NEC Multisync Lcd225wnx Users Manual

MultiSync LCD205WNXM
MultiSync LCD225WNXM
MultiSync LCD225WNX
User’s Manual
 

English
English-1
Declaration
Declaration of the Manufacturer
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER...

English-2
For the Customer to use in U.S.A. or Canada
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1.
Ce produit porte la marque ‘C-UL’ et se...

English
English-3
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
•MultiSync LCD monitor with tilt base
•Audio Cable
•Power Cord
•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
•Video Signal Cable (DVI-D to DVI-D) (LCD225WNX only)
•USB Cable (LCD205WNXM/LCD225WNXM only)
•User’s Manual
•Cable Management Cover
•CD-ROM
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2.For...

English-4
3.Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position (Figure B.1).
4. Connect all cables to the appropriate connector on the back of the monitor (Figure B.1). Using the USB cable, connect the
B type connector to the USB upstream port on the bottom of the monitor and A type connector to the downstream port on
the computer (Figure C.1). If you can use the cord from the USB device, use one of the downstream ports on the side or
bottom...

English
English-5 9. Hold all the cables firmly and place the cable cover onto the stand (Figure D.1). To remove the cable cover, lift the cover
off as shown in Figure D.2.
NOTE:Handle with care when placing the cable cover and avoid pinching your fingers.
10. Connect the power cord to the power outlet (Figure D.3).
NOTE:If you have difficulty removing the cable cover, please push the lower opening upward to remove it,
as show in Figure E.1.
NOTE:Please refer to the Caution section of this manual for...

English-6
Figure R.2
Non-abrasive surface
Figure R.3 Figure R.4
Connecting a Flexible Arm
This LCD monitor is designed for use with a flexible arm.
Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor
must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor.
The LCD monitor shall only be used with an approved arm (e.g. GS mark).
Tighten all screws
100 mm 100 mmThickness of...

English
English-7
Controls
OSD (On-Screen-Display) control buttons on the front of the monitor
function as follows:
1. Basic function at pressing each key
2. OSD structure
Showing OSD.Shortcut to Brightness
adjust Menu.
Button
At No OSD
showingShortcut to Volume adjust
Menu.Input signal select.
At OSD showing(Icon selection stage)Go to Adjustment stage. Cursor goes to left. Cursor goes to right.
At OSD showing(Adjustment stage)Go to Icon selection stage. Adjust value decrease or
Cursor for adjust goes to...

English-8
VOLUME
Control the sound volume of speakers and headphone.
To mute the speaker sound, press the 12/RESET key.
BRIGHTNESSAdjusts the overall image and background screen brightness.
CONTRAST
Adjusts the image brightness in relation to the background.
AUTO CONTRAST (Analog Input only)
Adjusts the image displayed for non-standard video inputs.
AUTO ADJUST (Analog Input only)
Automatically adjusts the Image Position, the H. Size and Fine setting.
LEFT/RIGHT (Analog Input only)
Controls Horizontal...

English
English-9
OSD LOCK OUT
This control completely locks out access to all OSD control functions without Volume, Brightness and Contrast.
When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are
locked out. To activate the OSD Lock Out function, press “12/ RESET”, then “+” key and hold down
simultaneously. To de-activate the OSD Lock Out, press “12/ RESET”, then “+” key and hold down
simultaneously.
RESOLUTION NOTIFIER
If ON is selected, a...