NEC Electra 16/48 Executive Station Users Guide

l Lift handset, 
l Depress idle outside line button, 
l Dial desired telephone number. NOTE: When placing consecutive calls, the RECALL button 
may be used to disconnect existing call and to 
provide dial tone. 
PLACING-AN OUTSIDE CALL USING 
HANDSFREE DIALING ,, 
l Depress ON/OFF button. 
l Depress idle outside line button. 
l Dial desired telephone number, 
l Lift handset when called party’s voice is 
heard through speaker. 
(i-icmdset not required when equipped L 
with Speakerphone]. 
NOTE: If ‘busy”...

l Lift handset. (Depress ON/OFF b&ton if equipped with Spea&rphone.) 
l Depress ICM button. 
l Dial desired station number. 
*Voice announce after hearing tone burst. OR 
l Dial digit “1” to transmit tone signal if desired. NOTE: When calling a Single-Line telephone, no voice announcement is available. Ring signal will be automatically provided. 
NOTE: Called party may be programmed to receive tone signal rather than voice announcement. 
PLACING AN INTERCOM CALL USING STATION DSS BUTTONS 
l Lift handset...

SETTING CALLBACK REQUEST: 
l Call station and receive “no answer” or Call Waiting Tone. 
l Dial I’#“. 
*Verify at display: “SET” = accepted “DENIED” = denied. 
l If accepted, your station number will flash intermittently in the called keyset’s display, indicating 
your “Callback Request”. 
SETTING AUTOMATIC CALLBACK: 
l Call station and receive Call Waiting Tone. 
l Dial “0”. 
l Verify at display: “CALLBACK SET” = accepted “DENIED” = denied. 
l If accepted, you will receive tone signal when the called...

I,. , L..__... CALLS 
l Depress HOLD button, 
l Held outside line button will wink intermittently on your keyset. All other keysets will receive a 
on that line button, 
NOTE: When you place an intercom call on hold, the HOLD button will rapid-flash. 
PLACING CALLS ON EXCLUSIVE HOLD: 
l Depress HOLD button twice. 
l Held outside line button will wink intermittently on your keyset. All other keysets will receive a 
LED on that line button, 
NOTE: If a call remains on exclusive hold longer than a preset...

l Depress HOLD button. 
l Depress ICM button. 
l Dial desired station number. 
*Announce transfer, informing station which line to pick up. 
NOTE: When transferring a call to a station which does not have that line appearance, the following procedure must be used: l Depress HOLD button. l Depress ICM button. l Dial desired station number, wait for party to answer via handset and announce transfer. l Depress ADD/ON button. l Depress intermittently winking line button. l Confirm transfer and replace...

l Enter DSS or Speed Dial mode as desired by depressing ‘SPD” button. 
DSS = SPD LED unlit, Speed Dial = SPD LED lit. .e 
l Depress DSS/Speed Dial button to be verified (1-19) while keyset is idle. 
*Confirm number in display. 
l Lift handset or depress ON/OFF but-ton. 
l Depress idle outside line button, 
l Dial ‘I#” and two-digit access code (20-99). 
l When party answers, use handset to talk. (Handset not required when equipped with Speakerphone). 
Consecutive speed dialing has particular value when...

l Depress ON/OFF button or lift handset, 
l Depress ICM button. 
l Dial “67” for Voice Signalling. OR l Dial “68” for Tone Signalling. 
l Depress ON/OFF button or restore handset. NOTE: Default value is that all keysets are assigned VOICE SIGNALLING. 
l Depress ON/OFF button or lift handset, 
l Depress ICM button. 
l Dial “77”. 
l Depress CO/PBX line button to be assigned as Prime Line. 
LED IDLE-Prime Line not assigned. 
LED LIT-Prime Line assigned. 
l Depress ICM button, 
l Depress ON/OFF button or...

A THREE-PARTY CONFERENCE: 
l 
Establish first call. 
l Depress HOLD button, 
l Establish second call. 
l Depress ADD/ON button, 
l Depress held line button (or HOLD button for intercom call), NOTE:A three-party conference may consist of the following: 
3 internal stations 
2 internal stations + 1 outside line 
1 internal station + 2 outside lines. 
A FOUR-PARTY CONFERENCE: 
l 
Establish three-party conference as 
outlined above. 
l Depress HOLD button. 
l Establish third call. 
l Depress ADD/ON button....