NEC Multisync Lcd1970vx Users Manual

User's Manual
MultiSync LCD1970V
MultiSync LCD1970VX
MultiSync LCD1970NX
 

Index
 Warning ....................................................................................................................1
  Contents ...................................................................................................................
2
  Display Setup ...........................................................................................................
3
  Mounting...

1
CAUTION:  TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM  
  WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER  
  CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS  
  INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
  This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause  
  electric shock. Therefore, it is dangerous to make any kind of contact with any...

2
Contents
*  Remember to save your original box and packing material to transport or ship the monitor.
User's Manual
MultiSync LCD1970V
MultiSync LCD1970VX
MultiSync LCD1970NX
Power CordMini D-SUB Cable
User ’s Manual
Your new NEC MultiSync® LCD monitor box* should contain the 
following:
•  MultiSync LCD1970V, LCD1970VX or LCD1970NX monitor with height 
    adjustable stand
•  Power Cord    • User’s Manual 
•  USB Cable (NX only)  • Cable Management Cover
•  Video Signal Cable (mini D-SUB 15 pin...

3
Display Setup
To attach the MultiSync® LCD monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output (NX and VX only): Connect the DVI signal 
cable to the connector of the display card in your system (Figure 1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure 2).  Tighten all screws. For MAC setup: Connect the Macintosh...

4
B TypeUSB Device
B Type
D
is pla y  Setup  -continued
Figure 4
30•  Tilt
Highest
Stand
Position DVI Cable
Input1(DVI)
DC-OUT
Input2(D-Sub )
(NX only)
( NX only) USB
Power cord
Figure 5
Figure 
1 Figure 2 Figure 3
DVI Signal Cable
Macintosh Cable Adapter (not included)
Note: Some Macintosh systems do not require a Macintosh 
Cable Adapter
Figure 6
(NX and VX only) 
DVI Cable
(Top)
Power Cable
(Bottom)
USB Cable
D-SUB Cable
NEC optional product atttachment. 
Do not use this connector unless specified....

5
Display Setup -continued
Figure 11
Power Button
VacationSwitch
Figure 9Figure 8
Figure 7
OFF PositionON Position
Figure 10
 

6
Display Setup -continued
Raise and Lower Monitor Screen
The monitor may be raised or lowered. To raise or lower screen, place hands on 
each side of the monitor and lift or lower to the desired height (Figure RL.1).
NOTE:  Handle with care when raising or lowering the monitor screen.
Tilt and Swivel
Grasp both sides of the monitor screen with your hands and adjust the tilt and 
swivel as desired (Figure TS.1).
NOTE:  Handle with care when tilting and swiveling the monitor screen.
Figure RL.1
Figure...

7
Mounting
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1.  Place hands on each side of the monitor and lift up to the highest position.  
Remove the cable cover (Figure M.1).
NOTE:  If you have difficulty removing the cable cover, please 
push the cover up (towards the top of the monitor) in order to unhook the cover from the stand, then remove, as shown in (Figure). Handle with care when 
removing cable cover.  
2.  Disconnect all cables.
3.  Place monitor...

8
Flexible Arm Installation
This LCD monitor is designed for use with a flexible arm. To mount the monitor to 
a flexible arm:
1.  Follow the instruction on how to Remove Monitor Stand for Mounting to 
remove the stand.
2.  Use the 4 screws from the stand removal to attach the arm to the monitor 
(Figure F.1).
NOTE:  The LCD monitor should only be used with an approved arm (e.g. GS mark).  To meet the safety requirements, the monitor must be mounted to an arm which 
guaranties the necessary stability...