NEC Code Master An Open Application Interface Installation Guide

NDA-30013   Revision 6.0Page 11
Code Master Installation Guide Application Configuration
Step 4 – Secondary OAI Configuration Parameters
Using the OAI-Conf command on the APM Configuration Entry screen, make the 
entry shown for each of the following parameters required by Code Master. Use the 
instructions provided for this option in the APM Operations Manual:
Parameter
EntryDescription
Database Name #1 /oai/db/cur/cmdb The path name of the tenant mask 
database. The database filename 
cmdb, shown here...

Page 12NDA-30013   Revision 6.0
Application Configuration Code Master Installation Guide
Step 5 – User-defined Parameters
Make the following additional parameter entries through the User Defined 
command on the APM Configuration Entry screen.
Parameter
EntryDescription
User Defined #1 0 Specifies the method of recording 
authorization codes dialed, using 
the following values: 
0 = no codes recorded
1 = invalid codes only
2 = valid codes only
3 = all codes recorded
User Defined #2 /oai/app/auth.record...

NDA-30013   Revision 6.0Page 13
Code Master Installation Guide Database Requirements
Chapter 3 Database Requirements
Code Master requires the following two databases, both of which are created 
through the APM:
Tenant/Mask Database
This database contains all of the tenants served by Code Master and for each, 
the mask that defines the contents of the required authorization code. This 
database is configured as /oai/db/cur/cmdb.
Authorization Code Database
This database contains all of the authorization...

Page 14NDA-30013   Revision 6.0
Database Requirements Code Master Installation Guide
Instructions
The information required for each Code Master database is provided in table form 
in Tenant/Mask Database Information on page 14 and Authorization Code 
Database Information on page 15. Using this information alongside of the 
procedural instructions provided in the APM Operations Manual, enter the 
Database Administration option on the APM System Administration Menu, and 
build the Code Master databases one...

NDA-30013   Revision 6.0Page 15
Code Master Installation Guide Database Requirements
Mask – The ten-character notation that indicates how the authorization code 
must be entered by telephone users assigned to this tenant, using the following 
format:
Digit – The exact digit (0-9) that must be entered by the user for Code Master 
to validate the authorization code.
v – Indicates that this position should be read as a digit of the authorization 
code of up to ten characters that must be validated...

Page 16NDA-30013   Revision 6.0
Database Requirements Code Master Installation Guide
Field Definitions:
Authorization Code – An actual authorization code; valid characters are digits 
0 – 9, #, and *. Records are sorted in ascending order. An entry may be less than 
ten digits long, and should be equal in length to the verifiable portion specified 
in the mask.
Tenant Number Field – A sequence of one or more tenants entered in the 
Tenant/Mask database to which this authorization code is assigned;...

NDA-30013   Revision 6.0Page 17
Code Master Installation Guide NEAX Command Assignments
Chapter 4 NEAX Command Assignments
This guide assumes that data settings that affect the operation of all OAI software 
on a system-wide basis have already been assigned on the NEAX2400 
Maintenance Administration Terminal (MAT) commands, the NEAX2000 
Customer Administration Terminal (CAT), or the NEAX2000 Maintenance 
Operations Console (MOC).   Such settings include, for instance, system index 
values and...

Page 18NDA-30013   Revision 6.0
NEAX Command Assignments Code Master Installation Guide
ASPA: 
(Assignment of 
Special Access 
Code)This command is used to designate the kind of service or the route to be used when 
a trunk access or special access code has been entered. Services include, for 
instance, speed calling, attendant manual override, individual trunk access, 
authorization code/forced account code, call park remote retrieval, least cost 
routing, etc.
(a) Enter the same tenant number that was...

NDA-30013   Revision 6.0Page 19
Code Master Installation Guide NEAX Command Assignments
NEAX2000 Commands
Use the NEAX2000 Customer Administration Terminal (CAT), or the NEAX2000 
Maintenance Operations Console (MOC) to enter these commands. (Refer to the 
NEAX2000 System Manuals for more information.)
CM20: 
(Assignment of 
Access Code)Y=Tenant Group:  Access Code for ID code class change.
1st dataAccess Code (1-3 digits)
2nd dataService Type
:086:Authorization code
Use A57 for the first digit of the...

Page 20NDA-30013   Revision 6.0
NEAX Command Assignments Code Master Installation Guide
CM08:  (Checking 
ID Codes Using 
AP01)Basic Functions
1st data:217Check ID code
2nd data::0:Check through MP
:1:Check through AP01 package when using ACF. (Set checking through AP01 
package when using ACF.)
CMD53:  (Handling 
of ID Codes When 
the IP is Down)Registers ID codes and temporary class data.
1st data:ID code
2nd data :a b b c c d d e e:Temporary class data
:a: 0–2,9:Temporary class type
:b b:...