NEC Gt2000r Lcd Projector Users Manual

							E-31
Operating Multiple Projector with Remote Control
You can operate as many as 64 projectors with the same remote control in wireless operation.
To do so:
1. Select [Settings Menu]®[Projector ID] under the main menu and assign an ID number to each projector.
2. Specify the remote ID number to the projector to be used. To do, press and hold the CTL and press Adr button to enter the ID
number.
You can operate the projector assigned the same ID number as the remote address.
Projector ID= 01Projector ID= 02 Projector ID= 03
Remote Address = 03
You can daisy-chain as many as 64 projectors and operate them separately with the same remote control in wired operation.
To do so:
Use the remote control cable supplied to connect the Remote Control Output of one projector to the Remote Control Input of the next
until all the projectors are connected.
REMOTE 2/PC
EXT
-CTLREMOTE
OUTPUT REMOTE
INPUT
Projector ID= 01Projector ID= 02 Projector ID= 03
Remote Address = 03 
						

							E-32
EX CO
8/
EX C1
EXT-CTL3
15
EX ENPOWER
14
EX PW
1ch
2ch 3ch 5
Console Control Unit Setup Example
* This example is when power is ON and channel 1, 2, and
3 switching is activated. The circuit setup is valid when
the contacts of any of the switches are closed.
Small signal Silicone diodes are used.
* Switchs cannot be pressed simultaneously.
* Channel number means slot number on the ISS-6020.
EMOTE 1B 1 AUDIO
REMOTE 2/PC
EXT-CTLREMOTE
OUTPUT REMOTE
INPUT NO R
51423
10
11 12 13 14 156 978
External Control
To turn your projector on and off, to turn the mute on or off and to switch video sources, use the EXT-CTL connector.
* When using the external control, do the following:
1. Select the [Settings Menu]®[Ext.Control] under the main menu and select On.
2. Set the pin 8 of the DIP switch (S8601) to SHORT. The DIP switch is located inside the ISS-6020 system control module.
External equipment
(Max.10 units)
To Slot 1-10 Video Signal
ISS-6020Video Signal
To REMOTE 1 To REMOTE 1
Control Cable
EXT-CTL Pin Assignments
Pin No. SignalName Function
15 Signal Ground Ground
14 EX EN External control enable
5 EX PW Power ON/OFF
10 EX MT Mute ON/OFF
8 EX C/O Source selection data bit
3 EX C1 Source selection data bit
9 EX C2 Source selection data bit
4 EX C3 Source selection data bit
11 EX C4 Source selection data bit
13 EX C5 Source selection data bit
12 EX C6 Source selection data bit
1,2,6,7 Not connected Not used
Control Method
When the EX EN signal is low, the projector periodically polls the setting data.
Period of external control validity
(300 ms or more)
EX EN
Hi
Lo 
						

							E-33
Setting The Data
When the EX PW pin is low, the power is on; when high, the
power is off.
When the EX MT pin is low, Picture Mute is on; when high,
Picture Mute is off.EX PW
Low
High Power
ON
OFF
Note: Channel settings are only valid when the ISS-6020 is connected.
Note: If a channel is switched to another using the remote control when the external control is valid, the channel is forced to switch to
the one set by the external control.
Connecting A Single ISS-6020 Switcher
Slot
1
2
3
4
5
6
7
8
9
10Channel Number
1
2
3
4
5
6
7
8
9
0EX C6
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
HiEX C5
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
HiEX C4
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Hi
HiEX C3
Hi
Hi
Hi
Hi
Hi
Hi
Hi
Lo
Lo
HiEX C2
Hi
Hi
Hi
Lo
Lo
Lo
Lo
Hi
Hi
HiEX C0
Lo
Hi
Lo
Hi
Lo
Hi
Lo
Hi
Lo
Hi EX C1
Hi
Lo
Lo
Hi
Hi
Lo
Lo
Hi
Hi
Hi
Connecting Multiple ISS-6020 Switchers
Master Slot
1
1
1
1
9
9
9
10
10
10
10Slave Slot
1
2
3
4
8
9
10
1
2
9
10Channel Number
11
12
13
14
98
99
90
01
02
09
00EX C6
Hi
Hi
Hi
Hi
Lo
Lo
Lo
Hi
Hi
Hi
HiEX C5
Hi
Hi
Hi
Hi
Lo
Lo
Hi
Hi
Hi
Hi
HiEX C4
Hi
Hi
Hi
Hi
Hi
Hi
Lo
Hi
Hi
Hi
HiEX C3
Lo
Lo
Lo
Lo
Hi
Hi
Lo
Hi
Hi
Lo
HiEX C2
Hi
Lo
Lo
Lo
Hi
Hi
Hi
Hi
Hi
Hi
HiEX C1
Lo
Hi
Hi
Lo
Lo
Lo
Lo
Hi
Lo
Hi
HiEX C0
Lo
Hi
Lo
Hi
Hi
Lo
Hi
Lo
Hi
Lo
Hi
To calculate:
EX C6-EX C0  can be presented in binary; Lo=1 and Hi=0
Convert a decimal number (channel number) to the binary number.
Example: Channel number14 (master 1 and slave 4)=23 + 22+ 21. Set C3, C2 and C1 to Lo.
In other words 14=26 x 0 + 25 x 0 + 24 x 0 + 23 x 1 + 22 x 1 + 21 x 1 + 20 x 0
Therefore you will get C6=Hi, C5=Hi, C4=Hi, C3=Lo, C2=Lo, C1=Lo, C0=Hi
EX MT
Lo
Hi Picture Mute
ON
OFF 
						

							E-34
OPERATION4
(OFF) (ON)
STATUS
POWER
ON / OFF
STATUS
POWER
ON / OFF
OFF
ON POWER
RGB1 RGB2VIDEO/S-VIDEO
Each press toggles between S-
VIDEO and VIDEO.
VOLUME
The volume increases.
The volume decreases.
Volume
Ð+  32
General Controls
Getting started
This section describes the basic operation of the projector.
The operation may differ depending on the makeup of the
projector system; therefore, please follow the directions of
your system administrator.
Operation using the remote control is described here. The
following controls have the same function: the MENU button
of the main unit and that of the remote control, the SELECT
button of the main unit and the cursor button of the remote
control, the ENTER button of the main unit and the ENTER
button of the remote control.
1. Switch On the Main Power
Press the 1 side of the POWER switch located on the front
of the main unit.
The POWER indicator will light up orange and the unit will
be set to the standby mode.
When the STATUS indicator is lit or flashing, see Page E-77.
2. Switch On the Power

Press the POWER (ON/OFF) button.
The lit POWER indicator will change to green and the power
will be switched on.

Press the POWER ON button.
3. Select the Input

Select the desired input connector.
Directly specify and call the list of user memories in which
the input signals and screen adjustment conditions have al-
ready been registered.
This function is valid when the on-screen menu is not dis-
played.
¥ Calling (Loading) Memory Lists 00 to 09
Hold down the CTL button and press the number keys
that correspond with the numbers.
(Remote control number buttons 0 through 9 correspond
with memory lists 00 through 09.)
¥ Calling (Loading) Memory Lists 00 to 99
Use the number buttons to enter the numbers that corre-
spond with the memory lists, then press the LOAD
button.
When an entry mistake has been made, press the
CLEAR button.
* See Data Reading of Registration Signals (Load) on Page
E-60 when loading signal data while viewing the contents
from the on-screen menu display as well as when loading the
switcher signal data.
4. Adjusting the Volume of the Built-in Speaker
A press of the button will display the volume display for a
while.
* To set the volume display so that it does not appear, see
Selecting the On-screen Display ON/OFF on Page E-37.
* When the unit is connected with a switcher and [Audio
Control] is set to [On], the volume button of the projector will
control the volume of the equipment that is connected to
AUDIO OUT of the switcher.
The volume adjustment range is from 0 to 63. 
						

							E-35
+
-
FOCUS ZOOM
W
T
OFF
ON POWER
STATUS
POWER
ON / OFF
(OFF) (ON)
STATUS
POWER
ON / OFF
5. Adjust the Screen Size and then Adjust the Focus
When the projector is set up permanently, there is no need to
make the usual adjustments.
(The Zoom and Focus buttons do not function on GT2000R.)
A) Press the ZOOM W/T button and adjust the screen size.
B) Press the FOCUS +/- button and adjust the focus.
6. Adjust the Screen and Picture (Only When Required)
When the screen is not displayed properly, adjust the screen.
When the tint of the picture or some other attribute is not
correct, adjust the picture. See Adjusting the Screen on
Page E-49 and Adjusting the Picture on Page E-44.
* When the input signal is selected with the user memory or
the channel memory and the auto memory save function is
set to [On], the adjustment data is overwritten.
See Storing the Adjustment Data on Page E-59 for
information about registering the input signal and adjust-
ment data that are currently being projected.
NOTE: Selecting the Slot Directly When the ISS-6020 Is
Connected
When the ISS-6020 switcher is connected, the slot (channel)
of the switcher can be directly specified. (Valid when the on-
screen menu is not displayed)
When one switcher is connected
Enter the channel number with the number button of the
remote control, then press the ENTER button.
When two or more switchers are connected
Enter the two-digit channel number with the number buttons
of the remote control, then press the ENTER button.
See Selecting the Various Items and Switchers on Page E-
58 for information about master switcher and slave switcher
number specification.
7. Switch Off the Power

A) Press the POWER OFF button.
The STATUS indicator will flash in green for 1 minute
(and will be displayed while the cooling fan is turning).
The color of the POWER indicator will change to orange
(indicating the standby mode).
B) Press the POWER button for at least 2 seconds. The
Power Off message will be displayed.
* The cooling fan will continue to turn for about 1 minute
after the power has been switched off. During this period, it
will not be possible to switch on the power again.
8. Switch Off the Main Power
Press the 0 side of the POWER switch located on the front
of the main unit.
Also switch off the power to the equipment that is connected
to the projector.
Note: Do not switch off the main power before the fan has
stopped. It will cause damage.
Main Menu
Picture
Alignment
Memory
Switcher
Display Menu
Settings Menu
Source
Source
RGB1
RGB2
Video
S-Video 2. Select [Source] of the main menu and press the ENTER
button. The source selection display will appear.
3. Press the cursor s/t button and select the target input
connector (source), then press the ENTER button to set.
On-screen Input Selection
Input selection is also permitted with the on-screen menu.
1. Press the MENU button to display the main menu. 
						

							E-36
Main Menu
Picture
Alignment
Memory
Switcher
Display Menu
Settings Menu
SourceSettings Menu
Language
Background
Auto Start
Auto Save
Onscreen Mute
Switcher Control
Ext. Control
Projector ID
Sync Termination
Projection
Keystone
Keystone Save
English
Currently selected
item Setting at Time of
Factory Shipping
English
Blue back
Off
Off
Off
Standalone
Off
00
Hi-impedance
Front Floor
00
Off
Language
English
Deutsch

Italianno
Espanol
Svenska
SETUP (Various Settings)
Please make settings in conjunction with both the projector and the system.
NOTE: To accommodate worldwide use of the projector, the default language setting for the projector is English. See below for the
detailed setting procedure. Descriptions given here assume that the language setting of the unit has already been set to English.
Default Settings of the Settings Menu
The unit is set as described below before it is shipped from the factory.
Please set any required items.
Press the MENU button to display [Main Menu], then select [Settings Menu] with the cursor button and press the ENTER button
to display the various settings.
Selecting the On-screen Language
[Language]
This is the language selection for the display characters of
the on-screen menu and other displays.
1. Select [Settings Menu] ® [Language] from the main menu.
2. Press the cursor s/t button and select the language, then
press the ENTER button to set.
To turn off the on-screen menu display, press the
MENU button.
The display will return to the main menu. Press the
MENU button again to turn off the on-screen
menu. 
						

							E-37
Background
Blue
Black
Auto Start
On
Off
Auto Save
On
Off
Onscreen Mute
On
Off
Selecting the Background Color When There Is
No Signal [Background]
This is the setting of the background color when there is no input
signal.
1. Select [Settings Menu] ® [Background] from the main menu.
2. Press the cursor s/t button and select the background color, then
press the ENTER button to set.
Blue...The background color will be blue.
Black...The background color will be black.
Selecting Auto Start [Auto Start]
When the main power switch is set to ON, this function switches
on the power without the need to press the power button.
1. Select [Settings Menu] ® [Auto Start] from the main menu.
2. Press the cursor s/t button and select On/Off, then press the
ENTER button to set.
On ....The projector will start up when the main power is
switched on.
Off ....The projector will enter the standby mode when the
main power is switched on.
Selecting the Automatic Memory Save Function
[Auto Save]
This function automatically saves the adjustment conditions to the
memory in use when screen adjustments or picture adjustments are
performed while projecting the image of the input equipment using
user memory or channel memory.
The auto save function saves the information when the MENU and
ENTER buttons are used upon exiting from the various adjustment
menus.
1. Select [Settings Menu] ® [Auto Save] from the main menu.
2. Press the cursor s/t button and select On/Off, then press the
ENTER button to set.
On .... Auto memory saves are enabled.
Off .... Auto memory saves are disabled.
Selecting the On-screen Display ON/OFF
[On-screen Mute]
This is a selection of whether or not to show displays other than on-
screen menu displays (such as simple condition displays, the ad-
justment bar which is displayed when the remote control VOL-
UME button is used to make an adjustment, and when switching
the input signal).
1. Select [Settings Menu] ® [On-screen Mute] from the main menu.
2. Press the cursor s/t button and select On/Off, then press the
ENTER button to set.
On ....Displays will be muted.
Off ....Displays will not be muted. 
						

							E-38
The term switcher refers to the NEC ISS-6020 Switcher.
Switcher Control
Standalone
SW 1 Level
SW 2 Level
Ext. Control
On
Off
Projector ID
No.0 - 64
Selecting the Switcher Control Method [Switcher
Control]
The switcher is a unit that switches the input equipment when a
number of different video devices or computers are connected.
When the REMOTE 1 connector is used, input selection and
adjustment are permitted by the projector. See Using User
Memory and Channel Memory on Page E-56.
See (Connections with the ISS-6020) on Page E-28 for informa-
tion about connections.
1. Select [Settings Menu] ® [Switcher Control] from the main menu.
2. Press the cursor s/t button and select the switcher connection
condition, then press the ENTER button to set.
Settings will become effective the next time the power is switched
on.
Standalone.......The projector used in stand alone opera-
tion.
SW 1 Level .......The projector used with one Switcher.
SW 2 Level .......The projector used with two or more
Switchers.
Selecting External Control Connections Settings
[Ext. Control]
When using the EXT-CTL connector of the projector, set the
external control setting to [On].
1. Select [Settings Menu] ® [Ext. Control] from the main menu.
2. Press the cursor s/t button and select On/Off, then press the
ENTER button to set.
On ....Enables the EXT-CTL connector.
Off ....Disables the EXT-CTL connector.
Setting the Projector ID Number [Projector ID]
Set identification numbers to the projectors when operating a
number of projectors (GT2000/GT2000R) by remote control or
when controlling a number of projectors by personal computer.
1. Select [Settings Menu] ® [Projector ID] from the main menu.
2. Enter the ID number with the number buttons, then press the
ENTER button to set.
[00] will be set when using one projector.
When using a number of projectors, set [01] to [64].
¥ To delete the entry, press the CLEAR button of the remote control.
The setting will return to [00].
When operating a number of projectors by remote control, also set
the address of the remote control. See Setting of the Remote
Control Address on Page E-43.
Setting the ID of the projector to [00] permits remote control
operation irrespective of the ID of the remote control. 
						

							E-39
Sync Termination
75W
Hi-Z
Projection
Front Floor
Rear Ceiling
Rear Floor
Front Ceiling
Sync Signal Termination Setting
[Sync Termination]
This sets the impedance of the RGB/YCbCr Input 1 connector.
This function sets whether or not the unit will accommodate a 75
ohm output (specification) impedance of the video or personal
computer equipment.
1. Select [Settings Menu] ® [Sync Termination] from the main
menu.
2. Press the cursor s/t button and select the termination resistance
value, then press the ENTER button to set.
75 ohms...........................When the impedance of the out-
put connector of the connected
equipment is 75 ohm.
High Impedance (Hi-Z).....When the impedance of the out-
put connector of the connected
equipment is not 75 ohm.
To turn off the on-screen menu display, press the MENU button.
The display will return to the main menu. Press the MENU button
again to turn off the on-screen menu.
Selecting the ProjectorÕs Projection Method [Pro-
jection]
This selection of the projection method is made to suit the usage
conditions.
Model GT2000 is designed for front projection and model
GT2000R is designed for rear projection.
1. Select [Settings Menu] ® [Projection] from the main menu.
2. Press the cursor s/t button and select the target projection, then
press the ENTER button to set.
Front floor..............When the projector is placed on a table
and projects from the front
Rear ceiling............When the projector is suspended from
the ceiling and projects from the rear
Rear floor...............When the projector is placed on a table
and projects from the rear
Front ceiling...........When the projector is suspended from
the ceiling and projects from the front 
						

							E-40
[Keystone distortion] [No distor tion]
Keystone Save
On
Off Settings Menu
Language
Background
Auto Start
Auto Save
Onscreen Mute
Swithcer Control
Ext. Control
Projector ID
Sync Termination
Projection
Keystone
Keystone Save
Ð+  Ð10
Normalize?
Keystone
Ye s
No
Selecting Correction and Storage of Keystone
Distortion [Keystone]
Keystone distortion arises when the angles are off between the
projector and screen in the vertical orientation at the time of setting
up the projector. The keystone function is used in this distortion
adjustment.
When the setting is permanent, setting the keystone save function
to On will enable projection using this adjustment value from the
next occasion.
¥ Adjusting Keystone Adjustment [Keystone]
1. Select [Settings Menu] ® [Keystone] from the main menu.
The adjustment bar will be displayed.
2. Press the cursor § (Ð) / © (+) button and adjust so that the left and
right sides are parallel.
NOTE: This function will not work when the input signal is not
present. If this is the case, apply an signal and make the adjusment on
it.
¥ Setting Keystone Save [Keystone Save]
1. Select [Settings Menu] ® [Keystone Save] from the main menu.
2. Press the cursor s/t button and select On/Off, then press the
ENTER button to set.
On ....Enables the keystone correction value at starting
time.
Off ....Sets the keystone correction value to the default
value at starting time.
To return to the default value, press the NORMAL button of the
remote control.
Press the cursor s/t button and select [Yes], then press the
ENTER button to return to the default value.