Namco Prop Cycle Operators Manual

							Page 11 4-3 Removing the Shipping Bracket
1. Remove the two Hex Head Set Screws (M8x16) retaining the shipping
bracket to the Cycle Base.
2. Remove the two Hex Head Set Screws (M12x20) retaining the shipping
bracket to the Cycle Assembly.
3. Remove the shipping bracket. (Ensure that the bracket and the M8 screws
and washers are retained safely for refitting if the machine is moved or
transported in the future.)
4. Refit the two Hex Head Screws (M12x20) with washers to the Cycle
Assembly and tighten fully. 
						

							Page 12
5. ADJUSTMENTS
5-1 Turning on the PowerAfter the machine has been installed, turn ON the power. The Power switch is 
located on the rear of the Main cabinet. (See section 3 “Major Compo\
nents”
(page 3).)
5-2 Adjustment Switches The adjustment switches are located inside the coin door. 
1. Service Switch Press this switch to obtain game credits without incrementing the play m\
eters.
2. Test Switch Slide this switch “ON” to enter test mode. 
Test mode allows game testing and the changing of game settings. (Refer \
to
section 5-3 “ Test Mode” (page  13).)
LEFT 
PLAYER RIGHT PLAYER
TEST SERVICE
TEST SERVICE
COIN COUNTER 
						

							Page 13
5-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Sc\
reen” will be displayed on the monitor.
2. Select the test required by moving the handle bars up or down. The colou\
r of the selected test will change.
3. Enter the selected test by pressing the start button. Select “EXIT”\
 to return to the “Menu Screen”
4. After testing is completed, ensure that the test switch is returned to t\
he “OFF” position to return to game mode.
The T est Switch must always be in the “OFF” position for normal game mo\
de.
MENU
COIN OPTIONS -------------------------- (1) Sets the price of play. 
(See 5-3-1)
GAME OPTIONS -------------------------- (2) Sets the game options.
(See 5-3-2)
I/O TEST -------------------------- (3) Used for testing the switches and
fan. (See 5-3-3)
MONITOR TEST -------------------------- (4) Used for adjusting the monitor.
(See 5-3-4)
SOUND TEST -------------------------- (5) Used for adjusting the speaker
volume. (See 5-3- 5)
ADS DATA -------------------------- (6) Displays the accumulated game
data.
OTHERS -------------------------- (7) Used for testing the PC boards and
for initializing all of the settings.
START : ENTER UP/DOWN : CHOOSE 
						

							Page 14 5-3-1 Coin Options
a. Select item (1) “COIN OPTIONS” on the menu screen, to set the
game cost and related settings.
b. Move the handle bars up or down to select the required item then
press the start button.
c. Move the handle bars left or right to change the settings then press
the start button to store the new values.
d. Select “EXIT” and press the start button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure
that the Coin Options on the screen are set as shown in the following table.
COIN OPTIONS [DEFAULT IN GREEN]
GAME COST
1 COIN 1 CREDIT............................. (a)
CONTINUE COST
1 COIN............................. (b)
FREE PLAY
OFF ............................. ( c )
EXIT
START: ENTER
ITEMCONTENTSFACTORY SET
(a) Game CostCoins required for one credit - - - - - settable 1 - 91
(b) Continue CostCoins required to continue play - - - settable 1 - 91
(c) Free PlayNo coins required for game - - - - - - On / OffOFF 
						

							Page 15 5-3-2 Game  Options
a. Select item (2) “GAME OPTIONS” on the menu screen to set the
game options.
b. Move the handle bars up or down to select the required item then
press the start button.
c. Move the handle bars left or right to change the settings then press
the start button to store the new values.
d. Select “EXIT” and press the start button to return to the menu
screen.
GAME OPTIONS [DEFAULT IN GREEN]
DIFFICULTY B............................. (a)
CONTINUE TIME B............................. (b)
HI-SCORE INIT NO............................. ( c )
SOUND IN ATTRACT ON............................. (d)
EXIT
START : ENTER
ITEMCONTENTSFACTORY SET
(a) DifficultyA (easy) to C (hard)B
(b) Continue TimeTime allowed to continue new game. A (long) to C (short)B
(c) Hi-Score InitYes / No  (If Yes, Hi-Score will be reset when exiting test)NO
(d) Attract SoundSound during standby attract mode    Yes / NoYES 
						

							Page 16
5-3-3 I/O Test
a. Select item (3) “I/O TEST” on the menu screen. 
b. Move the handle bars up or down to select the required item thenpress the start button.
c. Move the handle bars left or right to change the settings then press the start button to store the new values.
d. Select “EXIT” and press the start button to return to the menu scr\
een
I/O TEST
DIP 12345678 .................................... (a)
SWITCH .................................... (b)
PEDAL .................................... ( c )
MOTOR .................................... (d) 
LAMP .................................... (e)
EXIT 
START : ENTER UP/DOWN : CHOOSE
(a) Displays the state of the PCB Dip switches, when a switch is ON thenumber is shown in red.
(b ) Tests the switches and handle bars .(See 5-3-3-1.)
(c ) Tests the pedals    (See 5-3-3-2.)
(d ) Tests the fan moto r. (See 5-3-3-3.)
(e ) Tests the start button lamp .(See 5-3-3-4.) 
						

							Page 17 5-3-3-1 Switch Test
a. Select “SWITCH” on the menu screen and press the start button. The
following screen is displayed.
I/O TEST
DIP 12345678
SWITCH
UP / DOWN : 0000................................... (a)
RIGHT / LEFT : 0000................................... (b)
S TA RT : OFF ................................... ( c )
COIN : OFF................................... (d)
SERVICE : OFF................................... (e)
TO EXIT : PUSH START AND HANDLEBARS UP
(a) Handle Bar up/down: When the handle bar is pulled back the value
of 0000 will increase and ‘OK’ will appear when
the handle bar is fully back.
(b) Handle Bar left/right: When the handle bar is pushed forward the
value of 0000 will decrease and ‘OK’ will
appear when the handle bar is fully forward.
Note: It is normal for 0000 to be changing
slightly when the handle bar is in the
neutral position.
(c) Start button ‘OFF’ will change to ‘ON’ each time the start
button is pressed.
(d) Coin switch ‘OFF’ will change to ‘ON’ when the coins to the
correct game value have been inserted through
the Cashflow acceptor.
(e) Service ‘OFF’ will change to ‘ON each time the service
button is pressed.
NOTE: If ‘OK’ does not appear when the handle bars are at there
extreme travel, re-initialize the game as described in section 4 
						

							Page 18 5-3-3-2 Pedal Test
a. Select “PEDAL” on the menu screen and press the start button. The
following screen is displayed.
I/O TEST
DIP 12345678
SWITCH
PEDAL
PEDAL 7FBF.................... (a)
READY
PRESS START.................... (b)
TO EXIT : PUSH START AND HANDLEBARS UP
}
(a) Pedal rotation When the pedals are rotated in the forward
direction the value increases, and when they
are rotated in the backward direction the value
decreases.
(b) Rotation sensor check This mode checks whether the sensor is
reading the pedal rotation correctly. (see
below)
b. When the start button is pressed,  the following screen is displayed.
I/O TEST
DIP 12345678
SWITCH
PEDAL
PEDAL ACB7
NOW COUNTING
PEDAL IT 10 TIMES
THEN PRESS START
TO EXIT : PUSH START AND HANDLEBARS UP
c. When the above screen is displayed, pedal ten full turns in the
forward direction. Stop as soon as the pedal has been turned
exactly ten times.
d. Press the start button again. 
						

							Page 19 e. When the start button has been pressed, the following screen is
displayed.
f. If “OK” is displayed the pedals are correct.
If “NG” is displayed there has been a problem in reading the pedal
rotation. Press start and repeat steps c) and d) again.
If “NG” is still displayed after repeating the test, there is the
possibility that the sensor board or sensor sticker is faulty.
g. Press the start button while pulling back on the handle bars, to return
to the “I/O Test” menu.
5-3-3-3 Fan Motor Test
a. Select “MOTOR” on the menu screen and press the start button. The
following screen is displayed.
b. When the start button is pressed once, ‘OFF’ changes to ‘ON’ and
the fan motor starts and blows air from the front of the cabinet. When
the start button is pressed again, ‘ON’ changes to ‘OFF’ and the fan
motor stops.
c. Select “EXIT” and press the start button to return to the “I/O Test”
screen.I/O TEST
DIP 12345678
SWITCH
PEDAL
PEDAL C5CF
END
OK
RETRY : PRESS START
TO EXIT : PUSH START AND HANDLEBARS UP
I/O TEST
DIP 12345678
SWITCH
PEDAL
MOTOR
FAN MOTOR OFF
EXIT
START : ENTER UP/DOWN : CHOOSE 
						

							Page 20 5-3-3-4 Lamp Test
a. Select “LAMP” on the menu screen and press the start button. The
following screen is displayed.
b. When the start button is pressed once, ‘OFF’ changes to ‘ON’ and
the start button lamp turns ON. When the start button is pressed
again, ‘ON’ changes to ‘OFF’ and the start button lamp turns OFF.
c. Select “EXIT” and press the start button to return to the “I/O Test”
screen.
5-3-4 Monitor Test
a. Select “MONITOR TEST” on the menu screen and press the start
button. The following screen is displayed.
b. Select an item with the handle bars and then press the start button.
Press the start button to exit a selected pattern.I/O TEST
DIP 12345678
SWITCH
PEDAL
MOTOR
LAMP
BUTTON OFF
EXIT
START : ENTER UP/DOWN : CHOOSE
    MONITOR TEST
GRADATION PATTERN
CROSSHATCH PATTERN [CRT]
CROSSHATCH PATTERN [PROJECTOR]
WHITE WINDOW [H]
WHITE WINDOW [M]
WHITE WINDOW [L]
INTERLACE PATTERN
VIEW ANGLE ADJUST [CRT]
VIEW ANGLE ADJUST [PROJECTOR]
FULL WHITE
EXIT
START : ENTER UP/DOWN : CHOOSE