NEC Mt1056 Lcd Projector Users Manual
Have a look at the manual NEC Mt1056 Lcd Projector Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
E – 11 PJ FOCUS ZOOM VOLUME SHIFT HELP POINTER KEYSTONEMAGNIFY FREEZE PIC-MUTEPC CARDSLIDE FOLDER SLIDE LIST 17 19 20 28 29 30 31 22 18 21 23 24 25 26 27 17. PJ Button Press this button to switch the Select, Cancel, and Enter buttons be- tween the Projector mode (lit red) and the Computer mode. Press this button or any one of the Power ON/OFF, Menu, Help, Pointer, Magnify, PC Card, Folder List or Slide List buttons to switch to the Projector mode and the PJ button lights red. To switch back to the Computer mode, press the PJ button again. 18. FOCUS Button Not available on this model. 19. ZOOM Button Not available on this model. 20. SHIFT Button Not available on this model. 21. HELP Button Provides information about operation and adjustment procedures or the set information for the current menu or adjustment during menu operation. 22. POINTER Button Press this button to display one of the eight pointers; press again to hide the pointer. You can move your pointer icon to the area you want on the screen using the Select button. 23. KEYSTONE (+) (–) Button Press the (+) or (–) button to correct the keystone (trapezoidal) distor- tion, and make the image square.24. MAGNIFY (+) (–) Button Use this button to adjust the image size up to 400%. When the pointer is displayed, the image is magnified about the center of the pointer. When the pointer is not displayed, the image is magni- fied about the center of the screen. When the image is magnified, the pointer is changed to the magnifying icon. 25. FREEZE Button This button will freeze a picture. Press again to resume motion. 26. PICTURE MUTE Button This button turns off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: When the menu is displayed, a press of this button mutes an image and sound without turning off the menu. 27. VOLUME (+) (–) Button Press (+) to increase the volume and (–) to decrease it. 28. PC CARD Button Press this button to select the PC Card Viewer source. 29. SLIDE (+) (–) Button Press (+) to select the next folder or slide and (–) to select the previous folder or slide. 30. FOLDER LIST Button Press this button to select PC Card Viewer source to display a list of folders included in a CompactFlash card. 31. SLIDE LIST Button Press this button to select PC Card Viewer source to display a list of slides included in a CompactFlash card. *NOTE: The default is the Computer mode, which allows you to use the Select, Cancel, and Enter buttons as your computer mouse. When the POWER ON/ OFF, MENU, HELP, POINTER, MAGNIFY, PC CARD, FOLDER LIST, or SLIDE LIST button is pressed, the PJ button lights red to indicate that you are in the Projector mode. If no buttons are pressed within 10 seconds, the light goes out and the Projector mode is canceled.
E – 12 Operating Range 7m Remote Control Precautions•Handle the remote control carefully. •If the remote control gets wet, wipe it dry immediately. •Avoid excessive heat and humidity. •If you will not be using the remote control for a long time, remove the batteries. •Do not place the batteries upside down. •Do not look into the laser pointer while it is on. •Do not point the laser beam at a person. Remote Control Battery Installation 1. Press firmly and slide the battery cover off. 2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries’ polarity (+/–) aligned correctly. 3. Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries. Note on Remote Control Operation: Pressing and holding the Select (, , , )/ Mouse button while installing new batteries may cause malfunction or no operation. Should this happen, remove the batteries and then install them again without touching the Select/Mouse button. Setting the function switch ON OFF There are two switches on the bottom of the battery case: an appli- cable projector selector switch (1) and laser enable/disable switch (2). Check the projector being used and decide whether to enable or dis- able laser, then set these switches as necessary using the tip of a thin ball-point pen. On this model, an applicable projector selector switch (1) is not used. Switch (2) On: Enabled (the laser lights when the LASER button is pressed) [Fac- tory default] Off: Disabled (the laser does not light even when the LASER button is pressed) Disable the laser when using in an environment in which the unit is accessible to children.
E – 13 Switching operation mode between computer and projectorThe three shaded buttons shown on the drawing work as a computer mouse in the Computer mode. In the Computer mode the PJ button is not lit. •When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu operation using the three buttons. •When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT , , , button works as a moving button for the POINTER or magnified image. •If no buttons are pressed within 10 seconds, the PJ button’s light goes out to indicate that you are in the Computer mode. To enable the projector menu operation again, press the PJ button to light red. To move the pointer or a magnified image again, turn off the pointer and then turn on the pointer (press the POINTER button two times). •When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the Computer mode (not lit). Works as the Select button on the projector. MENU ENTERCANCEL PJ FOCUS ZOOM OFF VIDEO AUTO ADJ. S-VIDEO RGB1 RGB2 LASERON VOLUME SHIFT HELP POINTER KEYSTONEMAGNIFY FREEZE PIC-MUTEPC CARDSLIDE FOLDER SLIDE LIST SELECT POWER MENU ENTERCANCEL FOCUS ZOOM OFF VIDEO AUTO ADJ. S-VIDEO RGB1 RGB2 LASERON VOLUME SHIFT HELP POINTER KEYSTONEMAGNIFY FREEZE PIC-MUTEPC CARDSLIDE FOLDER SLIDE LIST SELECT POWER PJ Not lit Works as a mouse for your computer. Works as a right-click button for your computer. Works as a left-click button for your computer. Lit red Works as the Enter button on the projector. Works as the Cancel button on the projector. During Computer mode: During Computer mode by pressing the ENTER button for 1.5 sec- onds or more then releasing, the drag mode is set and the drag opera- tion can be performed simply by pressing the SELECT (, , , ) (mouse) button. To cancel the drag mode, press the ENTER (left click) button again or press the CANCEL (right click) button.
E – 14 2. INSTALLATION This section describes how to set up your MT1056 projector and how to connect video and audio sources. Setting up Your ProjectorYour MT1056 Projector is simple to set up and use. But before you get started, you must first: 1. Determine the image size. 2. Set up a screen or select a non-glossy white wall onto which you can project your image. Carrying the Projector: Always carry your projector by the handle. Ensure that the power cable and any other cables connecting to video sources are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap. Carrying handle MENUENTERCANCEL SELECT POWER STATUS ON /OFF SOURCEAUTO ADJUST USB AC IN Attaching the lens cap to the lens hood with the supplied string and rivet. Selecting a LocationThe further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 30" (0.76 m) measured diagonally when the projector is roughly 4 feet (1.3 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 36.8 feet (11.2 m) from the wall or screen. Using a Tabletop or Cart1. Place your projector on a flat level surface at the optimal dis- tance from the screen or wall so you realize the size image you want. (Avoid having bright room lighting or sun light directly on the screen or wall where you’ll be projecting the image.) 2. Connect the power cable, remove the lens cap and turn the pro- jector on. (If no input signal is available, the projector will display a background image.) 3. Ensure that the projector is square to the screen. Lens cap String 4. Move the projector left or right to center the image horizontally on the screen. 5. To center the image vertically, lift the front edge of the projector and press the One-Touch Tilt button on the front-left side of the projector to release the Front Adjustable foot. Top view Screen (There is approximately 5 degrees of up and down adjustment for the front of the projector.) 6. If the projected image does not appear square to the screen then use keystone correction for proper adjustment. 7. Adjust the size of the image using the Zoom ring on the lens. Side view Screen AC IN Rivet
E – 15 MENUENTERCANCELSELECT POWER STATUS ON/OFF SOURCEAUTO ADJUST AC IN MENUENTERCANCELSELECT POWER STATUS ON/OFF SOURCEAUTO ADJUST AC IN Adjusting the Tilt FootPress and hold the Tilt button on the left side of the projector. Lift the front edge of the projector to the height you want, and release the button to lock the Adjustable Tilt Foot. To fine-tune the image’s position vertically on the screen, rotate the foot. Each of the rear feet height can be changed up to 0.6" (4mm).
E – 16 Screen and Projection DistanceThe following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation. 558.8 (W ) 419.1 (H) / 220 (W ) 165 (H) W IDE : 300" 609.6 (W ) 457.2 (H) / 240 (W ) 180 (H) 406.4 (W ) 304.8 (H) / 160 (W ) 120 (H) 487.7 (W ) 365.8 (H) / 192 (W ) 144 (H) 304.8 (W ) 228.6 (H) / 120 (W ) 90 (H) 243.8 (W ) 182.9 (H) / 96 (W ) 72 (H) 203.2 (W ) 152.4 (H) / 80 (W ) 60 (H) 162.6 (W ) 121.9 (H) / 64 (W ) 48 (H) 121.9 (W ) 91.4 (H) / 48 (W ) 36 (H) 81.3 (W ) 61.0 (H) / 32 (W ) 24 (H) 67.1 (W ) 50.3 (H) / 26 (W ) 20 (H) TELE: 30" 61.0 (W ) 45.7 (H) / 24 (W ) 18 (H) Screen size (Unit: cm/inch) Lens center Screen Distance (Unit: m/feet) 60" 80" 100" 120" 150" 200" 240" 275" 40"33" 1.3/4.3 1.6/5.22.4/7.9 3.2/10.5 4.0/13.1 4.9/16.1 6.1/20.0 8.2/26.9 9.8/32,211.2/36.7 Throw distance
E – 17 Ceiling Installation Distance Chart B = Vertical distance between lens center and screen center C = Throw distance D = Vertical distance between lens center and screen bottom (screen top for ceiling installation) NOTE: Distances may vary +/–5%. 10.3 10.1 10.1 10.0 10.0 10.0 10.0 9.9 9.9 9.9 9.8 9.8 9.8 9.8 Diagonal Width Height wide telephoto wide telephotoB C Screen Size Dα40 1016 60 1524 67 1701.8 72 1828.8 84 2133.6 90 2286 100 2540 120 3048 150 3810 180 4572 210 5334 240 6096 270 6858 300 7620inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm32 812.8 48 1219.2 53.6 1361.44 57.6 1463.04 67.2 1706.88 72 1828.8 80 2032 96 2438.4 120 3048 144 3657.6 168 4267.2 192 4876.8 216 5486.4 240 609624 609.6 36 914.4 40.2 1021.08 43.2 1097.28 50.4 1280.16 54 1371.6 60 1524 72 1828.8 90 2286 108 2743.2 126 3200.4 144 3657.6 162 4114.8 180 4572 inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mminch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm10.2 259.5 15.3 389.2 17.1 434.7 18.4 467.1 21.5 544.9 23.0 583.9 25.5 648.7 30.6 778.5 38.3 973.1 46.0 1167.7 53.6 1362.3 61.3 1557.0 69.0 1751.6 76.6 1946.2inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm56.3 1430.3 86.1 2185.8 96.5 2450.2 103.9 2639.0 121.7 3092.3 130.7 3318.9 145.5 3696.6 175.3 4452.1 219.9 5585.2 264.5 6718.4 309.1 7851.5 353.7 8984.7 398.3 10117.8 443.0 11251.0inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm68.6 1743.7 104.3 2649.9 116.8 2967.1 125.7 3193.7 147.1 3737.4 157.8 4009.3 175.7 4462.4 211.4 5368.7 264.9 6728.0 318.4 8087.4 371.9 9446.8 425.4 10806.2 479.0 12165.5 532.5 13524.9inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm1.8 45.3 2.7 68.0 3.0 75.9 3.2 81.5 3.7 95.1 4.0 101.9 4.5 113.3 5.4 135.9 6.7 169.9 8.0 203.9 9.4 237.9 10.7 271.8 12.0 305.8 13.4 339.8inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mmdegree degree degree degree degree degree degree degree degree degree degree degree degree degree– – – – – – – – – – – – – –8.5 8.4 8.3 8.3 8.3 8.3 8.3 8.3 8.2 8.2 8.2 8.2 8.2 8.2degree degree degree degree degree degree degree degree degree degree degree degree degree degree – – – – – – – – – – – – – – If your projector is mounted on the ceiling and your image is upside down, use the “Menu” and “Select” buttons on your projector cabinet or button on your remote control to correct the orientation. (See page E-36.) Reflecting the ImageUsing a mirror to reflect your projector’s image enables you to enjoy a much larger image. Contact your NEC dealer if you need a mirror. If you’re using a mirror and your image is inverted, use the “Menu” and “Select” buttons on your projector cabinet or buttons on your remote control to correct the orientation. (See page E-36.) WARNING•Installing your projector on the ceiling must be done by a qualified technician. Contact your NEC dealer for more information. * Do not attempt to install the projector yourself. •Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged. •Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 32°F (0°C) and 104°F (40°C). •Do not expose the projector to moisture, dust, or smoke. This will harm the screen image. •Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the side or the front of the projector. Throw Angle (α) Throw Distance (C) 2.9 (79.5mm) Lens CenterScreen top Screen center Screen BottomD B Projector Foot Projector Foot Screen top 2.9 (79.5mm) Lens Center Screen center Screen Bottom Throw Distance (C)Throw Angle (α) B D
E – 18 PC CONTROLREMOTE CONTROL INPUT MOUSE OUTPUT S-VIDEO VIDEO AUDIO RGB INPUT 2 AUDIO RGB INPUT 1 L/MONO R AUDIORGB MONITOR OUTPUT Wiring Diagram NOTE: When using with a notebook PC, be sure to connect between the projec- tor and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector. NOTE: If using video, S-video, or audio cables, the cables should be 3 m (9.8feet) or shorter. Supplied serial cableSupplied mouse adapter (For USB) Supplied mouse adapter (For IBM PS/2 or USB)Macintosh or Compatibles (Desktop type or notebook type) IBM VGA or Compatibles(Desktop type or notebook type) DVD Player (with component output) Document Camera To video, S-video, and audio inputs on the projector. VCR, DVD Player or LaserDisc PlayerMonitor Remote Control Guideline1. Plug the supplied serial cable with the mouse output port of the pro- jector into your computer’s mouse port and restart your computer to gain remote mouse control. 2. When using the remote control’s built-in infrared mouse on a laptop computer, the laptop’s mouse, trackball or trackpad will be disabled. Disconnect the serial cable from the mouse output port and restart your computer to regain trackball or trackpad mouse control. 3. If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software. 4. If you accidentally hit the OFF button on the remote control, wait one full minute and then press the ON button to resume.Signal cable (supplied) To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a sig- nal cable longer than the one supplied. Component video cable RCA3 (not supplied) Optional 15-pin-to-RCA (female)3 cable (ADP-CV1)
E – 19 MENUENTERCANCELSELECT POWER STATUS O N/S T A N D B YSOURCE AUTO ADJUST A C I NS - V I D E O V I D E O A U D I OR G B I N P U T 2A U D I OR G B I N P U T 1 L/M O N O R A U D I OR G B M O N I T O R O U T P U T U S B P C -C A R DC C O N T R O LM O U S E O U TR E M O C O N T R I N P U S-VIDEO VIDEO AUDIO RGB INPUT 2 A U D IOR G B IN P U T 1 L/MONO R A U D IOR G B M O N IT O R O U TP U T RGB INPUT AUDIO RGB signal cable (supplied)To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribu- tion amplifier if connecting a signal cable longer than the one supplied. IBM VGA or Compatibles (Desktop type)Audio cable (not supplied) Connecting Your PC or Macintosh Computer IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type) 1O ND I P 23456 Pin adapter for Macintosh (not supplied) For older Macintosh, use a commercially available pin adapter to connect to your Mac’s video port.The new Macintosh computer such as G3 will have the 15 pin HD connec- tor. The MT1056’s “Plug and Play” data will be downloaded to the Macintosh. Therefore, a Mac adapter will not be necessary. Macintosh (Desktop type) Connecting your PC or Macintosh computer to your MT1056 (XGA) projector will enable you to project your computer’s screen image for an impressive presentation. To connect to a PC or Macintosh, simply: 1. Turn off the power to your projector and computer. 2. Use the signal cable that’s supplied to connect your PC or Macintosh computer to the projector. 3. Turn on the projector and the computer. 4. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you’ve connected to the projector.
E – 20 MENUENTERCANCELS E L E C T P O W E R S T A T U S O N/S T A N D B YS O U R C EA U T O A D J U S T A C I NS - V I D E O V I D E O A U D I OR G B I N P U T 2A U D I OR G B I N P U T 1 L/M O N O R A U D I OR G B M O N I T O R O U T P U T U S B P C - C A R DC C O N T R O LM O U S E O U TR E M O C O N T R I N P U NTROLMOUSE OUTPUTREMO CONTR INPUMOUSE OUTPUT Serial cable (supplied) Macintosh with USB Port IBM PS/2 The built-in remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations. To connect the mouse output port: 1. Turn off your computer. 2. For PCs: Remove your current mouse and connect the supplied serial cable from the mouse output to your PC’s mouse port. (Use the 6-pin adapter for connecting to a PS/2 computer or the supplied USB adapter.) For Macintosh: Attach the supplied mouse adapter for USB to the mouse output port’s serial cable and connect the projector to your USB port of a Macintosh computer. 3. When the built-in remote mouse receiver is available, it will disable your regular mouse, disconnect the serial cable and restart your computer. NOTE: The mouse adapter for USB is not compatible with the USB terminal on the projector. Connecting Your Computer to the Mouse Output Port Mouse adapter (For IBM PS/2) (supplied) Mouse adapter (USB) (supplied)