NEC Lt100 Projector Users Manual

     WARNING
¥Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.
¥ Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41ûF (5ûC) and 95ûF (35ûC).
¥ Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
¥ Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the...

PC CONTROLVIDEO INPUT
RGB INPUT RGB OUTPUT
S-VIDEO VIDEO L(MONO)-R-AUDIOOUTPUTINTPUT
RGB RGBAUDIO AUDIO
REMOTE
CONTROL
Document Camera
VCR, Laser Disk Player or DVD Player
Wiring Diagram
To video, S-video, and audio
inputs on the projector
41
IBM VGA or Compatibles Macintosh or Compatibles 
(Desk top type)
Remote Mouse
Receiver PS/2 mouse adapter
(supplied)
Mac ADB adapter
(supplied)
INSTALLATION42
Pin adapter for Macintosh
(supplied)
DVD Player with Y/Cb/Cr output
Signal cable (supplied)
To mini D-Sub...

Connecting Your PC Or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync LT100 (XGA) Projector will enable you to project your computers screen image
for an impressive presentation. All of these following display standards are supported:
To connect to a PC, Macintosh or computer equipped with an XGA/SVGA/VGA adapter or compatible graphics adapter, simply:
1. Turn off the power to your projector and computer.
2.
If your PC does not support XGA/SVGA/VGA you will need to install...

Settings for Monitor Mode
Number of DIP switch
Monitor size
15Ó multi-scan mode /16ÓÐ13Ó
17Ó multi-scan mode /19ÓÐ13Ó
19Ó multi-scan mode /21ÓÐ13Ó
13Ó fixed mode /6402480
VGA/SVGA mode
16Ó fixed mode /8322624
19Ó fixed mode /10242768
45
INSTALLATION46
S1
ON
ON
ON
ONS2 S3 S4
ONS5
ON
ONS6
ONS7
ONS8
ON
NOTE: For setting other than display modes supported by your Macintosh and LT100, using of the DIP
switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the 13Ó...

Changing Video Resolutions
Depending on your computers graphic capability, you may be able
to select one of several resolutions. Generally a computer- either a
PC or Macintosh- with 1 meg. of memory will run:
6402480 at 16.7 million colors (24 bit Truecolor)
8002600 at 65 thousand colors.
10242768 at 256 colors.
As the resolution increases,  the number of colors you can run de-
creases.  With 2 meg. of memory a computer will run:
6402480 at 16.7 million colors (24 bit Truecolor).
8002600 at 16.7 million...

Connecting Your DVD Player
You can connect your MultiSync LT100 Projector to a DVD player with the component outputs or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output use the optional 15-pin-to-RCA23 cable to connect your DVD player to the
RGB INPUT connector on the LT100.
For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite VIDEO...

Connecting Your Remote Mouse Receiver
The remote mouse receiver enables you to operate your computers mouse functions from the NEC MultiSync LT100
remote control. It is a great convenience for clicking through your computer-generated presentations.
To connect the remote mouse receiver:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the serial cable from the remote mouse receiver to your PCs
mouse port. (Use the 6-pin adapter for connecting to a PS/2 computer.)
For Macintosh:...

mThe Remote Mouse Receiver as a mouse for your computer
INSTALLATION
53
54
Serial cable (supplied)
Serial cable
(supplied)Remote cable
(supplied)Remote Control
Output
mThe Remote sensors on the projector cabinet work as
the remote sensor on the Remote Mouse Receiver
mYou can daisy-chain as many as five projectors and operate them with the same remote control.
To do so:
1. Turn off your computer.
2. Use the remote control cables supplied to connect the Remote Control Output of one
projector to the Remote...

This section describes how to select a computer or video source and how to adjust the
picture and sound.
General Controls Before you turn on your MultiSync LT100 Projector,  ensure that
the computer or video source is turned on and that your lens cap is removed.
1.Turn On The Projector The main power switch is on the back panel of the
MultiSync LT100 Projector. By turning this switch on, the projector will go into its
standby mode and the power light will glow amber. Only after you press the On
button on...

Using The Menus
1. Press the Menu button on the remote control or projector cabinet to display the Main Menu.
2. Press the Select button on the projector cabinet or (s) (t) buttons on your remote control to highlight the menu for the item you want
to adjust.
3. Press the Enter button on the projector cabinet or the Left Click button on the remote control to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using the Adjust (+) or (Ð) buttons on the remote control or...