NEC Mt600 Lcd Projector Users Manual

10
2. Costs of initial technical adjustments (set-up), including adjustment of
user controls. These costs are the responsibility of the NECTECH dealer
from whom the product was purchased.
3. Payment of shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you
purchased the product.
2. Whenever warranty service is required, the original dated invoice (or a
copy) must be presented as proof of warranty coverage. Please be
prepared to describe...

Problem Check These Items
Image is scrolling Use icons to select the source you
vertically, want to input.
horizontally or both
Remote control Install new batteries. (See page 44.)
does not work
Make sure there are no obstacles between
you and the projector.
Make sure you are within 23 feet (7m)
of the projector.
Status indicator is lit See the Status Light message charton page 49.
or blinking
Cross color in If ÒAuto PictureÓ is off, turn it on. If ÒAuto
RGB mode PictureÓ is on, turn it off and balance...

12
3. Operation
General Controls ................................................................................................................. 33
Using The Icons .................................................................................................................. 35
Icon Descriptions And Functions ........................................................................................ 36
Source Icons...

Condition Status
Blinking Rapidly The projector is overheated. The lamp turns
(4 times a second) off automatically. Allow the fan to run at least
two minutes before unplugging the projector.
Then check the filter and clean it if necessary.
If there is insufficient ventilation around the
projector or if the room where youÕre presenting
 is particularly warm, move the projector to
a cooler location. In either case, allow at least
five minutes before turning the projector back
on. If the problem persists,...

¥ Supports most IBM VGA, S-VGA (pseudo), Macintosh or any
other RGB signals within a horizontal frequency range or 15 to
40 kHz and a vertical frequency range of 50 to 75 Hz. This
includes NTSC, PAL, SECAM, and M-NTSC standard video
signals.
Note:  Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S.
and Canada.
PAL: TV standard used in western Europe
SECAM: TV standard used in France and
Eastern Europe
M-NTSC: (modified-NTSC)-result of converting
a video in the SECAM...

48
AVERTISSEMENT
¥ Nettoyer seulement lÕextŽrieur du filtre avec un aspirateur.
¥ 
Žtiquette dÕavertissement.
¥ Ne pas essayer de faire fonctionner le projecteur sans un filtre.
¥ Votre projecteur ˆ Žcran ˆ cristaux liquides (LCD) ne  fonctionnera pas si le
filtre est installŽ incorrectement.
¥ 
remplacer lÕampoule et/ou le filtre ˆ air.
A
How Do You Get Started?
The fastest way to get started is to take your time and do every-
thing right the first time. Taking a few minutes now to watch the...

16
Carrying handle
Feet
One Touch
Tilt buttons
Remote sensor
Lens with Lens cover
Built-in speakers (1W22)
Getting To Know Your MultiSync MT600 LCD
Projector
Front Features Rear Features
Lamp cover
Lamp cover set screw
Main POWER switch
AC INPUT
Connect the supplied power
cableÕ s three-pin plug here.
INTRODUCTION
Ventilation holes(inlet)
Remote SensorRemote sensor
Nettoyer et remplacer le filtre
Le filtre ˆ air Žponge emp ö intŽrieur du
projecteur ˆ Žcran ˆ cristaux liquides (LCD) et devrait ö
dÕusage...

5. Installer une nouvelle ampoule et fixer le coffret de lÕampoule avec les deux vis.
PRECAUTION: Ne pas utiliser dÕautres ampoules que lÕampoule NEC en option.

6. Replacer le couvercle de lÕampoule et fixer avec la vis.
7. one de lÕusage de
lÕampoule, presser sans relacher le bouton ÒPower OnÓ sur l appareil ˆ
tŽlŽcommande pendant 10 seconds afin de remettre lÕhorloge de lÕampoule a zero.
NOTE: Quand vous remplacez lÕampoule, il est recommande de changer aussi le filtre.
46
POWER
PUSH ON/OFF
MENU...

If this light blinks red rapidly, it indicates that either the lamp cover or filter cover
is not attached properly. It may also indicate that the projectorÕs internal tempera-
ture is too high to operate safely. In either case, the projector will not work until
the situation is corrected.
Terminal Panel Features
This panel is located below the projectorÕs handle and is where you connect your
cables. To gain access, push on the upper right hand corner of the panel door.
1.Remote Control Jack  Connect your...

44
CAUTION
¥ Only clean the outside of the filter with a vacuum cleaner.
¥ Do not clean inside the projector where the filter is positioned and the caution
label is placed.
¥ Do not attempt to operate the projector without a filter.
¥ Your LCD projector will not operate unless the filter is installed correctly.
¥ Do not put the LCD projector on end except for lamp and/or air filter
replacemant.
MAINTENANCE
A
–
+
REMOTE
CONTROLPC
CONTROLS-VIDEO
INPUT
VIDEO

 L/MONO      R

AUDIO INPUTVIDEO
INPUT...