NEC Multisync Lcd225wnx Users Manual

							MultiSync LCD205WNXM
MultiSync LCD225WNXM
MultiSync LCD225WNX
User’s Manual
 
						

							English
English-1
Declaration
Declaration of the Manufacturer
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
RISK OF ELECTRIC SHOCK • DO NOT OPEN
As an ENERGY STA R Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STA R
guidelines for energy efficiency. ENERGY STA R is a U.S. registered mark. The ENERGY STA R emblem does not represent EPA
endorsement of any product or service.
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,
Norway, Spain, Sweden, U.K..
Microsoft and Windows are registered trademarks of the Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
All other trademarks or registered trademarks are property of their respective owners.We hereby certify that the color monitors MultiSync
LCD205WNXM (L206T8)/MultiSync LCD225WNXM/
LCD225WNX (L226T9) are in compliance with
Council Directive 73/23/EEC:
– EN 60950-1
Council Directive 89/336/EEC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024and marked with
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
Plug Type North AmericaEuropean
ContinentalU.K. Chinese Japanese
Plug Shape
Country
VoltageU.S.A./Canada U.K. China JapanEU (except U.K.)
120* 230 220 100230
*When operating the MultiSync LCD205WNXM/LCD225WNXM/LCD225WNX monitor with its AC 125-240V power supply, use
a power supply cord that matches the power supply voltage of the AC power outlet being used.
NOTE:This product can only be serviced in the country where it was purchased.
 
						

							English-2
For the Customer to use in U.S.A. or Canada
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1.
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync LCD205WNXM (L206T8)/MultiSync LCD225WNXM/LCD225WNX
(L226T9) color monitor so as not to interfere with radio and television reception.
(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,
and meet the following condition.
Power supply cord Non shield type, 3-conductor
Length 2.0 m
Plug shape
U.S.A
(2) Please use the supplied shielded video signal cable and audio cable. Use of other cables and adapters may
cause interference with radio and television reception.
2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Blvd, Suite 1100
Itasca, Illinois 60143
Tel. No.: (630) 467-3000
Type of Product: Display Monitor
Equipment Classification: Class B Peripheral
Model: MultiSync LCD205WNXM (L206T8)/
MultiSync LCD225WNXM/LCD225WNX (L226T9)
We hereby declare that the equipment specified above conforms
to the technical standards as specified in the FCC Rules.
 
						

							English
English-3
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•MultiSync LCD monitor with tilt base
•Audio Cable
•Power Cord
•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
•Video Signal Cable (DVI-D to DVI-D) (LCD225WNX only)
•USB Cable (LCD205WNXM/LCD225WNXM only)
•User’s Manual
•Cable Management Cover
•CD-ROM
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2.For the PC or MAC with DVI digital output: Connect the DVI-D signal cable (not included for the U.S. and China) to the
connector of the display card in your system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your
system (Figure A.2). Tighten all screws.
For the MAC: Connect the MultiSync Macintosh cable adapter (not included) to the computer. Attach the 15-pin mini
D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure A.3). Tighten all screws.
NOTE:Some Macintosh systems do not require a Macintosh cable adapter.
User’s Manual Audio CablePower Cord*
2
15-pin mini D-SUB
male to 15-pin mini
D-SUB maleMultiSync LCD monitor
Figure A.1 Figure A.3
Macintosh
Cable Adapter
(not included)
Figure A.2
*Remember to save your original box and packing material to transport or ship the monitor.
*2 Type of power cord included will depend on the where the LCD monitor is to be shipped.
DVI-D to DVI-D
(LCD225WNX only)USB Cable
(LCD205WNXM/
LCD225WNXM only)
  User’s
ManualCable Management
Cover CD-ROM
 
						

							English-4
3.Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position (Figure B.1).
4. Connect all cables to the appropriate connector on the back of the monitor (Figure B.1). Using the USB cable, connect the
B type connector to the USB upstream port on the bottom of the monitor and A type connector to the downstream port on
the computer (Figure C.1). If you can use the cord from the USB device, use one of the downstream ports on the side or
bottom of the monitor. Connect Headphones (not included) to the appropriate connector at the rear side of the monitor, if
desired (Figure B.1).
Input2 (D-Sub)
USB
(LCD205WNXM/LCD225WNXM only) DVI Cable
Input1 (DVI) Highest
Stand
Position
Power cord30° Tilt
A Type
A TypeA Type
B Type
B Type
USB Device
Figure B.1Figure C.1
Figure C.2
Power cordDVI Cable
Figure C.3
NOTE:If connecting both DVI and D-Sub cables, the DVI cable must be connected along side the rib on the power cord
side (Figure C.2).
5. For successful cable management, place the cables in this order into the cable management: power cable and DVI cable.
6. Place DVI cable and power cable into the specific hooks as indicated in Figure C.3.
7.Place the D-Sub and the USB cables (LCD205WNXM/LCD225WNXM only) into the specific hooks indicated in Figure C.4.
8. Make sure all cables are resting flat against the stand (Figure C.4).
Figure C.4
D-Sub CableUSB Cable
(LCD205WNXM/
LCD225WNXM only)
Flat
Audio InputHeadphone
 
						

							English
English-5 9. Hold all the cables firmly and place the cable cover onto the stand (Figure D.1). To remove the cable cover, lift the cover
off as shown in Figure D.2.
NOTE:Handle with care when placing the cable cover and avoid pinching your fingers.
10. Connect the power cord to the power outlet (Figure D.3).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it,
as show in Figure E.1.
NOTE:Please refer to the Caution section of this manual for proper selection of power cord.
11.Turn on the monitor with the front power button and the computer (Figure D.3).
Figure E.1
12. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings (Analog input
only). For further adjustments, use the following OSD controls:
•Auto Contrast
•Auto Adjust
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.
NOTE:If you have any problem, please refer to the Troubleshooting section of this User’s Manual.
Figure D.1
Figure D.2 Figure D.3
Power button
Figure E.1
Screen Rotation
Before rotating, the screen must be raised to the highest level to
avoid knocking the screen on the desk or pinching with your
fingers.
To raise the screen, place hands on each side of the monitor and
lift up to the highest position (Figure RL.1).
To rotate screen, place hands on each side of the monitor screen
and turn clockwise from Landscape to Portrait or counter-
clockwise from Portrait to Landscape (Figure R.1).
Tilt and Swivel
Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired
(Figure TS.1).
NOTE:Handle with care when tilting and swivelling the monitor screen.
Figure RL.1
Figure TS.1
Raise and Lower Monitor Screen
The monitor may be raised or lowered. To raise or lower
screen, place hands on each side of the monitor and lift or
lower to the desired height (Figure RL.1).
NOTE:Handle with care when raising or lowering the
monitor screen.
Figure R.1
 
						

							English-6
Figure R.2
Non-abrasive surface
Figure R.3 Figure R.4
Connecting a Flexible Arm
This LCD monitor is designed for use with a flexible arm.
Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor
must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor.
The LCD monitor shall only be used with an approved arm (e.g. GS mark).
Tighten all screws
100 mm 100 mmThickness of Bracket
(Arm) 2.0 ~ 3.2 mm
4-SCREWS (M4)
MAX depth: 8.5 mm
If use other screw,
check lenght of screw.
Specifications
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Place hands on each side of the monitor and lift up to the highest position.  Remove the cable cover.
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it,
as shown in the figure beside.
2. Disconnect all cables.
3. Place monitor face down on a non-abrasive surface (Figure R.2).
4. Remove the 4 screws connecting the monitor to the stand and remove the stand (Figure R.3).
The monitor is now ready for mounting in an alternative manner.
5. Connect all cables to the back of the monitor (Figure R.4).
6. Reverse this process to re-attach stand.
NOTE:Use only VESA-compatible alternative mounting method.
NOTE:Handle with care in order to avoid damage or dropping the stand.
Weight of LCD assembly: 5.9 kg (MAX) (LCD205WNXM)
6.3 kg (MAX) (LCD225WNXM/
         LCD225WNX)
 
						

							English
English-7
Controls
OSD (On-Screen-Display) control buttons on the front of the monitor
function as follows:
1. Basic function at pressing each key
2. OSD structure
Showing OSD.Shortcut to Brightness
adjust Menu.
Button
At No OSD
showingShortcut to Volume adjust
Menu.Input signal select.
At OSD showing(Icon selection stage)Go to Adjustment stage. Cursor goes to left. Cursor goes to right.
At OSD showing(Adjustment stage)Go to Icon selection stage. Adjust value decrease or
Cursor for adjust goes to left.Adjust value increase or
Cursor for adjust goes to
right.Reset operation.
Mute off/on switch on Volume
adjustment Menu.
SELECT–+12 / RESET
Main Menu (Icon Select, Analog Input)
Sub Menu (Icon Select)Press
“SELECT”
keyPress
“SELECT”
key
Press
 “–” or “+”Main Menu (Adjust)
Sub Menu (Adjust)Press “SELECT” key
Press
“SELECT” keyAdjust by using
“–” or “+”
Adjust by using
“–” or “+”
Press
 “–” or “+” Example Tool:
Press “SELECT” key
Press
“SELECT” key
 
						

							English-8
VOLUME
Control the sound volume of speakers and headphone.
To mute the speaker sound, press the 12/RESET key.
BRIGHTNESSAdjusts the overall image and background screen brightness.
CONTRAST
Adjusts the image brightness in relation to the background.
AUTO CONTRAST (Analog Input only)
Adjusts the image displayed for non-standard video inputs.
AUTO ADJUST (Analog Input only)
Automatically adjusts the Image Position, the H. Size and Fine setting.
LEFT/RIGHT (Analog Input only)
Controls Horizontal Image Position within the display area of the LCD.
DOWN/UP (Analog Input only)
Controls Vertical Image Position within the display area of the LCD.
H. SIZE (Analog Input only)
Adjusts the horizontal size by increasing or decreasing this setting.
FINE (Analog Input only)
Improves focus, clarity and image stability by increasing or decreasing this setting.
COLOR CONTROL SYSTEMS
Five color presets (9300/7500/sRGB/USER/NATIVE) select the desired color setting.
The sRGB and NATIVE, color presets are standard and cannot be changed.
COLOR RED
Increase or decreases Red. The change will appear on screen.
COLOR GREEN
Increase or decreases Green. The change will appear on screen.
COLOR BLUE
Increase or decreases Blue. The change will appear on screen.
TOOL
Selecting TOOL allows you to get into the sub menu.
FACTORY PRESET
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings. The RESET button
will need to be held down for several seconds to take effect. Individual settings can be reset by highlighting the
control to be reset and pressing the RESET button.
EXIT
Selecting EXIT allows you exit OSD menu/ sub menu.
LANGUAGE
OSD control menus are available in nine languages.
OSD TURN OFF
The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how
long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are
10 - 120 seconds by 5 seconds step.
 
						

							English
English-9
OSD LOCK OUT
This control completely locks out access to all OSD control functions without Volume, Brightness and Contrast.
When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are
locked out. To activate the OSD Lock Out function, press “12/ RESET”, then “+” key and hold down
simultaneously. To de-activate the OSD Lock Out, press “12/ RESET”, then “+” key and hold down
simultaneously.
RESOLUTION NOTIFIER
If ON is selected, a message will appear on the screen after 45 seconds, notifying you that the resolution is not at
optimal resolution.
MONITOR INFO
Indicates the model and serial numbers of your monitor.
EXPANSION
Selects the zoom mode.
FULL: The image is expanded to 1680 x 1050, regardless of resolution.
ASPECT: The image is expanded without changing the aspect ratio.
DDC/CI
Turns ON or OFF the two way communication and control of the monitor.
INPUT RESOLUTION (Analog Input Only)
Sets of the resolution of input signal to one of the following:
When vertical active size is 768, you can select resolution from 1024 x 768, 1280 x 768, 1360 x 768.
When vertical active size is 1050, you can select resolution from 1400 x 1050, 1680 x 1050.
OSD Warning
OSD Warning menus disappear with SELECT button.
NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or
when there is a change of input signal or video is inactive, the No Signal window will appear.
RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power is
turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the
Resolution Notifier window will open. This function can be disabled in the TOOL menu.
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After
the power is turned on or there is a change of input signal or the video signal doesn’t have proper timing,
the Out Of Range menu will appear.