Namco Victory Lap Ace Driver Operators Manual

							Page 21
7-3-5 Motor Test
Note:Performing the steering motor test can be dangerous, sit on the
seat properly,
  and take hands off the steering wheel.
The following screen is displayed when MOTOR is selected on the I/O screen.
I/O TEST 
DIP 2 12345678 3 12345678
LINK ON 2 COUNT O
SWITCH 
MOTOR BASE MOTOR OFF ............... (a) Seat motor test
STEERING OFF TORQUE  00 ............... (b) Steering motor test
EXIT
GAS: TURN SHIFT: CHOOSE
(a) Unused 
(b) Tests the steering feedback motor. When STEERING is selected and the accelerator is pressed the test is \
ON 
and the motor will start and turn the steering wheel left and right.
Pressing the accelerator again turns the test OFF and the motor will s\
top.
Select EXIT to return to the I/O test screen. 
7-3-6 Lamp Test The following screen is displayed when LAMP is selected on the I/O scr\
een.
Select EXIT to return to the I/O test screen.
I/O TEST 
DIP 2 12345678 3 12345678
LINK ON 2 COUNT 0
LAMP TOP LAMP ........................ (a) Tests top lamp. 
SIGNAL LAMP RED ........................ (b) Unused
SIGNAL LAMP GREEN ........................ (c) Unused
EXIT
GAS: LIGHT SHIFT: CHOOSE 
						

							Page 22
7-3-7 Sound Test
To adjust the sound volume, select SOUND TEST in the menu screen. The
following screen will be displayed.
SOUND TEST [DEFAULT IN GREEN]
VOLUME [MAX 63]
LEFT RIGHT
(a) Left speaker volume ...................... 40 40 .................. (b) Right speaker volume
SONG 00
EXIT
GAS: ENTER SHIFT: CHOOSE
Select (a) or (b) by using the shift lever, the characters will blink in red, when the
accelerator is pressed the numbers will start to blink. Moving the shift lever up will
increase the number, moving the shift lever down will decrease the number.
The volume can be adjusted in 64 steps, with 00 the quietest and 63 the loudest. The
factory setting is 40
Select EXIT to return to the menu screen
7-3-8 Monitor Test
a) Select item (5) Monitor Test on the menu screen to set up and adjust the
monitor.
b) On entering monitor test, the screen will display one of the following test patterns.
GRADATION PATTERN
CROSSHATCH GREEN
CROSSHATCHWHITE
WHITE WINDOW (H)
WHITE WINDOW (M)
WHITE WINDOW (L)
INTERLACE PATTERN
VIEW ANGLE ADJUST (CRT)
VIEW ANGLE ADJUST (PROJ)
FULL WHITE
c. Use the shifter to change to the next pattern and accelerator to return to Main
Menu. 
						

							Page 23
7-4 Adjustments When Replacing Parts (Initialization)
The following adjustments should always be performed after replacing the\
 game PC 
board, ROM, Steering Assy, Pedal Assy, or Control Pots.
The game will not operate correctly if these adjustments are not made. 
a) Ensure that accelerator and brake pedals are fully returned. 
b) Place the steering wheel to its centre position and remove hands from t\
he wheel (
The steering wheel does not return to centre by itself.)
c) Slide the test switch ON while pressing the service switch. The follow\
ing screenwill be displayed on the monitor.
d) Press the service switch to reset all values to 0000 
e) Fully depress and release the accelerator, then the brake, then turn the steering wheel fully left and right.
f) Slide the test switch OFF to return to normal game mode.
Note: If the above initialization does not perform correctly , repeat two or three times.
ADJUST MODE
BASE BIAS VALUE
STEER: **** **** 0000
GAS: **** **** 0000
BRAKE: **** **** 0000
ADJUST WHILE PRESSING SERVICE SWITCH.
TO EXIT, TURN OFF TEST SWITCH. 
						

							Page 24
8. MAINTENANCE
8-1 Replacing the Fluorescent Lamp
1) Remove four Security Button Head Screws (M4x25) and washers from the top of
the header acrylic.
2) Remove four Security Button Head Screws (M4x25) from the Acrylic/Glass
retaining bracket, and remove the bracket.
3) Remove the Header Acrylic.
4) Replace the Fluorescent Tube. 
						

							Page 25
8-2. AB Pedal Assembly
8-2-1. Removing the AB Pedal Assembly 1) Remove the four security screws (M6x25), and withdraw the assemblyforward.
2) Disconnect the connector, and remove the assembly.
8-2-2 Replacing the Control Pots. 1) Loosen the quadrant gear clamp screw, and remove the quadrant gear. 
2) Loosen the gear grub screw, and remove the gear.
3) Replace the control pot.
Note: When replacing the control pot
a. Ensure that the potentiometer locating tag is engaged in the mounting pl\
ate
hole.
b. Turn the potentiometer shaft almost fully clockwise before engaging the
quadrant gear .
After replacing the Control the game 
must be re-initialized  (See section 7-4
Adjustments when Replacing Parts 
						

							Page 26 8-3. Shift Assembly Maintenance
1) Removing the Shift assembly
a). Remove the four security screws (M6x16), and withdraw the shift
assembly.
b). Disconnect the connector.
2) Replacing the Microswitch
a) Remove the two pozi head screws (M3x16), and replace the switch.
b) Ensure that the switch is refitted the correct way round and the wires are fitted
to correct terminals.
8-4 Steering assembly Maintenance
1) Remove four Security Screws (M6x25) and hinge the play panel forward and
down. 
						

							Page 27
8-4-1 Replacing the Control Pot
1) Disconnect the Control Pot connector. 
2) Loosen the grub screw . 
Take care not to remove the screw completely .
3) Loosen the pozi head screw retaining the Control Pot bracket and remove
the bracket with the  Control Pot .
4) Replace the Control Pot.
Note : Before re-tightening the grub screw
ensure that it engages on the flat of the pot shaft.
After replacing the Control the game 
must be
re-initialize d (See section 7-4 Adjustment
when Replacing Parts).
8-4-2 Replacing the Drive Belt or Steering Motor
1) Disconnect the motor connector. 
2) Loosen the four nuts (M5) retaining the motor mounting bracket to the \
frontplate.
3) Loosen the tension adjuster bolt (M6x60) and slide the motor mounting bracket towards the main gear to release the drive belt.
4) Remove the drive belt.
5) Remove the four nuts (M5) and remove the motor and motor mounting plate.
Note:- When replacing the drive belt, the centre part of the belt should be able to bend approx. 2 to 3mmwhen a force of 500g is applied 
						

							Page 28
9. PARTS 
						

							Page 29
ITEMDESCRIPTIONPART No
1EVA Floor Mat45000184
228 Polo Monitor84000026
3Front Glass31000024
4Side Decal - RHS45000337
5M16 Adjustable Foot88300079
6Castor - 75mm59000005
7Side Decal - LHS45000336
8Victory Lap PCB AssemblyXVL - PCB
9Schaffner Mains Input Assembly66000016
10Link PCB AssemblyXAD-LINKPCB
11Steering PCB Transformer67700020
12Lamp Drive PCB45000670
13SMPSU - 5V @ 32A / 12V @ 12A83000001
14
Fuse 1¼ 1A Slo-Blo63500639
Fuse 1¼ 1A Q.B.63500424
Fuse 1¼ 5A Slo-Blo63500643
15Steering Motor PCBXAD-STEERPCB
16Fan 240V - 4½67000015
17Interlock Switch60000006 
						

							Page 30
ITEMDESCRIPTIONPART No
1FLUORESCENT TUBE - 4ft64500014
2HEADER ACRYLIC24201027
3E14 240v 25w GOLFBALL LAMP64000084