NEC Ht1100 Entertainment Projector Users Manual

E-31
When screen size 4:3 is selected for the source, the following selections will display.
Normal
Zoom
Cinema
V-Zoom
modeinput
480i/576iDVD progressive 480p/576p 720p 1080i 1080p PC(RGB)
These are the same signals.
Normal
Full
Zoom
Stadium
modeinput
480i/576iDVD progressive 480p/576p 720p 1080i 1080p PC(RGB)
These are the same signals.
When screen size 16:9 and Anamorphic (*) are selected for the source, the following selections will display.
* A commercially available anamorphic lens is needed. 

E-32
Masking Unwanted Area [Blanking]
This feature allows you to mask any unwanted area of the screen im-
age.
Adjust the Top, Bottom, Left or Right blanking with the SELECT  or 
button.
Adjusting Position and Clock [Position / Clock]
This allows you to manually adjust the image horizontally and vertically,
and adjust Clock and Phase.
Horizontal/Ver tical Position:
Adjusts the image location horizontally and ver tically using the SE-
LECT  and  buttons.
Clock .............. Use this item to fine tune...

E-33
The following buttons are not available for the currently projecting sig-
nals:
1) The Cut and Paste buttons on the Entry Edit Command screen
2) The Input Terminal button on the Entry Edit screen
NOTE: When all the signals in the Entry List are deleted, the currently projectedsignal will be also deleted except locked signals.
Setup [Page 1]
Selecting Aspect Ratio and Position for Screen [Screen]
Screen Type:
Select one of three options: 4:3 Screen, 16:9 Screen or Anamorphic
for the screen to be...

E-34
Setting Auto Adjust
This feature sets the Auto Adjust mode so that the RGB image can be
automatically or manually adjusted for noise and stability. You can auto-
matically make adjustment in two ways: Normal and Fine
Off .................. The RGB image will not be automatically adjusted.
You can manually optimize the RGB image.
Normal ........... Default setting. Normally select this option.
Fine ................Select this option if fine adjustment is needed. It takes
more time to switch to the...

E-35
Gateway:
Set the default gateway of the network connected to the projector.
Press 
 to display the software keyboard and type in 12 numeric
characters. Checking this box will make the set default route valid.
When data is sent from the LAN card, the transfer location will be
searched according to the previously set routing information; how-
ever, when the transfer location has not been found as a result of the
search, the data will be sent to the device that holds the IP address
set here. The IP...

E-36
Status:
Displays the status of the LAN settings.
IP Address ..... Indicates the IP address of the projector.
Subnet Mask .. Indicates the subnet mask of the projector.
Gateway ......... Indicates the gateway of the network connected to
the projector.
MAC Address . Indicates the MAC address of the LAN card.
Reconnect ..... Use this button to connect the projector to a network.
Security
The Security function enables you to protect your projector so that the
projector will not project a signal unless...

E-37
•The security disable mode is maintained until the main power is
turned off (by setting the main power switch to O or unplugging
the power cord). In the following cases you will be asked to check
the protect key or input the keyword:
(1) When OK is selected at an image for which security is set
and the power is turned off then back on
(2) When the main power is turned off then back on while the
security function is enabled
(3) When you attempt to display an image for which security is
set while the...

E-38
USING THE VIEWER
PC CONTROL
RGB IN SG TRIGGER
VIDEO IN S-VIDEO INS-VIDEO S-VIDEO
RGB/DVI RGB/DVI VIDEO VIDEO
AUDIO IN AUDIO INCOMPONENTYCb/Pb
Cr/Pr
Removing the PC Card
Press the eject button. The PC card pops out a little. Grasp the edges
of the PC card and pull it out.
NOTE: Do not eject the PC card while its data is being accessed.
Eject button
Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the PC
card slot in a specific direction. It cannot be...

E-39
Operating the Viewer Function from the
Projector (playback)
This section describes the operation for showing slides created using
the Viewer function with the projector. It is also possible to make slides
directly from the images projected with the projector.
Projecting slides (Viewer)
Preparation: Use the Capture feature to store JPEG or BMP files in a
PC card inserted into the projector’s slot. Or store JPEG or BMP files in
a PC card inserted into your PC’s slot.
1. Insert a PC card into the PC...

E-40
Storing Images Displayed on the Projector on the PC
card (Capture)
The Capture features allows you to capture an image from a source that
is currently being displayed. The image is saved as JPEG in the PC
card.
NOTE:
*Signals from DVI input are not possible to be captured.
*Unless a PC card is inserted into the PC Card slot of the projector, the Capture
feature is not available.
*The Card Error display means that the free space of the PC card is insufficient
for saving images. Make more space...