NEC Neax 2400 Ipx Circuit Card System Manual

							CHAPTER 3 NDA-24318
Page 44
Issue 1
OFFICE DATA PROGRAMMING
This figure represent example data when ASPC and AETH commands are required for an identical FPC
at the tandem node.
Figure 3-17   FCCS Networking via IP [F-36] and FCH FCCS Networking (both ASPC and AETH commands) 
Example Data Sheet 3
Note:
Provided that both FCCS Networking via IP and FCH FCCS Networking are configured, it depends on the
setting of the P_ROUTE parameter, which routing takes precedence. To take priority for FCCS
Networking via IP routing, assign data “1” to the P_ROUTE parameter.
NEAX2400 IPX
  FPC 1
 
POWERRouter
   Intranet
 
 IPTRK
 FCH
 DTI
C_RT: 50
FCHN: 1
NEAX2400 IPX
  FPC 2
PO WE RRouter IPTRK
 FCH
 DTI
C_RT: 70
FCHN: 3 FCH
 DTI
C_RT: 60
FCHN: 2
T
an
d
em
 
No
d
e
NEAX2400 IPX
  FPC 3
PO WE RRouter IPTRK
 FCH
 DTI
C_RT: 80
FCHN: 4
C_RT: 200
IP Address: 10.40.223.20
FCHN: 30
Example Routing Information Assignment by AFPC and AETH:
AFPC:
FPC 1: FPC=2, FCCH=1, P_ROUTE=0/1, C_RT=50, FCHN=1
FPC=3, FCCH=1, P_ROUTE=0/1, C_RT=50, FCHN=1
FPC 2: FPC=1, FCCH=1, P_ROUTE=0/1, C_RT=60, FCHN=2
FPC=3, FCCH=1, P_ROUTE=0/1, C_RT=70, FCHN=3
FPC 3: FPC=1, FCCH=1, P_ROUTE=0/1, C_RT=80, FCHN=4
FPC=2, FCCH=1, P_ROUTE=0/1, C_RT=80, FCHN=4
AETH:
FPC 1: FPC=2, FCHN=10, C_RT=100, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20
FPC=3, FCHN=10, C_RT=100, DST_IP=10.40.223.20, NEXT_IP=10.40.223.20
FPC 2: FPC=1, FCHN=20, C_RT=150, DST_IP=10.40.221.20, NEXT_IP=10.40.221.20
FPC=3, FCHN=20, C_RT=150, DST_IP=10.40.223.20, NEXT_IP=10.40.223.20
FPC 3: FPC=1, FCHN=30, C_RT=200, DST_IP=10.40.221.20, NEXT_IP=10.40.221.20
FPC=2, FCHN=30, C_RT=200, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20C_RT: 100
IP Address: 10.40.221.20
FCHN: 10C_RT: 150
IP Address: 10.40.222.20
FCHN: 20 
						

							NDA-24318 CHAPTER 3
Page 45
Issue 1
OFFICE DATA PROGRAMMING
This figure represent example data when FCCS routing data is not assigned by using the AFPC
command. Be sure to assign the following dummy data when using this configuration.
Figure 3-18   FCCS Networking via IP [F-36] - FCCS Network via IP Tandem Connection
(AFPC Dummy Data) Example Data Sheet 4
Note:
Be sure to assign dummy data.
PO WERRouter
NEAX2400 IPX
  FPC 2
 
 IPTRKTa
n
de
m
 N
o
de
C_RT: 150
IP Address: 10.40.222.20
FCHN: 20
PO WE RRouter IPTRK
C_RT: 151
IP Address: 10.40.222.21
FCHN: 21
Use different FCHN for passing through the node
  Intranet
NEAX2400 IPX
  FPC 1
POWERRouter
NEAX2400 IPX
  FPC 3
PO WERRouter IPTRK 
 IPTRK
C_RT: 100
IP Address: 10.40.221.20
FCHN: 10C_RT: 200
IP Address: 10.40.223.20
FCHN: 30
Example Routing Information Assignment by AFPC and AETH:
AFPC:
FPC 1: None
FPC 2:FPC=1, FCCH=1, P_ROUTE=1, C_RT=150, FCHN=20 
NoteFPC=3, FCCH=1, P_ROUTE=1, C_RT=151, FCHN=21 Note
FPC 3: None
AETH:
FPC 1: FPC=2, FCHN=10, C_RT=100, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20
FPC=3, FCHN=10, C_RT=100, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20
FPC 2: FPC=1, FCHN=20, C_RT=150, DST_IP=10.40.221.20, NEXT_IP=10.40.221.20
FPC=3, FCHN=21, C_RT=151, DST_IP=10.40.223.20, NEXT_IP=10.40.223.20
FPC 3: FPC=1, FCHN=30, C_RT=200, DST_IP=10.40.222.21, NEXT_IP=10.40.222.21
FPC=2, FCHN=30, C_RT=200, DST_IP=10.40.222.21, NEXT_IP=10.40.222.21 
						

							CHAPTER 3 NDA-24318
Page 46
Issue 1
OFFICE DATA PROGRAMMING
This figure represent example data when AFPC and AETH commands are required for an identical FPC
at the tandem node.
Figure 3-19   FCCS Networking via IP [F-36] and FCH FCCS Networking (AFPC or AETH commands)
Example Data Sheet 5
Note:
Be sure to assign dummy data.
PO WERRouter IPTRK
 FCH
 DTI
C_RT: 70
FCHN: 3
C_RT: 150
IP Address: 10.40.222.20
FCHN: 20 NEAX2400 IPX
  FPC 2
Ta
n
de
m 
N
o
de
   Intranet
PO WE RRouter
NEAX2400 IPX
  FPC 1
 IPTRK
C_RT: 100
IP Address: 10.40.221.20
FCHN: 10
NEAX2400 IPX
  FPC 3
 FCH
 DTI
C_RT: 80
FCHN: 4
Example Routing Information Assignment by AFPC and AETH:
AFPC:
FPC 1: None
FPC 2:FPC=1, FCCH=1, P_ROUTE=1, C_RT=150, FCHN=20 
NoteFPC=3, FCCH=1, P_ROUTE=0, C_RT=70, FCHN=3
FPC 3: FPC=1, FCCH=1, P_ROUTE=0, C_RT=80, FCHN=4
FPC=2, FCCH=1, P_ROUTET=0, C_RT=80, FCHN=4
AETH:
FPC 1: FPC=2, FCHN=10, C_RT=100, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20
FPC=3, FCHN=10, C_RT=100, DST_IP=10.40.222.20, NEXT_IP=10.40.222.20
FPC 2: FPC=1, FCHN=20, C_RT=150, DST_IP=10.40.221.20, NEXT_IP=10.40.221.20
FPC=3, FCHN=3, C_RT=70, DST_IP=0.0.0.0, NEXT_IP=0.0.0.0 
NoteFPC 3: None 
						

							NDA-24318 CHAPTER 4
Page 47
Issue 1
OPERATION TESTS AFTER INSTALLATION
CHAPTER 4 OPERATION TESTS AFTER INSTALLATION
1. GENERAL
This chapter explains the procedure to verify the normal operation of the IPTRK circuit
card, when installation and necessary data setting have been completed. This chapter also
explains the procedures to test and correct possible IPTRK circuit card-related faults.
2. CCIS NETWORKING VIA IP [C-163]/VOICE OVER IP (H.323)
When using the H.323 Handler (PA-8IPTB-A) as a signaling interface for Voice over IP (H.323), perform the
following circuit card operation tests. If necessary, perform fault repairs.
Caution:Some LSIs on this circuit card may be hot. Handle with care.
1. Test of OPE lamp on IPTRK circuit card: 
Note
Note:
H.323 Handler (PA-8IPTB-A).
a.) See if the OPE lamp on the IPTRK circuit card 
Note is lighting green. This lamp lights if the
circuit card is operating normally.
Note:H.323 Handler (PA-8IPTB-A).
b.) When the OPE lamp is OFF, initialize the circuit card, or perform the insertion/extraction of the
circuit card once or twice. If the lamp still does not light, replace the circuit card.
Figure 4-1   Lamps to be Tested (CCIS Networking via IP [C-163])
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
SUBOPE3
SUBOPE2BUSY
L3
L2
L1
IP-TXRX
IP-100M
F-TXRX
F-100M F-LRR
F-LINK
F-COL
MODE
IPCON
FCON
MB
MBR
Not Used
Not Used
Not Used
Not Used
OPEIs IPTRK card
IP-LRR     Is IP network available 
for connection?
IP-LINK Is IPTRK-IP network link  
  physically established?
SUBOPE1Is appropriate data 
 assigned on GK?
IP-COL
IPTRK Circuit Card (H.323 Handler/
(H.323 Handler)
operating normally?
PA-8IPTB-A) 
						

							CHAPTER 4 NDA-24318
Page 48
Issue 1
OPERATION TESTS AFTER INSTALLATION
1. Test of IP-LINK lamp on IPTRK circuit card: Note
Note:
H.323 Handler (PA-8IPTB-A).
a.) See if the IP-LINK lamp on the IPTRK circuit card 
Note is lighting green.
This lamp will light if the circuit card is physically connected to the IP
network.
Note:H.323 Handler (PA-8IPTB-A).
b.) When the IP-LINK lamp is OFF, make sure that the Ethernet cable is securely
connected to the IPCON connector. Make sure that neither the Ethernet cable nor the router are
faulty. If necessary, replace the Ethernet cable.
2. Test of SUBOPE1 lamp on IPTRK circuit card 
Note:
Note:H.323 Handler (PA-8IPTB-A).
a.) See if the SUBOPE1 lamp on the IPTRK circuit card 
Note is lighting green. This lamp will light
when the appropriate data has been assigned on the Gate Keeper (GK) side.
Note:H.323 Handler (PA-8IPTB-A).
b.) When the SUBOPE1 lamp is OFF, make sure that the related office data is correctly assigned on
both the PBX side and the Gate Keeper (GK) side.
3. Test of IP-LRR lamp on IPTRK circuit card: 
Note
Note:
H.323 Handler (PA-8IPTB-A).
a.) See if the IP-LRR lamp on the IPTRK circuit card 
Note is lighting green. This lamp will light if
the IP network is available for connection establishment.
Note:H.323 Handler (PA-8IPTB-A).
b.) When the IP-LRR lamp is OFF, make sure that the related office data was correctly assigned.
Make sure that each IP address assigned on the AGIP command is correct.
4. Test of Speech Conditions with Distant Node:
a.) Perform the connection test to see if speech can be made with the counterparts of the connected
node.
b.) If any test result is abnormal, make sure that the related office data was assigned correctly.
5. Test of System Messages:
a.) When an IPTRK circuit card 
Note is installed, the following messages may be created:
Note:H.323 Handler (PA-8IPTB-A).
For CCIS Networking via IP [C-163]:
33-R IP CARD WARNING
33-S IP CARD FAILURE
33-T IP CARD RECOVERY
33-U H.323 INFORMATION NOTICE
b.) When any of the messages above are created, make sure that the Ethernet cable is securely
connected to the IPCON connector (on the IPTRK circuit card), or perform the continuity test of
the cable (voltage and resistance measurement), using a voltmeter. Otherwise, replace the IPTRK
circuit card or H.323 Handler.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							NDA-24318 CHAPTER 4
Page 49
Issue 1
OPERATION TESTS AFTER INSTALLATION
3. FCCS NETWORKING VIA IP [F-36]
When using the IPTRK circuit card for FCCS Networking via IP [F-36] (Point-to-
Multipoint Connection), perform the following circuit card operation tests. If necessary,
perform fault repairs.
Caution:Some LSIs on this circuit card may be hot. Handle with care.
1. Test of OPE lamp on IPTRK circuit card:
a.) See if the OPE lamp on the IPTRK circuit card is lighting green. This lamp will light if the circuit
card is operating normally.
b.) When the OPE lamp is OFF, initialize the circuit card, or perform the insertion/extraction of the
circuit card once or twice. If the lamp still does not light, replace the circuit card.
2. Test of SUBOPE0 and SUBOPE1 lamps on IPTRK circuit card:
a.) See if the SUBOPE0 and SUBOPE1 lamps on the IPTRK circuit card are lighting green. Note
that SUBOPE1 should light if the circuit card is furnished with an optional sub board (PZ-
8VCTB).
b.) When either (or both) of the lamps are OFF, initialize the circuit card, or perform the insertion/
extraction of the circuit card once or twice. Also, if a sub board is in use, make sure the daughter
board is securely attached to the IPTRK circuit card (main board). If the lamp still does not light,
replace the circuit card.
Figure 4-2   Lamps to be Tested (FCCS Networking via IP [F-36] [Point-to-Multipoint Connection])
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
SUBOPE3
SUBOPE2       BUSY
L3
L2
L1
IP-TXRX
IP-100M
F-TXRX
F-100M
F-COL
MODE
IPCON
FCON
MB
MBR
Not Used
Not Used
OPEIs IPTRK card operating  
         normally?
IP-LRR     Is IP network available 
for connection?
IP-LINKIs IPTRK-IP network link  
  physically established?
SUBOPE1Is CPU of sub board 
 operating normally?
L1Is FCCS network 
link established?
SUBOPE0     Is CPU of IPTRK card’s 
main board operating normally?
IP-COL
IPTRK Circuit CardSub Board (PZ-8VCTB)
F-LRRIs FCCS network available 
for connection?
F-LINKIs IPTRK-FCCS network 
link physically established? 
						

							CHAPTER 4 NDA-24318
Page 50
Issue 1
OPERATION TESTS AFTER INSTALLATION
3. Test of IP-LINK lamp on IPTRK circuit card:
a.) See if the IP-LINK lamp on the IPTRK circuit card is lighting green. This
lamp will light if the circuit card is physically connected to the IP network.
b.) When the IP-LINK lamp is OFF, make sure that the Ethernet cable is securely
connected to the IPCON connector. Make sure that neither the Ethernet cable
nor the router are faulty. If necessary, replace the Ethernet cable.
4. Test of L1 lamp on IPTRK circuit card:
a.) See if the L1 lamp on the IPTRK circuit card is lighting green. This lamp will light if the FCCS
network link is established.
b.) When the L1 lamp is OFF, make sure the office data was correctly assigned. If necessary, replace
the circuit card.
5. Test of IP-LRR lamp on IPTRK circuit card:
a.) See if the IP-LRR lamp on the IPTRK circuit card is lighting green. This lamp will light if the IP
network is available for connection establishment.
b.) When the IP-LRR lamp is OFF, make sure that the related office data is correctly assigned. Make
sure that each IP address assigned on the AGIP command is correct.
6. Test of F-LINK lamp on IPTRK circuit card:
a.) See if the F-LINK lamp on the IPTRK circuit card is lighting green. This lamp will light if the
circuit card is physically connected to the FCCS network. 
b.) When the F-LINK lamp is OFF, make sure that the Ethernet cable is securely connected to the
FCON connector. Make sure that neither the Ethernet cable nor the router are faulty. If necessary,
replace the Ethernet cable.
7. Test of F-LRR lamp on IPTRK circuit card:
a.) See if the F-LRR lamp on the IPTRK circuit card is lighting green. This lamp will light if the
FCCS network is available for connection establishment.
b.) When the F-LRR lamp is OFF, make sure that the related office data was assigned correctly.
Make sure that each IP address assigned on the AETH or AGIP command is correct.
8. Test of Speech Conditions with Distant Nodes:
a.) Perform the connection tests to see if speech can be made with the counterparts of the connected
nodes.
b.) If any test result is abnormal, make sure the related office data was assigned correctly.
9. Test of System Messages:
a.) When an IPTRK circuit card is installed, the following messages may be created:
23-S FCCS FAILURE
23-T FCCS FAILURE RECOVERED 
Note
b.) When any of the messages above are created, make sure that the Ethernet cable is securely
connected to the IPCON/FCON connector (on the IPTRK circuit card), or perform the continuity
test of the cable (voltage and resistance measurement), using a voltmeter.
Note:Although this message is issued soon after performing system/circuit card initialization, it does not
necessarily mean a result of fault information. In this case, the message generally indicates the placement
of the IPTRK circuit card in to normal operation mode.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required