NEC Neax 2400 Ipx Wireless Features And Specifications
Have a look at the manual NEC Neax 2400 Ipx Wireless Features And Specifications online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NEAX2400 IPX Wireless Features and SpecificationsPage 36NDA-24313, Issue 1 H-23 Handover H-23 Handover General Description When speech transmission quality becomes inferior, the Dterm PS re-originates a call automatically and seizes another radio channel, making the PBX hand the call over to another zone transceiver to maintain speech quality. Operating Procedure No manual operation is required. The Dterm PS series automatically sends HANDOVER request to the PBX. Service Conditions 1. This service is activated when the Dterm PS is engaged in communication. 2. The communication may be interrupted when the PBX hands the call over. The interruption is usually within a second, to a maximum of ten seconds. 3. This service is also available when a D term PS user moves to the far end of the radio zone and encounters inferior transmission quality. In this case, the Dterm PS searches for the radio zone with the stronger electric field, and if the radio zone is found, HANDOVER is activated and the conversation is continued in that zone. If there is no idle channel in the new radio zone, the conversation is continued in the current zone until the communication becomes unavailable, and AUTOMATIC RELEASE - OUT OF CELL CALLS is activated. 4. PS AUTHENTICATION is activated every time this service is activated. 5. In a FCCS network, inter-node HANDOVER is available within the identical PCN.
NEAX2400 IPX Wireless Features and Specifications NDA-24313, Issue 1Page 37 DTMF Signal Sender D-154 D-154 DTMF Signal Sender General Description This service allows the Dterm PS series user to send the PB signal (tone) to the called party (terminal, voice mail system, etc.) while engaged in communication. Operating Procedure To send the DTMF signal 1. Press a key while engaged in communication. The PBX automatically sends the corresponding signal tone to the called party. Service Conditions 1. When the DTMF signal is sent, there may be an interruption in communication. 2. The DTMF signal tone varies between 64 ms to 72 ms. 3. When this service is activated, the number pressed is displayed on the LCD (clearing the called party number previously displayed). The LCD display is cleared after 20 seconds, but the called party number will not be displayed again.
NEAX2400 IPX Wireless Features and SpecificationsPage 38NDA-24313, Issue 1 C-156 Consultation Hold C-156 Consultation Hold General Description This service allows the Dterm PS user to place a call on hold. Only that Dterm PS user can retrieve the held call. Operating Procedure To place a call on hold 1. While engaged in a call, press the TRF or F2 key; receive Special Dial Tone. The called number displayed on the LCD while engaged in a call will go out when the TRF or F2 key is pressed. The called party hears music via the external source. 2. To retrieve the call, press the TRF or F2 key again. The called party number will not be displayed on the LCD again. Service Conditions 1. When the Dterm PS user presses the END key while holding the call without dialing any key, the held party receives Reorder Tone and the connection is released. If the Dterm PS user has dialed one or more keys before pressing the END key while holding the call, the user is called back.
NEAX2400 IPX Wireless Features and Specifications NDA-24313, Issue 1Page 39 Flexible PS Numbering F-34 F-34 Flexible PS Numbering General Description Each Dterm PS series is assigned an unique number. Operating Procedure No manual operation is required. The data is entered via the maintenance administration terminal. Service Conditions 1. A maximum of nine digits can be assigned for a Dterm PS number, including # and *. The Dterm PS numbers must be assigned in uniform number of digits.
NEAX2400 IPX Wireless Features and SpecificationsPage 40NDA-24313, Issue 1 P-64 PS Service Class P-64 PS Service Class P-65 PS Restriction Class General Description This service permits all the Dterm PS series to be assigned a class of service in accordance with the degree of the system use desired. Operating Procedure No manual operation is required. Service Conditions 1. The route service class is assigned to determine the accessibility to the following service features. ANNOUNCEMENT - DONT ANSWER ANNOUNCEMENT - PS OUT OF CELL CALL FORWARDING - DONT ANSWER CALL FORWARDING - PS OUT OF CELL CENTREX COMPATIBILITY 2. Each D term PS is assigned a service feature class to determine which of the following service features the Dterm PS will be permitted to activate. CALL TRANSFER CALL WAITING - TERMINATING CENTREX COMPATIBILITY ANNOUNCEMENT SERVICE ANNOUNCEMENT - DONT ANSWER/CALL FORWARDING - DONT ANSWER ANNOUNCEMENT - PS OUT OF CELL/CALL FORWARDING - PS OUT OF CELL TRUNK LINE APPEARANCE a.) ANNOUNCEMENT SERVICE /ANNOUNCEMENT - DONT ANSWER/CALL FORWARDING - DONT ANSWER/ANNOUNCEMENT - PS OUT OF CELL/ ANNOUNCEMENT - DONT ANSWER - When the restricted D term PS user dials the service access code, the user receives Reorder Tone. If the CALL FORWARDING - INTERCEPT/ ANNOUNCEMENT service is set, the announcement notifying the user that an invalid number was reached will be sent. b.) CALL TRANSFER - When a restricted D term PS attempts Call Transfer (pressing of the TRF/ FLASH key), the operation will be ignored. c.) CALL WAITING - TERMINATING - When Call Waiting is attempted to the restricted D term PS which is busy, the calling party receives Reorder Tone. d.) CENTREX COMPATIBILITY - The switch hook flash operation will be invalid. e.) TRUNK LINE APPEARANCE - When the restricted D term PS user attempts to originate a call via the TRUNK LINE APPEARANCE service, the user receives Reorder Tone. 3. Each D term PS is assigned a service restriction class linking to that of the PBX to restrict the user from placing CO outgoing calls, etc. There are 15 classes and these classes are assigned in the system parameters (traveling class mark). Refer to DIRECT OUTWARD DIALING RESTRICTION (3-9) for more details.
NEAX2400 IPX Wireless Features and Specifications NDA-24313, Issue 1Page 41 PS-to-Station Calling P-66 P-66 PS-to-Station Calling General Description This service allows the Dterm PS series user to place a call to a PBX station, and vice versa. Operating Procedure To place a call using OVERLAP DIALING 1. Press the SEND or L1 key; receive Dial Tone. 2. Dial the desired number; receive Ringback Tone. To place a call using PRESET DIALING 1. Dial the desired number, then press the SEND L1 key; receive Ringback Tone. Service Conditions 1. The dialed digits are sent out in the following timing: a.) when the NEAX2400 IPX recognizes the last digit according to the numbering plan b.) if the NEAX2400 IPX cannot recognize the last digit, ten seconds after the last digit is dialed (inter-digit timer time-out).
NEAX2400 IPX Wireless Features and SpecificationsPage 42NDA-24313, Issue 1 S-131 Stack Dialing - Station S-131 Stack Dialing - Station General Description This service allows the Dterm PS series user to store the last five numbers dialed and to redial the numbers by pressing the REDIAL/PAUSE or F3 key. Operating Procedure To store the number 1. Using either OVERLAP DIALING or PRESET DIALING, dial the desired number. The number dialed is stored automatically. To redial the stored number using OVERLAP DIALING 1. Press the SEND or L1 key, then REDIAL/PAUSE or F3 key; the newest stored number is displayed on the LCD digit by digit, moving from right to left. The displayed number is dialed automatically. To redial the stored number using PRESET DIALING 1. Press the REDIAL/PAUSE or F3 key; the stored number is displayed on the LCD digit by digit, moving from right to left. By pressing the REDIAL/PAUSE or F3 key repeatedly, the second and the third numbers will be displayed successively. 2. When the desired number is displayed, press the SEND or L1 key. The number is dialed automatically. Service Conditions 1. A maximum of 40 digits (the numbers 0 to 9, #, *, and the function keys) can be stored. 2. The numbers are stored in the memory in the order they are dialed. If the number identical to the one in the memory is dialed, that number is recognized as the newest number, and the one already stored will be erased. (Regardless of the number of times the same number is dialed, it is stored only once.)
NEAX2400 IPX Wireless Features and Specifications NDA-24313, Issue 1Page 43 Speed Calling - Station S-132 S-132 Speed Calling - Station General Description This service allows the Dterm PS series user to dial certain frequently called numbers using 2-digit abbreviated call codes. Operating Procedure The Speed Calling data is set via the user definable data assignment. For detailed operation, refer to the Dterm PS User Guide. Service Conditions 1. Each abbreviated call code can store a maximum of 40 digits (the numbers 0 to 9, #, *, and the function keys). 2. A maximum of 20 call codes can be assigned. 3. If PRESET DIALING, when a wrong number is dialed, it can be cleared by the CLR or CLEAR key.
NEAX2400 IPX Wireless Features and SpecificationsPage 44NDA-24313, Issue 1 A-128 Automatic Announcement - Disconnected PS Out Of Zone A-128 Automatic Announcement - Disconnected PS Out Of Zone General Description When a talking Dterm PS series user moves Out of Zone, that is, the Wireless service area, to have the progressing call disconnected, the counterpart hears the announcement that the talks are disconnected due to the talking party moving Out of Zone. This also can apply when the power of either D term PS is OFF. Operating Procedure No manual operation is required. Service Conditions 1. This service is valid only in a two-party call. This service cannot be used when a call is placed on hold or conference calling participated in by three-party or more is in progress. 2. DAT (Digital Announcement Trunk) circuit card can be used as an announcement trunk. 3. AUTOMATIC ANNOUNCMENT - DISCONNECTED PS OUT OF ZONE is not applied to the cases where calls are in progress via a COT line or Attendant Console. A C.O. line subscriber hears Reorder Tone and a caller via the Attendant Console encounters Busy Tone. 4. In a FCCS network, every node must have one or more announcement trunk(s).
NEAX2400 IPX Wireless Features and Specifications NDA-24313, Issue 1Page 45 Automatic Announcement - Called PS Out of Zone A-129 A-129 Automatic Announcement - Called PS Out of Zone C-155 Call Forwarding PS Incoming Call Incomplete General Description When a call cannot be terminated due to the called Dterm PS series which is Out of ZT or whose power is OFF, the system automatically answers the call and provides an announcement to notify the calling party that the called Dterm PS is Out of Zone or if the CALL FORWARDING PS INCOMING CALL INCOMPLETE is set to a given destination, the aborted call can be transferred to the pre programmed station or Dterm PS. Operating Procedure No manual operation is required. Service Conditions 1. CALL FORWARDING PS INCOMING CALL INCOMPLETE can be programmed and cancelled by the Dterm PS with pressing Access Code + transferred telephone number. Note 2. In the case where the Dterm PS is Out of Zone, or its power is OFF, and the call is an incoming call from the Central Office directly or the Central Office call via the Attendant Console, the caller does not hear AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE, and hears the following tones. DIT: Ringback Tone is heard REMOTE ACCESS TO SYSTEM: Busy Tone is heard AUTOMATED ATTENDANT: Busy Tone is heard ATTENDANT CONSOLE: Busy Tone is heard ISDN - DID ADDRESSING: Announcement of ISDN (PSTN) is heard. 3. One system is given one kind of recorded message for AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE. 4. On the condition that both AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE and CALL FORWARDING PS INCOMING CALL INCOMPLETE are assigned to a D term PS, priority is given to CALL FORWARDING PS INCOMING CALL INCOMPLETE. 5. If an incoming call terminated at the very moment when a D term PS series user is setting CALL FORWARDING PS INCOMING CALL INCOMPLETE with a Pre-Set Dialing (before OFF-HOOK), the procedure so far becomes invalid. 6. If the another transfer service is set to the target destination party of CALL FORWARDING PS INCOMING CALL INCOMPLETE, the call is transferred to the last end party. 7. When a call is transferred to another D term PS activated by CALL FORWARDING PS INCOMING CALL INCOMPLETE and when the call termination is not completed, the call can be transferred to another destination party if the CALL FORWARDING PS INCOMING CALL INCOMPLETE is set. If the AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE is assigned, the caller hears the announcement. When both CALL FORWARDING PS INCOMING CALL INCOMPLETE and AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE are not programmed, the caller hears Busy Tone. 8. AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE does not allow the incoming call from outside to be connected to announcement trunk. The calling party hears Ringback Tone.