NEC Mt1030+ Projector Users Manual

							11
Top Features
1 Power Button
Use this button to turn the power on and off when the Main Power Switch is on and
the LCD projector is in standby.
2 Menu Button
Displays the on- screen menu.
3 Select (st
§ ©) / (+)(Ð) Buttons
Select: After you press the ÒMenuÓ button, use the s or t button to select the
menu icon of the item you wish to adjust.
(+)(Ð): Use these buttons while you re in the Image Adjust mode to change the
level of a selected menu item. These buttons are also used to set an item
in the Power or Settings menus.
4 Enter Button
Executes your menu selection.
5 (+) (Ð)  Zoom Buttons
Press the (+) button to make the image larger; press (Ð) to make the image smaller.
6 (+) (Ð)  Focus Buttons
Press the (+) or (Ð) buttons to focus an image.
7 Power Indicator
When this indicator is green, the LCD projector is on; when the indicator is amber, it
is standing by.
8 Status Indicator
When this is lit red continually, its warning you that the projection lamp has exceed
2000 hours of service. After this light appears, it is advisable to replace the projection
lamp as soon as possible.(See pages 83 and 84)
In addition the message LAMP USAGE XX HOURS appears continually when
the on-screen menu is not displayed.
If this light blinks red rapidly, it indicates that either the lamp cover or filter cover is
not attached properly. See the Status Light Messages on page 91 for more details.
INTRODUCTION19
20
MENU
SELECT
ENTER
ON/OFF
ZOOM FOCUS
STATUS
POWER
–
+
–+
–+
2
3
4
6
51
8
7
(st§ ©) 
						

							12
Terminal Panel Features
This panel is located on the left side and is where you connect your cables.
INTRODUCTION21
22
PC CONTROL MOUSE OUTPUTREMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
13
24 1 S-Video Input
Here is where you connect the S-Video input from an external
source like a VCR.
Left Channel/Mono Audio Input Jack
This is your left channel audio input for stereo sound coming from
S-Video equipment or audio system.  This also serves as your
monaural audio input.
Right Channel Audio Input Jack
This is your right channel audio input for stereo sound.
NOTE:  S-Video provides more vivid color and higher resolution
than the traditional composite video format.
2 Video Input
Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
Left Channel/Mono Audio Input Jack
This is your left channel audio input for stereo sound coming from
video equipment or audio system. This also serves as your monaural
audio input.
Right Channel Audio Input Jack
This is your right channel audio input for stereo sound.
3 RGB Monitor Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an
external monitor from either the RGB 1 or RGB 2 input source.
Audio Output Mini Jack
Connect additional external speakers here to listen to audio coming
from your computer, Video or S-Video input.
4 RGB Input 1 Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment such as IBM or compat-
ible computers. Use the signal cable thats supplied to connect to a
PC. Or connect a Macintosh or compatible computer here using the
signal cable and the pin adapter that is supplied.
RGB 1 Audio Input Mini Jack
This is where you connect RGB audio output from a computer or
another RGB source. 
						

							13INTRODUCTION23
24 5 RGB Input 2 Connector (Mini D-Sub 15 pin)
Connect a Macintosh or compatible computer here using the signal
cable and the monitor adapter that is supplied. Or connect your PC
or other RGB equipment such as IBM or compatible computers.
Use the signal cable that is supplied to connect to a PC.
RGB 2 Audio Input Mini Jack
This is where you connect a second RGB audio output from a
computer or another RGB source.
6 PC Control Port
Use this port to connect your PC to control the MultiSync MT830+/
MT1030+/MT1035+ Projector. This enables you to use your PC
and serial communication protocol to control the projector. If you
are writing your own program,  command references are on pages
103 to 106.
A cap is put on the port at the factory. Remove the cap when using
the port.
7 Mouse Output Port
Use this port to operate your computerÕs mouse functions from the
NEC MultiSync MT830+/MT1030+/MT1035+ remote control.
When your computer is connected here, the remote sensors on the
LCD projector cabinet will receive your mouse commands.
8 Remote Control Jack
Connect your remote control cable here for wired operation.
9 Built-in Security Slot ( 
 )
This security slot supports the MicroSaver
¨ Security System.
MicroSaver
¨  is a registered trademark of Kensington Microware
Inc.  The logo 
 is trademarked and owned by Kensington
Microware Inc.
PC CONTROL MOUSE OUTPUTREMOTE
CONTROL
INPUT
AUDIO RGB   INPUT   2
AUDIO RGB   INPUT   1
AUDIO RGB MONITOR OUTPUTR L/MONO INPUT    AUDIO S–VIDEO
R L/MONO
INPUT    AUDIO VIDEO
678
5
AC IN
9 
						

							14
Remote Control Features
You can use your remote control with the cable or wireless to operate your
MultiSync MT830+/MT1030+/MT1035+ LCD Projector. With the mouse
output port connected to your computer, you can also use the projectors
remote control to operate your computers mouse wireless. (See pages 59
and 60 to connect your computer to the mouse output port.)
If you want to use your remote control with the cable, connect one end
of the cable to the jack on the remote control and the other end to the
Terminal Panel.
NOTE: If you are using a Macintosh computer, you can click either the
right or left button to activate the mouse.
1 Left Click Button
Use this button to enter your menu selection. It works the same as
the Enter button on the cabinet.
2 Laser Pointer
Beams a laser light when Laser button is pressed.
3 Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
INTRODUCTION25
26
OFF ON
PC CARD VIDEO
RGB 1
MENU
R-CLICK/CANCELLASER
SLIDE
VOLUME
S-VIDEO
POINTER
MAGNIFYPIC-MUTE FREEZE
RGB 2
+
–
+ –
+
–+
–
FOCUSKEYSTONEZOOM
+
–+
–+
–
POWER
4 LED
Flashes when any button is pressed.
5 Power On And Off
If your main power switch is turned on, you can use this button to turn your
MultiSync MT830+/MT1030+/MT1035+ LCD Projector on and off.
6 Video Button
Press to select an NTSC, PAL, SECAM or NTSC4.43 compatible
video source from a VCR, DVD player, laser disc player or docu-
ment camera.
7 S-Video Button
Press to select an S-Video source from a VCR.
8 RGB 1 Button
Press to select a video source from a computer connected to your
RGB 1 port.
9 RGB 2 Button
Press to select a video source from a computer connected to your
RGB 2 port.
10 PC Card Button
Press to display a slide from the flash memory card inserted in the
PC card slot of your LCD projector. (You must first install the
optional MT Viewer board into your LCD projector.)1
3 2
4
5
10 6
7
8
9 
						

							15INTRODUCTION27
28
OFF ON
PC CARD VIDEO
RGB 1
MENU
R-CLICK/CANCELLASER
SLIDE
VOLUME
S-VIDEO
POINTER
MAGNIFYPIC-MUTE FREEZE
RGB 2
+
–
+ –
+
–+
–
FOCUSKEYSTONEZOOM
+
–+
–+
–
POWER
15 Freeze Button
This button will freeze a picture. Press again to resume motion.
16 Picture Mute Button
This button turns off the image for a short period of time. Press
again to restore the image.
17 Pointer Button
Use this button to move your Pointer icon to the area you want on
the screen, then press the Magnify button on the remote control to
enlarge the selected area on the screen.
When youre finished, the Pointer button will remain lit for 10
seconds.
NOTE:
* Eight kinds of Pointers (icons) are available. You can select one
from the Settings Menu. The magnifying glass icon is selected at
the factory. See page 74 for more details.
* With the Pointer button pressed, the Mouse Pad is used to move
the picture.
18 Volume Button
Press (+) to increase the volume and (-) to decrease it.14
15
16 17
18 11 Laser Button
Press and hold this button to activate the laser pointer. When lit, you
can use the laser to draw your audiences attention to a red dot that
you can place on any object within 30 feet (10 m).
12 Menu Button
Use this button to call up the On-Screen Menu so you can adjust and
set the image. After you press this button, it will light up. During
this time you can use the mouse pad and right/left click buttons to
make menu selections.
If no buttons are pressed within 10 seconds while it illuminates, the
light goes out. To return to the main menu from a submenu, press
this button again.
13 Mouse Pad(st
§ © /+ -)
Works as a mouse for your projected computer image. This pad is
also used to adjust position.
This pad selects the submenu you want to adjust. (See page 63.)
After you make your on-screen menu selection, use this pad to
adjust the level up or down. (See page 63.)
14 Right Click/Cancel Button
Press this button to exit Menus or Pointer.
1112
13 
						

							16INTRODUCTION30 29
Remote Control Precautions
¥ Do not look into the laser pointer while it is on.
¥ Do not point the laser beam at a person.
¥ When the cable is connected to the remote control, it will not work
in the wireless mode.
¥ Handle the remote control carefully.
¥ If the remote control gets wet, wipe it dry immediately.
¥ Avoid excessive heat and humidity.
¥
If you will not be using the remote control for a long time, remove the
batteries.
¥ Do not mix new and old or different types of batteries. 19 Slide Button
Press (+) to advance the next file or slide and (-) to return to the
previous file or slide. (the optional MT Viewer board required)
20 Magnify Button
Use the (+) or (-) button to adjust the image size up to 400%.
When the Pointer is displayed, the magnified image is displayed at
the center of the Pointer.
When the Pointer is not displayed, the magnified image is displayed
at the center of the screen.
21 Keystone Button
Press the (+) or (-) button to correct the keystone (trapezoidal)
distortion, and make the image square.
22 Focus Button
Press the (+) or (-) button to adjust the focus.
23 Zoom Button
Press the (+) button to zoom in and the (-) button to zoom out.
24 Remote Jack
Connect your remote control cable here for wired operation.
NOTE: You cannot use Menu and Pointer at the same time.
OFF ON
PC CARD VIDEO
RGB 1
MENU
R-CLICK/CANCELLASER
SLIDE
VOLUME
S-VIDEO
POINTER
MAGNIFYPIC-MUTE FREEZE
RGB 2
+
–
+ –
+
–+
–
FOCUSKEYSTONEZOOM
+
–+
–+
–
POWER
19
20
21
22 23
24 
						

							17
This section describes how to set up your MultiSync MT830+/MT1030+/
MT1035+ LCD projector and how to connect video and audio sources.
Setting Up Your MultiSync MT830+/MT1030+/
MT1035+ LCD Projector
Your MultiSync MT830+/MT1030+/MT1035+ LCD Projector is simple to set
up and use. But before you get started, you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can project
your image.
Carrying The LCD Projector Always carry your LCD projector by the
handle. Ensure that the power cord and any other cables connecting to video
sources are disconnected before moving the projector. When moving the
projector or when it is not in use, cover the lens with the lens cap.
INSTALLATION 2
Selecting A Location The further your LCD projector is from the screen or
wall, the larger the image. The minimum size the image can be is approxi-
mately 20 (0.5 m: MT830+/MT1030+) / 25 (0.64 m: MT1035+) measured
diagonally when the projector is roughly 3 feet (1.0 m) from the wall or
screen. The largest the image can be is 300 (7.6 m: MT830+/MT1030+) /
320(8.1 m: MT1035+) when the projector is about 40.03 feet (12.2 m:
MT830+/MT1030+)/39.37 feet (12.0 m: MT1035+) from the wall or screen.
Throw Distance
Diagonal Screen Size (inch)
Projection Distance and Image Size
INSTALLATION31
32
Width
HeightScreen size
(diagonal)
Projection distance
RivetString
Lens capAttaching the lens cap to the lens hood
with the supplied string and rivet.
350
300
250
200
150
100
50
0
0.0 6.56 13.12 19.69 26.25 32.81 39.37 40.03 ft.
(2.0) (4.0) (6.0) (8.0) (10.0) (12.0) (12.2)(m)300Ó
235Ó
WIDE
TELE
27Ó
20Ó
320Ó
245Ó
MT1035+
MT830+/MT1030+
30Ó
25Ó 
						

							18
Using A Tabletop Or Cart
1. Place your LCD projector on a flat level surface at the optimal
distance from the screen or wall so you realize the size image you
want. (Avoid having bright room lighting or sun light directly on the
screen or wall where youll be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the projector
on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
4. Move the projector left or right to center the image horizontally on
the screen. (A)
5. To center the image vertically (B), lift the front edge of the projector
and press the buttons on the front of the projector, just above the
feet, to release the one-touch tilt feet. (There is approximately 10.5û
of up and down adjustment for the front of the projector. )
INSTALLATION33
34 6. If a trapezoidal distortion appears on the screen, use the KEY-
STONE button on the remote control or select Keystone from the
menu to correct the distortion.
If necessary, adjust the front or rear feet so that the lens surface is
parallel to the screen. If you use the projector with the screen tilted,
the picture will be distorted. Each of the rear feet height can be
changed up to 0.6 (4 mm).
7. Increase or reduce the size of the projected image by pressing the
Zoom (+) or (Ð) buttons on the remote control or top of the
cabinet.
(A) Top view
(B) Side view
screen
screen 
						

							19
35
36
Distance Chart
AC
D E
MT830+/MT1030+
Formulas(mm)
H (mm) =Horizontal Screen Width
M=1.25H/33.02(Projection magnification)
A=C/cosa
C (WIDE)=53.22M-85.609
C (TELE)=C(WIDE)21.3055
D ={(3H/8)-(92.2+8M)}
    =1.906M-92.2
E=92.2+8M
Formulas(inch)
H (inch) =Horizontal Screen Width
M=1.25H/1.3(Projection magnification)
A=C/cosa
C (WIDE)=2.094452M-3.37
C (TELE)=C(WIDE)21.3055
D ={(3H/8)-(92.2+8M)}/25.4
   =(1.906M-92.2)/25.4
E=(92.2+8M)/25.4 A : Distance between the lens and the screen center
C : Horizontal throw distance between the screen surface and the lens
D : Vertical distance between the projector foot and the bottom of image
E : Vertical distance between the projector foot and the screen center
INSTALLATIONa
MT1035+
Formulas (mm)
H (mm) =Horizontal Screen Width
M=1.25H/ 33.02 (Projection magnification)
A=C/ cosa
C (WIDE) = 49.22MÐ72.789
C (TELE) = C (WIDE)21.31
D=1.9822MÐ91.9
E= 91.9+7.692M
Formulas (inch)
H (inch) = Horizontal Screen Width
M = 1.25H/ 1.3 (Projection magnification)
A = C / cosa
C (WIDE)= 1.937012MÐ3.37
C (TELE)= C (WIDE)21.31
D=1.9822MÐ91.9/ 25.4
E= (91.9 + 7.692M) / 25.4 
						

							20
37
38 Standard Zoom Lens (Wide)
a
b (sin= a)
g (cos= a)
Screen Size
HÐWidth
4 : 3 Diagonal
A
C
D
EDegree
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch9.0
0.16
0.99
32
813
40
1572
61.9
1552
61.1
-34
-1.32
339
13.38.9
0.15
0.99
48
1219
60
2400
94.5
2371
93.4
-4
-0.16
462
18.28.8
0.15
0.99
56
1422
70
2814
110.8
2781
109.5
10
0.41
523
20.68.8
0.15
0.99
64
1626
80
3228
127.1
3190
125.6
25
0.99
585
23.08.8
0.15
0.99
72
1829
90
3642
143.4
3600
141.7
40
1.57
646
25.48.7
0.15
0.99
80
2032
100
4056
159.7
4009
157.8
55
2.15
708
27.98.7
0.15
0.99
96
2438
120
4884
192.3
4828
190.1
84
3.30
831
32.78.7
0.15
0.99
120
3048
150
6127
241.2
6057
238.4
128
5.03
1016
40.08.7
0.15
0.99
144
3658
180
7369
290.1
7285
286.8
172
6.77
1201
47.38.6
0.15
0.99
160
4064
200
8197
322.7
8104
319.1
201
7.92
1324
52.18.6
0.15
0.99
192
4877
240
9853
387.9
9742
383.5
260
10.23
1570
61.88.6
0.15
0.99
216
5486
270
11096
436.8
10970
431.9
304
11.96
1755
69.1
Standard Zoom Lens (Tele)
INSTALLATION
8.6
0.15
0.99
240
6096
300
12338
485.7
12199
480.3
348
13.70
1939
76.4
a
b (sin= a)
g (cos= a)
Screen Size
HÐWidth
4 : 3 Diagonal
A
C
D
EDegree
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch6.9
0.12
0.99
32
813
40
2041
80.4
2027
79.8
-34
-1.32
339
13.36.8
0.12
0.99
48
1219
60
3118
122.7
3096
121.9
-4
-0.16
462
18.26.8
0.12
0.99
56
1422
70
3656
143.9
3630
142.9
10
0.41
523
20.66.8
0.12
0.99
64
1626
80
4194
165.1
4165
164.0
25
0.99
585
23.06.7
0.12
0.99
72
1829
90
4732
186.3
4699
185.0
40
1.57
646
25.46.7
0.12
0.99
80
2032
100
5270
207.5
5234
206.1
55
2.15
708
27.96.7
0.12
0.99
96
2438
120
6346
249.9
6303
248.2
84
3.30
831
32.76.7
0.12
0.99
120
3048
150
7961
313.4
7907
311.3
128
5.03
1016
40.06.7
0.12
0.99
144
3658
180
9575
377.0
9511
374.4
172
6.77
1201
47.36.6
0.12
0.99
160
4064
200
10651
419.3
10580
416.5
201
7.92
1324
52.16.6
0.12
0.99
192
4877
240
12804
504.1
12718
500.7
260
10.23
1570
61.86.6
0.12
0.99
216
5486
270
14418
567.6
14322
563.8
304
11.96
1755
69.16.6
0.12
0.99
240
6096
300
16032
631.2
15925
627.0
348
13.70
1939
76.4
MT830+/MT1030+