NEC Mt600 Lcd Projector Users Manual

to Òon.Ó) Either connector can be used for input or output, however they cannot both be
used for input simultaneously. It can damage your computer.
8.External Monitor Select SwitchThis switch should be Òof fÓ for normal use without
external termination or when your RGB signal should be terminated with 75W. Switch to
the ÒOnÓ position when you have a monitor attached to your RGB through-put connec-
tor.
9.RGB Audio Input Mini JackThis is where you connect RGB audio output from a
computer or another RGB...

42MAINTENANCE
3. Remove the two screws securing the lamp case. (There is an interlock on
this case to prevent the risk of electrical shock. Do not attempt to
circumvent this interlock.)
4. Use the lamp case handle to remove the assembly.
5. Install a new lamp case assembly and secure it in place with the two
screws.
CAUTION: Do not use lamps other than the NEC optional lamp.
Order by your projections model number.
6. Reattach the lamp cover and reinstall the single screw.
7. After you install a new lamp,...

POSITION RGB
ZOOMS-VIDEO
FOCUS VIDEO
MENU
SELECT
PICTURE
ON+
–
DISPLAY
OFF MUTE
POWER
2X/4X FREEZE
12.(+) (-) ButtonsAfter you make your on-screen menu selection use this button to
adjust the level up or down. (See page 35.)
13.Picture Mute ButtonThis button turns off the image for a short period of time.
14.Display Mute ButtonThis button will turn off the on-screen icon menu bar.
15.Power On And Off If your main power switch is turned on, you can use this button
to turn your MultiSync MT600 LCD...

Lamp Usage This tells you how long the lamp has been in operation. It is
recommended that you replace a lamp after 2000 hours of service. To see
the time used, select this icon and press the (+) button. After you install a
new lamp, select this icon and press and hold the ÒPower OnÓ button for ten
seconds to reset the lamp clock back to zero.
Reset Changes all adjustments to the factory preset levels for each source
individually. To activate, you must press the (+) button on the cabinet or
remote for at...

Using A Tabletop Or Cart
1. Place your LCD projector on a flat level surface at the optimal distance from
the screen or wall so you realize the size image you want. (Avoid having
bright room lighting or sun light directly on the screen or wall where youÕll
be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the projector on. (If
no input signal is available, the projector will display a black screen.)
3. Ensure that the projector is square to the screen.
4. Move the...

38 Projector Control Icons
Auto Start  Turns the LCD projector on automatically when the
main power switch is turned on. This eliminates the need to always
use the ÒPowerÓ button on the remote control or projector cabinet.
Auto Picture When on, the ÒPictureÓ and ÒFine PictureÓ adjust-
ments are made automatically.**
High-Contrast Increases contrast so the image from a document
camera is easier to see.
Speakers  Turns the projector Õs speakers on and off.
Power Management When ÒPower ManagementÓ is on...

26 If your projector is mounted on the ceiling and your image is upside down, use the
ÒMenuÓ and ÒSelectÓ buttons on your remote control or projector cabinet to access the
icons that will correct the orientation. (See page 39.)
Reflecting The Image
Using a mirror to reflect your LCD projectorÕs image enables you to enjoy a much
larger image. Contact your NEC dealer if you need a mirror.
If youÕre using a mirror and your image is inverted, use the ÒMenuÓ and ÒSelectÓ
buttons on your remote control or...

36OPERATION
Icon Descriptions & Functions
Source Icons
Selects a video source (NTSC, PAL, SECAM, orM-NTSC) such as a  VCR
or laser disc player.
Selects an S-video source.
Selects an RGB source such as a computer or document camera.
Sound And Picture Control Icons
Volume
Brightness
VCR or Laser Disc Player
To mini D-Sub 15-pin or
D-Sub 15-pin connector
on the LCD Projector.
IR Receiver Document Camera
IBM VGA or Compatibles
Wiring Diagram
NOTE: The two D-Sub 15-pin connectors here can be used to either...

PC
CONTROLS-VIDEO
INPUTL / MONO R
AUDIO INPUTVIDEO
INPUTDC12V/400mA
OUTPUT
RGBREMOTE
CONTROLAUDIO
INPUTAUDIO
OUTPUT
28INSTALLATION
Remote control in
wired operation.
Macintosh or Compatibles
IR Receiver
MAC mouse adapter (supplied)
IBM/MAC MultiCable
35
CAUTIONDo not unplug the projector while the cooling fan is on. The fan will remain on
as long as there is heat inside the LCD projector and the main power switch is
on.
Using The Icons
1. Press the ÒMenuÓ button on the remote control or projector...

29
Connecting Your PC Or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync MT600 LCD Projector
will enable you to project your computerÕs screen image for an impressive presenta-
tion. All of these following display standards are supported:
VGA 640 x 480 for graphics,VGA 640 x 400 for graphics,VGA 640 x 350 for
graphics,VGA 720 x 400 for text,VGA 720 x 350 for text,Macintosh at 640 x 480
To connect to a PC, Macintosh or computer equipped with a VGA adapter or compat-
ible...