NEC Multisync Ea222wme Users Manual

MultiSync EA222WMe
User’s Manual
 

Index
Warning, Caution ........................................................................\
....................................... .......... English-1
Registration Information ........................................................................\
............................... ........ English-1
Recommended use ........................................................................\
........................................ ...... English-3
Contents...

English
English-1
WARNING
CAUTION
CAUTION: TO  REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
W ALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have\
 sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind...

English-2
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian In\
terference-Causing Equipment Regulations.
C-UL:  Bears the C-UL Mark and is in compliance with Canadian Safety Regulation\
s according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync EA222WMe (L228NB)\
 color monitor so as not to interfere with radio
and television reception.
(1) The power supply cord you...

English
English-3
Recommended use
Safety Precautions and MaintenanceFOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR:
• DO NOT OPEN THE MONITOR.  There are no user serviceable parts inside and opening or removing cover\
s may expose
you to dangerous shock hazards or other risks. Refer all servicing to qu\
alified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water\
.
• Do not insert objects of any kind...

English-4
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CANREDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR:
• For optimum performance, allow 20 minutes for warm-up.
• Adjust the monitor height so that the top of the screen is at or slightl\
y below eye level.
Your eyes should look slightly downward when viewing the middle of the sc\
reen.
• Position your monitor no closer than 40 cm and no further away than 70 c\
m from your
eyes. The optimal distance is 50...

English
English-5
Contents
Your new NEC MultiSync LCD monitor box* should contain the following:
• MultiSync LCD monitor with tilt/swivel/pivot/height adjust stand
• Power Cord
• Cable cover
•V ideo Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)
•V ideo Signal Cable (DVI-D to DVI-D)
• USB Cable
• Audio Cable
• Setup Manual
Power Cord
(Type of power cord included will depend on the where the
LCD monitor is to be shipped)
Setup Manual 15-pin mini D-SUB male to
15-pin mini D-SUB male DVI-D...

English-6
Quick Start
To attach the MultiSync LCD monitor to your system, follow these instructio\
ns:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output:  Connect the DVI signal cable to the connector of the display card in you\
r
system ( Figure A.1 ). Tighten all screws.
For the PC with Analog output:  Connect the 15-pin mini D-SUB signal cable to the connector of the disp\
lay card in your
system ( Figure A.2 ). Tighten all screws.
For the MAC:  Connect the...

English
English-7
Figure C.2
5. To keep the cables neatly organized, place them into the cable management\
 system that is built into the stand.Place the Power cord and DVI cables into the specific hooks, as indicate\
d in  Figure C.2/Figure C.3.
Place the D-Sub and the USB cables into the specific hooks, as indicated\
 in  Figure C.2/Figure C.3.
6. Make sure all cables are resting flat against the stand ( Figure C.2/Figure C.3).
Please check Tilt, Rise and Lower monitor screen and screen rotation when...

English-8
8. Connect the power cord to the power outlet (Figure E.1).
NOTE: Please refer to  Caution section of this manual for proper selection of AC power cord.
9. The Vacation Switch on the back side of the monitor, near the AC inlet, must be turned on. Turn on the monitor with the front power button and then the computer ( Figure E.1).
NOTE: The Vacation Switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be t\
urned on
using the front button. DO NOT switch...