NEC Location Status Installation Guide

LOCATION STATUS INFORMATION
INSTALLATION GUIDE
NEC America, Inc.
NDA-30043-002
Revision 2.0
March, 1997
Stock # 241716 

LIABILITY DISCLAIMER
NEC America reserves the right to change the specifications,  functions, 
or features in this document at any time without notice.  NEC America 
has prepared this document for use by its employees and customers.  The 
information contained herein is the property of NEC  America and shall 
not be reproduced without prior written approval from NEC America.
Copyright 1996
NEC America, Inc. 

NDA-30043  Revision 2.0Page i
Location Status Information - Installation Guide CONTENTS
TABLE OF CONTENTS
Page
Chapter 1 - Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1
Chapter 2 - Application Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   3
Step 1 – Application Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Step 2 –...

Page iiNDA-30043  Revision 2.0
CONTENTS Location Status Information - Installation Guide
This Page Left Blank. 

NDA-30043   Revision 2.0Page 1
Location Status Information - Installation Guide Introduction
Chapter 1 Introduction
This guide provides specific field entries that need to be made in the process of 
installing and configuring Location Status Information.  In addition to this guide, 
use the following manuals for this installation:
•Applications Manager (APM) Installation Manual – Contains step-by-step 
instructions for installing the software from the release media.
Applications Manager (APM) Operations...

Page 2NDA-30043   Revision 2.0
Introduction Location Status Information - Installation Guide
 
LOCATION  STATUS  INFORMATION 
INSTALLATION  REQUIREMENTS
Discussed in
Chapter 1
Introduction
Chapter  2
Chapter  3
Chapter  4
Chapter  5Software Installation
Software Release Media
Application Configuration
Application Characteristics
Primary Parameter Configuration 
OAI Facilities (Optional)
OAI Configuration Parameters (Optional)
User-Defined Parameters
Database Requirements
Master File Definitions
Master...

NDA-30043   Revision 2.0Page 3
Location Status Information - Installation Guide Application Configuration
Chapter 2 Application Configuration
Location Status Information is set up in the APM system using the Add function 
of the Application Configuration option on the APM System Administration menu:
1. Enter the APM option from the APM Platform Management Menu.
2. Enter the System Administrator password at the APM password screen.  
3. Enter the Application Configuration option from the System...

Page 4NDA-30043   Revision 2.0
Application Configuration Location Status Information - Installation Guide
Step 2 – Primary Configuration Parameters
On the APM Configuration Entry screen, make the following entries  for  the 
parameters shown below:
 
Step 3 – Facilities
According to instructions in the APM Operations Manual, designate the following  
facilities for Location Status Information using the Facilities command on the 
APM Configuration Entry screen:
MRFI Mode Release Facility (I) SCF Switch...

NDA-30043   Revision 2.0Page 5
Location Status Information - Installation Guide Application Configuration
Step 4 – Secondary OAI Configuration Parameters
Note:
Entries for parameters that are marked with an asterisk (*) should be made ex-
actly as shown.  All other entries in this section serve as examples only.
Using the OAI-Conf command on the APM Configuration Entry screen, make the 
entry shown for each of these parameters required by Location Status 
Information.  Use the instructions provided for...

Page 6NDA-30043   Revision 2.0
Application Configuration Location Status Information - Installation Guide
Step 5 – User-Defined Parameters
Make these parameter entries for LSI installation through the UserDefined 
command on the APM Configuration Entry screen:
This completes the configuration of Location Status Information in the APM.  
Refer to Database Requirements for information on how to create its database 
support.
Make this parameter entry for AMS_to_LSI installation through the UserDefined...