NEC Lt180 Portable Projector Users Manual

E-14
PC CONTROLCOMPONENT IN COMPUTER INVIDEO IN AUDIO IN
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L
AUDIO IN
AC IN
MONITOR OUT
COMPUTER IN
AUDIO OUTAUDIO IN
PHONE
PHONE
Audio cable (not supplied)
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type) IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type) RGB/VGA signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It
is recommended that you use a commercially avail-
able distribution amplifier if connecting a signal
cable...

E-15
2. INSTALLATION AND CONNECTIONS
To connect SCART output (RGB)
PC CONTROLCOMPONENT IN COMPUTER INVIDEO IN
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L
AUDIO IN
AC IN
MONITOR OUT
COMPUTER IN
AUDIO IN AUDIO OUT
Video equipment such as
DVD player
Commercially available SCART cable
Female
ADP-SC1
Projector
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are
required for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the...

E-16
2. INSTALLATION AND CONNECTIONS
Connecting an External Monitor
PC CONTROLCOMPONENT IN COMPUTER INVIDEO IN AUDIO IN AUDIO OUT
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L
AUDIO IN
AC IN
MONITOR OUT
MONITOR OUT 
RGB/VGA signal cable
(supplied)
RGB/VGA signal cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB
analog image youre projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use an RGB/VGA cable to...

E-17
AUDIO INLRAUDIO OUT
LR
COMPONENT OUT
YCbCr
PC CONTROLCOMPONENT IN COMPUTER INVIDEO IN AUDIO IN AUDIO OUT
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L
AUDIO IN
AC IN
MONITOR OUT
AUDIO IN
COMPONENT IN
Connecting Your DVD Player
Audio cable (not supplied) Audio Equipment
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a component video cable...

E-18
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
PC CONTROLCOMPONENT IN COMPUTER INVIDEO IN AUDIO IN AUDIO OUT
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L
AUDIO IN
AC IN
MONITOR OUT
S-VIDEO INAUDIO IN
VIDEO IN
Connecting Your VCR or Laser Disc Player
Audio equipment
Use S-Video or RCA cables to connect your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of your RCA or...

E-19
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables two-pin plug to the AC IN of the projector, and then connect the other
plug of the supplied power cable in the wall outlet.
2. INSTALLATION AND CONNECTIONS
CONTROL
COMPONENT IN COMPUTER INVIDEO IN AUDIO IN
S-VIDEO IN
R Cr/Pr Cb/Pb
Y
L/mono
AUDIO IN
MONITOR OUT
S
LAMP
STATUS
POWER
ON/STAND BY
AUTO
ADJ.
AC IN
CAUTION
Do not unplug the power cable from the wall outlet under any...

E-20
3. PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a pic\
ture onto the screen.
Turning on the Projector
NOTE:• The projector has two power switches: a main power switch and an ON/STAND BY button.• When plugging in or unplugging the supplied power cable, make sure that \
the main power switch is pushed to the off (O)
position. Failure to do so may cause damage to the projector.
To turn on the main power to the projector, press the Main Power...

E-21
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu operation.
If you want, you can select the menu language later. See Language on page E-37.
NOTE:  Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until thelamp lighting is stabilized.
When the Lamp mode is set to Eco, the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
* If the...

E-22
Selecting a Source
Selecting the computer or video source
Using the cabinet buttons
Press the SOURCE button.
LAMP
STATUS
POWER
AUTO
ADJ.ON/STAND BYSELECTSOURCE
VOLUMES-VIDEOVIDEO
AUTO ADJ.
NOISE RED.
COMPUTER
COMPONENT
ASPECT HELP
FREEZE PICTURE
NOTE: If no input signal is available, the projector will display a blue background (factory preset).
3. PROJECTING AN IMAGE (BASIC OPERATION)
Adjusting the Picture Size and PositionPlace your projector on a flat level surface and ensure that the projector...

E-23
Move the projector left to center the image horizontally on the screen.
3. PROJECTING AN IMAGE (BASIC OPERATION)
Adjustable Rear Foot Using the Adjustable Rear Foot
The adjustable rear foot provides the projector with a horizontal tilt adjustment.
If the projector is placed on an uneven surface, keep the projector level by pushing down the left or right rear part
of the top cabinet with both hands.
NOTE: A spacer is attached to the adjustable rear foot to provide stability.
Remove the spacer before...