTEREXIT
Lamp Mode Description Status of LAMP indicator
Normal Mode This is the Default setting
(100% Brightness).Off
Eco Mode
Select this mode to increase the lamp
life (approx. 80% Brightness (light output)
on NP2000 and approx. 85% Brightness 
(light output) on NP1000)Steady Green light 
						

							37
4. Convenient Features
OFF
VIDEO
S-VIDEOVIEWER
LAN COMPUTER
COMPONENT
ON
SELECT
POWERPOWER
MENU3 1
2
ENTEREXIT
 Getting Integrated Help
You get the contents about Help in English, German and
Japanese.
1. Press the HELP button on the remote control.
•When no menus appear, the How to Use Help
screen will be displayed.
•When menus appear, the screen will be displayed,
explaining the function of a highlighted item.
Display Help
Exit Help
HELP
LASER
3D REFORM
AUTO ADJ.ASPECT
PICTUREPIC-MUTE
LAMP MODE
R-CLICK L-CLICK
MOUSE
FREEZE
VOLUME MAGNIFYPAGE
UP
DOWN
NTEREXIT
2. Use the SELECT 
 or  button to scroll the viewing area.
3. Press the EXIT button.
•The Help will be closed. 
						

							38
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse cursor disappears.
NOTE: You can change the shape of the mouse cursor. To do so, select the menu → [Setup] → [Tools] → [Mouse] → [Mouse
Pointer].
Menu Display
Clicking with the left mouse button displays the menu.
To close the menu, click anywhere in the background.
Adjusting and Setting Display
You can select a menu item and click with the left mouse button to make adjustments and settings.
Using the middle button on the mouse
The projector supports the middle button on your mouse.
With the middle button you can do the following:
•You can use a scroll bar in the menu or the help.
•You can click the middle button to display or hide the ChalkBoard toolbar.
Example:
Click (or press and hold) the left mouse button on the  or  to adjust the brightness. Or click and drag the left
mouse button on the slide bar horizontally to adjust it.
To save the adjustments, click 
. The display is closed.
•Click    with the left mouse button to display a description of the selected menu item.
•Click and drag the title bar with the left mouse button to move the adjustment or setting dialog box.
4. Convenient Features
 Using a USB Mouse
Using a USB mouse gives you a smooth operation. A commercially
available USB mouse can be used.
NOTE: There may be some brands of a USB mouse that the projector does
not support.
NOTE: Do not try to insert the plug of your USB mouse into the LAN port
(LAN) of the projector.
Doing so can cause damage to the LAN port.
USB 
						

							39
4. Convenient Features

 Using the Optional Remote Mouse Receiver
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote con-
trol. It is a great convenience for your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
30° 30°
Remote mouse receiverComputer
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver
Remote sensor on the remote mouse receiver 7m/22 feet
When connecting using the USB port
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000 or MacOS X 10.0.0 or later
operating system.
* NOTE: In SP1 or older verison of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not
identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals. 
						

							40
4. Convenient Features
Operating your computer’s mouse from the remote control
You can operate your computers mouse from the remote control.
PAGE UP/DOWN Button ................. scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
on your computer.
SELECT 
 Button ................. moves the mouse cursor on your computer.
MOUSE L-CLICK Button ................. works as the mouse left button.
MOUSE R-CLICK Button ................. works as the mouse right button.
NOTE: When you operate the computer using the SELECT 
 button with the menu displayed, both the menu and the mouse
pointer will be affected. Close the menu and perform the mouse operation.
About Drag Mode:
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and the
drag operation can be performed simply by pressing the SELECT 
 button. To drop the item, press the MOUSE
L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.