NEC LCD8205, LCD8205-P Owners Guide

User’s Manual
MultiSync LCD8205
MultiSync LCD8205-P 

Index
Declaration of conformity ........................................................................\
..................................................... English-1
Important Information ........................................................................\
.................................. ......................... English-2
Warning, Caution ........................................................................\
....................................... ................. English-2
Declaration...

English-1
EnglishFor USA
FCC Information
1. Use the attached specified cables with the MultiSync LCD8205 (L828N0)/\
MultiSync LCD8205-P (L828N0) color display so asnot to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC complianc\
e.
(2) Please use the supplied shielded video signal cable.
Use of other cables and adapters may cause interference with radio and t\
elevision reception.
2. This equipment has been tested and found to comply...

English-2
Important Information
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROMWALL SOCKET. TO FULLY DISENGAGE...

English-3
EnglishFOR OPTIMUM PERFORMANCE, PLEASE NOTE THEFOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR:
• DO NOT OPEN THE MONITOR . There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage...

English-4
Contents
Power Cord*1
Setup Manual
DVI-D to DVI-D cable
Wireless Remote Controland AAA  Batteries
Clamp
Your new MultiSync LCD monitor box* should contain the following:
• LCD monitor
• Power Cord*
1
• Video Signal Cable
• Setup Manual
• Wireless Remote Control and AAA Batteries
• Clamp
• Screw for clamp (M4 x 10) x 2
• CD-ROM
• Eyebolt x 2
• Washer x 2
• Hanger bolt x 8
CD-ROMScrew for clamp
(M4 x 10) x 2
*1Type and number of power cords included will depend on the where the LCD \
monitor is...

English-5
EnglishThis device cannot be used or installed without the TabletopStand or other mounting accessory for support. For properinstallation it is strongly recommended to use a trained,NEC authorized service person. Failure to follow NECstandard mounting procedures could result in damage to theequipment or injury to the user or installer. Product warrantydoes not cover damage caused by improper installation.Failure to follow these recommendations could result invoiding the warranty.
Mounting
DO...

English-6
4. Attach Mounting Accessories
The display is designed for use with the VESA mounting
system.
When using mounting accessories other than NEC
compliant and approved, they must comply with the VESA-
compatible mounting method. NEC strongly recommends
using screws M8 size and 10 - 18 mm in length. If using
screws longer than 18 mm, check the depth of the hole.
(Recommended Fasten Force: 1125 - 1375N•cm)
NEC recommends using a mounting interface that complies
with UL1678 standard in North...

English-7
English
1 POWER button ()
Switches the power on/off.
2  CH +/- button
Acts as 
  button to move the highlighted area up or down
to select adjustment items within OSD menu.
3  VOL +/- button
Increases or decreases audio output level.
Increases or decreases the adjustment level within OSD
menu settings.
4  SEL button
Enter Input Source OSD menu, [DVI], [PC], [HDMI], [AV1],
[AV2], [S-Video] and [Component].
5  MENU button
Activates the OSD menu when the OSD menu is turned-off.
Move to previous...

English-8
Terminal Panel
1 HDMI connector
To input digital HDMI signals.
2 DVI IN (DVI-I)
To input digital or analogue RGB signals from a computer.
3 SPDIF
Optical digital audio out for HDMI input only.
4 EXTERNAL CONTROL (D-Sub 9 pin)
Connect RS-232C input from external equipment such as a
PC in order to control RS-232C functions.
5 Audio Input (for DVI-I connector)
To input audio signal from computer.
6 Component (RCA)
Connecting equipment such as a DVD player, HDTV device
or Set-Top-Box.
7 AV 1
AV1:...