NEC Neax2000 Ivs Command Manual

CHAPTER 2 ND-45669 (E)
Pag e 6
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
2.1.2 CAT Mode Setting Procedure
2.1.3 Notice on the CAT Mode
(1) CAT mode is used in on-line mode. Therefore, system data clear commands (CM00, CM01) cannot be
accessed from the CAT.
(2) To use the CAT after clearing all system data, perform the following operations on the system:
(a) Plug a PN-2DLCB/4DLCA card into the LT00 slot of PIM0.
(b) Connect the CAT (Multiline Terminal) to LEN0000 at the MDF.
(c) Set SW3 on the MP card...

ND-45669 (E) CHAPTER 2
Page 7
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
2.2 CAT Operation
When setting the office data, it is necessary to enter the following three kinds of data:
• Command Code
• First Data
• Second Data
An explanation of the data entry procedure follows:
(a) Operation for confirming the existing office data
With the above entry completed, the present second data is displayed on the LCD.
If the second data is not assigned yet, either the initial data value or “NONE” is displayed....

CHAPTER 2  ND -4 5669 ( E)
IN FORM ATIO N FO R  DATA P RO GRAMM ING
_
STC O M MAND  = _
CO M MAND  = 10 _
DE10> _
10> 0000_
DE10> 0000 : NONE -_
10> 0000 : NONE -300
EXEOK _
DE10> 0000 : 3 00 -_
S10> 0001 : NONE__
10> 0001 : NONE -301
EXEOK _
DE10> 001 : 301 _
DE 

ND -4 5669 ( E)  CHAPTER 2
IN FORM ATION  FO R  DATA  PR O GRAMM ING
DECE
DE10> _
10> 0001_
DE10> 0001 : NONE -__
CE10> _
10> 0000_
DE10> 0000 : NONE__
¬
10> 0001 : NONE -302
¬10> 0001 : NONE -30__
10> 0001 : NONE -301__
STC O M MAND  = _
CO M MAND  = 10 _
DE10> _
10> 0000
DE10> 0000 : 3 00-
10> 0000 : 3 00 -C C C
EXEOK 
DE10> 0000 : NONE 

CHAPTER 2  ND -4 5669 ( E)
IN FORM ATIO N FO R  DATA P RO GRAMM ING 

ND -4 5669 ( E)  CHAPTER 2
IN FORM ATION  FO R  DATA  PR O GRAMM ING 

CHAPTER 2  ND -4 5669 ( E)
IN FORM ATIO N FO R  DATA P RO GRAMM ING 

ND -4 5669 ( E)  CHAPTER 2
IN FORM ATION  FO R  DATA  PR O GRAMM ING 

CHAPTER 2  ND -4 5669 ( E)
IN FORM ATIO N FO R  DATA P RO GRAMM ING 

ND-45669 (E) CHAPTER 2
Page 15
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
Table 2-6  List of Commands for Each Business Feature
For Business SystemF:  First Data
S :  Second Data
— :  No Data
FEATURECOMMAND
1S T DATA/2N D DATA
(F/S)REMARKS
CODE Y-YYY
Account Code 08 – 362/S
12 02 F/S
15 30 F/1
20 0 – 3 F/085
42 – 10/S
90 00 F/F0085
Add-On Module 10 – F/S
12 05 F/0
30 18 F/0
41 1 09/S
90 00 – 03 F/S
98 0 F/S
Alarm Indications – – –
Alphanumeric Display 08 – 255/1
20 0 – 3 F/A10
35 03 F/S
77 0 – 3 F/S...