NEC Neax 2400 Ipx Wireless Features And Specifications

							NEAX2400 IPX Wireless Features and SpecificationsPage 46NDA-24313, Issue 1
C-155 Call Forwarding PS Incoming Call Incomplete
Service Conditions (cont’d)
9. The incoming incomplete call to a Dterm PS can be transferred to other Dterm PS’s, stations, Attendant
Consoles, Central Office and TIE lines when CALL FORWARDING PS INCOMING CALL
INCOMPLETE is in service.
10. The timer value of incoming incomplete call is approximately eight seconds, time duration until the
system recognizes that the D
term PS is Out of Zone from an incoming call attempt to the Dterm PS.
11. CALL FORWARDING PS INCOMING CALL INCOMPLETE is not activated in the case of the
incoming call from ISDN and the incoming call via the Attendant Console. The caller encounters
AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE or Busy Tone.
12. When a forwarded station for CALL FORWARDING PS INCOMING CALL INCOMPLETE sets CALL
FORWARDING - ALL CALLS to the announcement, CALL FORWARDING PS INCOMING CALL
INCOMPLETE is not activated but the caller hears Busy Tone.
13. In a FCCS network, every node must have one or more Announcement Trunk.
14. When incoming call comes from ISDN network, and the timer (T310) of the network side is expired, the
caller may hear the Announcement from network side.
15. In a FCCS network, CALL FORWARDING destination station must have a telephone number.
Note:CALL FORWARDING PS INCOMING CALL INCOMPLETE is cancelled by system initialization if the
data is not saved on the Hard Disk. 
						

							NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1Page 47
Dterm PSII Two Line Operation D-155
D-155 Dterm PSII Two Line Operation
General Description
This feature allows for the appearance of two lines on the line (L1 and L2) keys of the PS.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is available for Series 7300 or later software. 
2. Two kinds of lines can appear on the PS: My Line and Sub Line. These lines are associated with the
telephone numbers assigned to the port on the interface circuit.
L1 key: My Line
L 2   k e y : S u b  L i n e                                                                                                                                                                                                                                                                                                                    
3. When a PS becomes Out of Zone state while terminating to Sub Line, the call is disconnected by release
timer about one minute after.
4. When a PS user places a call on hold and presses the END key, the line lamp on the PS goes OFF. The PS
is recalled when the recall timer expires.
5. Voice Mail Indication (VMI) is not available for Sub Line.
6. When a PS is connected to a PS, Dual Hold is not available.
7. Blind Transfer to Sub Line is not available.
8. When one Line is connected, Blind Transfer to the other line is not available.
9. When transferring a call from a PS, the PS cannot place the third party on Hold.
The PS cannot activate Call Hold while connected with the station holding another call.
10. A PS cannot activate Call Hold when:
a.) Call Waiting is set to the PS
b.) the PS sets Call Waiting
c.) Call Waiting is set to the station connected with the PS
11. Call Waiting cannot be activated while the called PS is placed on Hold. 
						

							NEAX2400 IPX Wireless Features and SpecificationsPage 48NDA-24313, Issue 1
N-43 Name Display - Intra-Node Call
N-43  Name Display - Intra-Node Call
General Description
This feature allows a PS to indicate user information corresponding to the calling Physical Station Number while
engaged in a station-to-station call.
Operating Procedure
 When originating a station-to-station call:
LCD display of the calling station:
LCD display of the called station:
 When a station call has been transferred to another station by Call Forwarding - All Calls/Busy Line/Don’t 
Answer/PS - Incoming Incomplete:
LCD display of the calling station:
LCD display of the called station:
Service Conditions
1. This feature is available for Series 7300 or later software. 
2. User information corresponding to the Physical Station Number that can be displayed on the LCD is a
maximum of 16 digits.
3. User information is displayed on the LCD, indented to the left. The information may consist of English
alphabets, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of information can be displayed by key
operation (Refer to the User Guide for the PS).
5. This service and NAME DISPLAY by Open Application Interface cannot be activated concurrently.
6. This service and NAME DISPLAY service for D
terms can be activated concurrently.
7. Eight-digit display or 16-digit display is selectable by System Data, but cannot be used concurrently.
8. If the PS station has no name programmed for NAME DISPLAY - INTRA-NODE CALL service, the
Physical Station Number is displayed in the name field.
9. NAME DISPLAY - INTRA-NODE CALL is available for Station-to-Station Connection, Call
Forwarding - All Calls/Busy Line/Don’t Answer/PS - Incoming Incomplete, Call Waiting, and Call
Transfer.H. TARO
                      DIR                      SPD                       LNR
H. TARO
                      DIR                      SPD                       LNR
CF:         H. TARO
                      DIR                      SPD                       LNR
CF:         M. TARO
                      DIR                      SPD                       LNR 
						

							NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1Page 49
Name Display - Intra-Node Call - CCIS N-44
N-44  Name Display - Intra-Node Call - CCIS
General Description
Between CCIS nodes this feature allows the calling or called party information to be displayed on the LCD of a PS.
Operating Procedure
 When originating a call:
LCD display of the calling station:
LCD display of the called station:
 When a call has been transferred to another station by CALL FORWARDING - ALL CALLS/BUSY LINE/
DON’T ANSWER/PS - INCOMING INCOMPLETE:
LCD display of the calling station:
LCD display of the called station:
Service Conditions
1. This feature is available for Series 7300 or later software. 
2. User information corresponding to the Physical Station Number that can be displayed on the LCD is a
maximum of 16 digits.
3. User information is displayed on the LCD, indented to the left. The information may consist of upper case
letters, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of information can be displayed by key
operation (Refer to the User Guide of PS).
5. This service and NAME DISPLAY by Open Application Interface cannot be activated concurrently. 
6. This service and NAME DISPLAY service for D
terms can be activated concurrently.
7. Eight-digit display or 16-digit display is selectable by System Data, but cannot be used concurrently.
8. If the PS station has no name programmed for NAME DISPLAY - INTRA-NODE CALL - CCIS service,
“Office Code + Physical Station Number” is displayed in the name field.
9. NAME DISPLAY - INTRA-NODE CALL - CCIS is available for Tie Line Connection, Call Forwarding
- All Calls/Busy Line/Don’t Answer/PS - Incoming Incomplete, Call Waiting, and Call Transfer.H. TARO
                      DIR                      SPD                       LNR
H. TARO
                      DIR                      SPD                       LNR
H. TARO
                      DIR                      SPD                       LNR
CF:         M. TARO
                      DIR                      SPD                       LNR 
						

							NEAX2400 IPX Wireless Features and SpecificationsPage 50NDA-24313, Issue 1
N-45 Number Sharing
N-45 Number Sharing
General Description
This feature allows the Dterm user to use a PS as a Sub Station. In this feature, the Dterm and PS are referred as Main
Station and Sub Station, respectively. The main functions of this feature are as follows:
1. Call Forwarding - All Calls to PS - When the D
term (Main Station) user presses the feature key or dials the
access code, Call Forwarding - All Calls to PS (Sub Station) is set or cancelled. This function can also be
set or cancelled by dialing the access code from the PS (Sub Station).
2. D
term - Telephone Number Display - Even if a call is connected to the PS (Sub Station), the telephone
number of the Dterm (Main Station) is displayed on the other party’s LCD.
3. Billing Information - Even if a call is originated from the PS (Sub Station), billing information is recorded
as a call origination from the D
term (Main station).
4. Voice Mail Indication - Even if a call is transferred from the PS (Sub Station) to the Voice Mail System,
the voice mail is recorded on the mail box of the D
term (Main Station). The system controls Message
Waiting Indication on both the Dterm (Main Station) and PS (Sub Station).
Operating Procedure
To set from the Dterm
1. While in idle state, press the feature key for this feature. The PS Transfer lamp lights on the Dterm (Main
Station).
2. All the calls to the D
term (Main Station) are forwarded to the PS (Sub Station).
To cancel from the Dterm
1. While the Sub Station Transfer lamp lights, press the feature key for this feature. The PS Transfer lamp
goes off on the Dterm (Main Station).
2. This feature is cancelled.
To set from the PS
1. While in idle state, dial the access code for this feature and receive Service Set Tone. The PS Transfer
lamp lights on the Dterm (Main Station).
2. All the calls to the D
term are forwarded to the PS (Sub Station). 
To cancel from the PS
1. While this feature is set, dial the cancel code for this feature and receive Service Set Tone. The PS Transfer
lamp goes off on the Dterm (Main Station).
2. This feature is cancelled.
Service Conditions
1. This feature is available for Series 7300 or later software. 
2. A telephone number must be assigned to both Main and Sub Stations.
3. The PS cannot be assigned as Main Station.
4. Any combination of Main Station and Sub Station is available in a FCCS network.
5. The access code for an outgoing call cannot be assigned as a telephone number of the Sub Station.
6. Dialing the access code for this feature is available only for Main Station and Sub Station. Any other
station or trunk cannot set this feature.
7. The D
term user can set this feature using any line on the Dterm. Even if the Dterm user sets this feature using
a sub line, this feature is set to My Line.
8. The “PS Transfer” key is available only when the D
term is in idle state. 
						

							NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1Page 51
Number Sharing N-45
Service Conditions (cont’d)
9. When this feature is set while a call is terminating to Main Station, the call is not transferred to Sub Station.
In this case, this feature is available from the next call.
10. Message Waiting Lamp control by MEASSAGE REMINDER or CMWL command is applied only to the
called/designated station.
11. Even if this feature is set, recall to Main Station is not forwarded to Sub Station.
12. Forwarding operation of this feature is not counted in Multiple Call Forwarding features.
13. When a call is originated from Sub Station to OAI or MFC, the Sub Station number is sent.
Interactions
1. This feature takes precedence over the Call Forwarding, Do Not Disturb and Station Hunting features set
to Main Station.
2. When this feature is set, all the calls are forwarded to Sub Station even if CALL BLOCK [C-150] is set to
Main Station.
3. Off-Hook Line Number Display feature of the PS is independent of this feature.
4. MW indication for Sub Station is available for My Line of the D
term - PSII only.
5. When a Main Station is in a Station Hunting group, this feature can be activated only if the Main Station
is the pilot station. 
						

							NEAX2400 IPX Wireless Features and SpecificationsPage 52NDA-24313, Issue 1
V-24 Voice Mail Indication (VMI)
V-24 Voice Mail Indication (VMI)
General Description
This feature allows the system to notify a PS that a voice mail has been received.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is available for Series 7300 or later software. 
2. When a voice mail is received while the PS user is in conversation, the system notifies the PS after the
conversion ends.
3. When voice mails for multiple PS users are simultaneously received, each node can notify a maximum of
240 PSs. For the other PSs, notification is given at the time of PS Location Registration or end of call.
4. When a notification is given at the time of PS Location Registration or end of call, further notifications to
the same PS are not given unless the PS user accesses the voice mail system.
5. When a notification could not be terminated to a PS because of PS Out of Zone etc., the system notifies
again after four minutes.
6. This service and Open Application Interface (OAI) cannot be activated concurrently. 
						

							NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1Page 53
Wireless Analog Adjunct Connection W-8
W-8 Wireless Analog Adjunct Connection
General Description
This feature allows the existing PBX (no wireless function) to operate a PS as well  as a station  in the office. Each
PS is connected with the dedicated COT in the Built-in Wireless system. When a call is originated from the PS, it
terminates to the LC in the existing PBX via the corresponding COT and is handled by the existing PBX.
Operating Procedure
No manual operation is required.
Service Conditions
1. Only DTMF signals can be sent to the existing PBX.
2. Only one COT circuit card must be assigned for one PS.
3. When an incoming call terminates from the existing PBX to a PS via the LC → COT, if the terminating
PS is busy or out of zone, call termination is performed again.
Note:The calling party hears Ringback Tone without condition. While Ringback Tone is sent, the Built-in Wireless
System attempts the call termination to the called PS periodically and ring the PS when the PS becomes
available. 
4. The distinctive ringing service is not provided when a call terminates to the PS.
5. When the Speed Calling - System/Station service is activated using Overlap Dialing including the access
code, the number dialed may not be stored for redialing.
6. Whether or not Call Forwarding services (Call Forwarding - All Calls/Busy Line/Don’t Answer) by the
access code are available depends on the system data of the existing PBX. The Call Forwarding service
set by access code is activated only when the call terminates to the corresponding LC in the existing PBX.
7. The CALL FORWARDING PS INCOMING CALL INCOMPLETE [C-155] service cannot be set to a
PS.
8. When a call terminates from the existing PBX to the PS out of zone, the AUTOMATIC
ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] service cannot be activated. (The calling
party continues to hear Ringback Tone.)
9. When the PS engaged in a connection via the existing PBX moves Out of Zone, the AUTOMATIC
ANNOUNCEMNET - DISCONNECTED PS OUT OF ZONE [A-128] service is not provided. (The
calling party hears Reorder Tone.)
10. This feature is not available in the FCCS network.
Existing PBX (no wireless function) Built-in Wireless System
STN-A
STN-BLCCOT
ODTCSINT
LC
LCCOT COTZT
PS-A
PS-B StationC.O.
Line
TIE
Line 
						

							NEAX2400 IPX Wireless Features and SpecificationsPage 54NDA-24313, Issue 1
W-8 Wireless Analog Adjunct Connection
Service Conditions (cont’d)
11. When a call terminates to the PS using this feature, the calling number is not displayed on the PS.
12. The following PBX services are available for PS’s using this feature:
 C.O. call origination
 C.O. call termination
 Intra-office services
 Common, the other services
ISDN service
 Network service
 Call charging management service
 Maintenance administration service 
						

							NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1Page 55
ISDN Roaming I-41
I-41 ISDN Roaming
General Description
This feature allows PS to move to another PBX which has a different SYS-ID via Q.931a connection. The PBX
which PS can roam from/to is assigned Network Number (NWN). Network Number must be assigned as a unique
number for each network.
Operating Procedure
1. PS moves to another PBX which has a different SYS-ID.
2. PS registers its location automatically to the Home PBX at the Visitor PBX via Q.931a connection.
3. PS can originate a call from the Visitor PBX.
4. A call terminating to the PS is transferred from the Home PBX to the Visitor PBX via Q.931a connection.
Service Conditions
1. This feature is available for the Series 7300 software.
2. This feature is available between the PBXs which are connected via Q.931a.
3. PS in the Visitor PBX cannot move to another PBX via FCCS connection.
4. SMDR outputs the PS number instead of the account code when the PS is in the Visitor PBX.
5. In the Visitor PBX, PS cannot use supplementary services which need service access code. However,
TRANSFER, CALL HOLD and some ANNOUNCEMENT SERVICE are available.
6. If there is a TS between the Home PBX and Visitor PBX, the TS must also have the roaming feature.
7. CF - All Calls/Busy Line/PS Incoming Call Incomplete
a.) CF - All Calls - If PS assigns CF - All Calls at the Home PBX, all the terminating calls are
transferred. PS can also originate a call from the Visitor PBX.
b.) CF - Busy Line - If PS is busy in the Visitor PBX, the terminating call is transferred from the
Home PBX.
c.) CF - PS Incoming Call Incomplete - If call termination to PS is incomplete in the Visitor PBX,
the incoming call is transferred from the Home PBX.
8. In the Visitor PBX pseudo PS Physical Station Number (VISITOR PS PHYSICAL STATION NUMBER)
must be assigned by System Data. In addition, telephone number for visitor PS Physical Station Number
must be assigned.
Note:Visitor PS Physical Station Number must be the number which is not used in the Visitor PBX for the other
Physical Station Number.
9. The maximum number of PS’s includes the number of visitor PS Physical Station Numbers.
10. Roaming PS cannot use Two-Line feature.
11. Roaming PS cannot use Voice Mail Indication (VMI) feature.
12. Roaming PS cannot use OAI features.