NEC E552, E462, E422, E322 Users Manual
Have a look at the manual NEC E552, E462, E422, E322 Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
English-5English-4
Safety Instructions
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a\
Class B digital device, pursuant to Part 15 of the FCC Rule� These limits are designed to provide reasonable protection against harmful interference i\
n a residential installation� This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with\
these instructions, may cause harmful interference to radio communicatio\...](http://img.usermanuals.tech/thumb/54/93890/w64_E_Series_Manual_d-5.png "Page 6
English-5English-4
Safety Instructions
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a\
Class B digital device, pursuant to Part 15 of the FCC Rule� These limits are designed to provide reasonable protection against harmful interference i\
n a residential installation� This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with\
these instructions, may cause harmful interference to radio communicatio\...")
![Page 8
English-7English-6
Batteries installed warning
Caution - Danger of explosion if batteries are incorrectly replaced� Replace only with the same or equivalent type� The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other \
than that contained in the operating instructions unless you are qualified to do so....](http://img.usermanuals.tech/thumb/54/93890/w64_E_Series_Manual_d-7.png "Page 8
English-7English-6
Batteries installed warning
Caution - Danger of explosion if batteries are incorrectly replaced� Replace only with the same or equivalent type� The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other \
than that contained in the operating instructions unless you are qualified to do so....")
![Page 9
English-7English-6
English
Installed with stand
4 inches10 cm4 inches10 cm
Leave at least this space
around the set.
11 7/8 inches
30 cm
4 inches10 cm
Never install the TV set where Air circulation is blocked�
Objects and ventilation holes
Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result \
in a fire or an electric shock. Do not place any objects on the TV.](http://img.usermanuals.tech/thumb/54/93890/w64_E_Series_Manual_d-8.png "Page 9
English-7English-6
English
Installed with stand
4 inches10 cm4 inches10 cm
Leave at least this space
around the set.
11 7/8 inches
30 cm
4 inches10 cm
Never install the TV set where Air circulation is blocked�
Objects and ventilation holes
Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result \
in a fire or an electric shock. Do not place any objects on the TV.")
![Page 13
English-11English-10
English
Attaching the Base
E322 / E422 / E462E552
1� Place the display face down on a soft and flat surface to prevent scratching and damage�
2� Carefully align the base to the stand and fasten the screws with a cross\
-head screwdriver�
CAUTION: The base of the stand is very heavy � Install with care to avoid injury such as dropping the base onto one's foot�
Place The Display On A Solid Surface
Ensure that the LCD display is placed in a position to allow free flow of air � Do...](http://img.usermanuals.tech/thumb/54/93890/w64_E_Series_Manual_d-12.png "Page 13
English-11English-10
English
Attaching the Base
E322 / E422 / E462E552
1� Place the display face down on a soft and flat surface to prevent scratching and damage�
2� Carefully align the base to the stand and fasten the screws with a cross\
-head screwdriver�
CAUTION: The base of the stand is very heavy � Install with care to avoid injury such as dropping the base onto one's foot�
Place The Display On A Solid Surface
Ensure that the LCD display is placed in a position to allow free flow of air � Do...")
![Page 15
English-13English-12
English
Connect To The Power Source
The display should be installed close to an easily accessible power outl\
et� Fully insert the prongs into the power outlet socket� A loose connection may cause image degradation�
If there is power to the display, the front LED at the bottom of the display will be either blue or red� A blue LED means the display is powered on� A red LED means the display is in standby mode�
Power On/Off Your New LCD Display
Press the power key on the remote control...](http://img.usermanuals.tech/thumb/54/93890/w64_E_Series_Manual_d-14.png "Page 15
English-13English-12
English
Connect To The Power Source
The display should be installed close to an easily accessible power outl\
et� Fully insert the prongs into the power outlet socket� A loose connection may cause image degradation�
If there is power to the display, the front LED at the bottom of the display will be either blue or red� A blue LED means the display is powered on� A red LED means the display is in standby mode�
Power On/Off Your New LCD Display
Press the power key on the remote control...")
English-9English-8 English 3� following procedures: • Reorient or relocate the receiving display� • Increase the separation between the equipment and display � • Connect the equipment into a different outlet than the receiver � • Consult your dealer or an experienced radio/display technician for assistance� If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “\ How to Identify and Resolve Radio-display Interference Problems�” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No� 004-000-00345-4� Windows is a registered trademark of Microsoft Corporation� NEC is a registered trademark of NEC Corporation� All other brands and product names are trademarks or registered trademar\ ks of their respective owners� ® HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and \ other countries�
English-11English-10 Preparation IMPORTANT: Do not apply pressure to the screen display area which may compromise the integrity of the display� The manufacturer’s warranty does not cover user abuse or improper installations� Preparing Your LCD Display For Wall Mounting We suggest that you keep your display at least 2�36 inches (60 mm) from the wall to prevent cable interference� Before mounting your display on the wall, you need to remove the base� For your safety, only mount with a UL listed wall mount bracket that supports the weight of the display � (Please see page 28 �) To attach a wall mount bracket to your display: E322 / E422 / E462 E552 E322 / E422 / E462E552 screen size (inches)required pitch (mm)require mounting bolts 32200 x 2004 x M6 42400 x 2004 x M6 46400 x 2004 x M6 55400 x 2004 x M6 1� E322/E422/E462: Loosen the screws on the bottom of the stand and base� E552: Loosen the screws on the back of the stand-base� 2� Remove the stand base from your display� 3� Secure the wall mount bracket to the back of your display using four M6 \ screws� Note: Wall mounting solution is not included with the unit and is sold separately� Contact your NEC representative for details�
English-11English-10 English Attaching the Base E322 / E422 / E462E552 1� Place the display face down on a soft and flat surface to prevent scratching and damage� 2� Carefully align the base to the stand and fasten the screws with a cross\ -head screwdriver� CAUTION: The base of the stand is very heavy � Install with care to avoid injury such as dropping the base onto one's foot� Place The Display On A Solid Surface Ensure that the LCD display is placed in a position to allow free flow of air � Do not cover the ventilation openings on the back cover � Do not place the display near any open flames. Do not allow the display to be placed in an environment where it can be exposed to heat, direct sunlight, or rain and water� Do not expose the equipment to any liquid� Antenna Connection Unless your LCD display is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best television performance� However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. When using a 75-Ohm coaxial cable system, connect the CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal� Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal� Min 1 m
English-13English-12 Battery Installation and Replacement The remote control is powered by two 1�5V AAA batteries� To install or replace batteries: 1� Open the battery cover of the remote control by pushing and pulling it in the direction of the arrow� 2� Insert two new “AAA” size batteries for the remote control� When replacing old batteries, push them towards the springs and lift them out� 3� Match the batteries to the (+) and (-) marks in the battery compartment� 4� Insert the bottom of the battery, the (-) side, into the battery compartment first, push towards the springs and insert the top of the battery, the (+) side, into place� Do not force the battery into the battery compartment� 5� Close the battery cover making sure the tabs rest in the corresponding holes and push down the cover until it clicks shut� CAUTION: Incorrect usage of batteries can result in leaks or bursting� NEC recommends the following battery use: • Do not mix battery brands� • Do not combine new and old batteries� This can shorten the battery life or cause liquid leakage of the batteries� • Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment� • Do not touch exposed battery acid as it may injure skin� • Remove the batteries if you do not intend to use the remote control for \ a long period of time�
English-13English-12 English Connect To The Power Source The display should be installed close to an easily accessible power outl\ et� Fully insert the prongs into the power outlet socket� A loose connection may cause image degradation� If there is power to the display, the front LED at the bottom of the display will be either blue or red� A blue LED means the display is powered on� A red LED means the display is in standby mode� Power On/Off Your New LCD Display Press the power key on the remote control or press the power button loca\ ted on the side of the display� The display will power on� DPNQ Power Key or
English-15English-14 Source Connection Guide ® AC POWER E322/E422/E462 E322/E462E422 5 614 2 9 7 3 8 1
English-15English-14 English E552 AC POWER 6 7 5 4 8 921 1� HDMI – Connect the primary source for digital video such as a DVD multimedia player or set top box through this all digital connector� 2� RGB/AUDIO – Connect the video and audio cables from a computer here� 3� AV – Connect the primary source for composite video devices, such as a VCR or video game� Use the white and red connectors to connect the external audio from the same source� 4� COMPONENT (Y-PbPr with Audio L/R) – Connect the primary source for component video devices such as a DVD Player or set top box here� Use red for Pr, blue for Pb, green for Y, red for right audio (R) and white for left audio (L) inputs� 5� AIR/CABLE – Connect to an antenna or digital cable (out of-the-wall, not from Cable Box) for the digital tuner� 6� DIGITAL OUT – When a digital audio signal is associated with the input selected for viewing, the digital audio will be available on this DIGITAL OUT connection to your home theater system� 7� Earphone Output – Connect to the headphones� When the headphone is inserted to the plug, all the speakers will be muted�
English-17English-16 8� USB/SERVICE – Insert USB storage device to view photos and listen to the music� /This USB slot is for future software upgrades� 9� RS-232C – Input from external equipment such as a PC or AV control system in order to control RS-232C functions� Once your AV device is connected, press the Source button on the remote control to select the relevant source to view� (ex: Press COMP button to select “Component” if you have connected a source to the Component input�) RS-232C Port Specifications PC control of the TV Attach an RS-232C cable cross-type (commercially available) to the sup\ plied Din/D-Sub RS-232C for the connections� Note: This operation system should be used by a person who is accustomed to using computers� Communication conditions Set the RS-232C communication settings on the PC to match the TV's communication conditions� The TV's communication settings are as follows: Baud rate:9,600 bps Data length:8 bits Parity bit:None Stop bit:1 bit Flow control:None Communication procedure Send the control commands from the PC via the RS- 232C connector � The TV operates according to the received command and sends a response message to the PC� Do not send multiple commands at the same time� Wait until the PC receives the response before sending the next command� Power Mode Status ModeLED StatusVGAAVComponentHDMI 1-3TV OnBluevvvvv Power SavingPurplev---- StandbyRedvvvvv Power saving support automatically power on when signal appear� Standby to power on by touch up remote or keypad power button�
English-17English-16 English Operating Instructions 1 23 56 4 7 5 6 1 34 2 7 E322/E422/E462 E552 Using The Side Panel Controls 1�VOL +Press to increase the volume� Press this key to shift Right in the OSD menu� 2�VOL -Press to decrease the volume� Press this key to shift Left in the OSD menu� 3�CH ▲/ Press to increase the channel number � Press this key to shift up in the OSD menu� 4�CH ▼/ Press to decrease the channel number � Press this key to shift down in the OSD menu� 5�MENUPress to open or exit the OSD (On-Screen Display) menu� 6�INPUTPress to select the input source� 7�POWERPress to turn on / off (standby) the display �
English-19English-18 Using The Remote Control Power Press to turn On/Off (standby) the power� (Note: To completely turn off the power, unplug the AC cord from the power outlet�) TV Press to choose ATSC/NTSC tuner source mode� AV Press to choose Composite source mode� COMP Press to choose Component source mode� HDMI/PC Press repeatedly to choose PC IN or HDMI source mode� 0 ─ 9 / - number Press to enter the tuner channel number to select channel (Press ‘-’ to choose the sub-channel)� PRE CH Press to display the previous channel� Source Press repeatedly to choose the various input sources� Mute Switch the sound On/Off� VOL+ / VOL- Press + or - to adjust the volume� CH+ / CH- Press + or - to browse through the channels� Exit Press to exit the OSD menu� Display Press to show the information about the input source and tuner channel� PRE CH Ch-List CO M P FAV Press to display the Favorite List� Menu Press to open the OSD menu� ▲, ▼, ◄, ►, OK Press to select or confirm the various function items on the menu�