Home > Multitech > Communications System > Multitech MultiVOIP200 Upgrade User Guide

Multitech MultiVOIP200 Upgrade User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Multitech MultiVOIP200 Upgrade User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 17 Multitech manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							1
    MultiVOIP200 Upgrade Caution
    Product Update
    10/19/00
    Part Number: 82095116, Rev. B
    Important read before installation: MultiVOIP200s with H.323 compatible firmware (MVP200
    version 2.50 or later) are not compatible with MultiVOIPs using earlier versions of firmware.
    Also, the MultiVOIP200s with H.323 compatible firmware will not operate behind non-H.323 compliant proxy
    servers or firewalls.
    Choosing Proprietary or H.323 mode for your new MultiVOIP200
    The MultiVOIP200s are shipped with the H.323 compatible firmware version 2.50 installed. If you want to
    run in proprietary mode(compatible with versions prior to 2.50), you will need to download firmware
    version 2.01D to your MultiVOIP200. Refer to the users guide for instructions to download version 2.01D.
    Both versions are included on the CD shipped with this product.
    Warning: If the MultiVOIP has firmware version 2.50 installed and you run “MultiVOIP
    configuration” using software version 2.01D, you will receive the message “This version of the software
    does not support the MultiVOIP firmware version 2.50. Some of the configuration parameters will be
    inconsistent and the Download option is disabled. Please contact MultiTech Tech support for the
    latest software release.”. If you receive this message, then you need to download firmware version
    2.01D to your MultiVOIP200.
    Reasons you may want to use proprietary mode include:
    1. If you intend to use your MultiVOIP behind a non-H.323 compliant Proxy server or firewall, you will need
    to use version 2.01D.
    2. If you are installing your new MultiVOIP in an existing Multi-Tech VOIP network and don’t want to
    upgrade all your existing MultiVOIPs to make them H.323 compatible.
    Clearing Call Logs before downloading firmware
    Before downloading firmware you must clear the call logs. To clear the call logs, run “MultiVOIP
    configuration” using your old MultiVOIP software. Select Statistics from the Main Menu and then select
    Logs. Then click on the “clear” button to clear all logs. Note: this will remove all previous logs; you may
    want to print the call logs before you clear them. You can then exit the MultiVOIP software.
    Warning: Call logging will not function properly if this step is skipped. 
    						
    							2
    Upgrading your previously-installed MultiVOIP200s from 2.01D or
    earlier to H.323 (version 2.50).
    MVP200 version 2.50 Installation Instructions
    Note: steps 5 - 9 must be performed locally via the command port.
    Note:  there are two different MVP200 hardware platforms. If you have the hardware platform where the VOICE
    CHANNEL 2 LEDs are above the CHANNEL 1 LEDs, you must confirm that sufficient Flash memory is installed
    before proceeding with the upgrade. To verify this, remove the two screws from the bottom of the chassis and slide
    the entire cover forward. With the LEDs toward you, verify that the four sockets (U12, U13, U14 and U15) along
    the left side of the lowest PCB have a Flash memory chip installed. If sockets U14 and U15 are empty, contact
    Multi-Tech to obtain a Flash Memory upgrade (two Flash memory chips, PN 00929046).
    1. Run MultiVOIP configuration from your old version of MultiVOIP software and take note of the current
    settings. Your MultiVOIP will be reset to factory defaults during this upgrade.
    2. While still running “MultiVOIP configuration”, select Statistics from the Main Menu and then select Logs.
    Then click on the “clear” button to clear all logs. Note: this will remove all previous logs; you may want to print the
    call logs before you clear them. You can then exit the MultiVOIP software.
    Warning: Call logging will not function properly if this step is skipped.
    3. Uninstall your old version of MultiVOIP software by selecting the Uninstall MultiVOIP Configuration option
    from the program group.
    4. Install the H.323 compatible software from the MultiVOIP CD.
    5. From the program group of the MultiVOIP software, run Download H.323 Stack and select the default file.
    6. From the program group of the MultiVOIP software, run Download Voice Coders and select the default file.
    7. From the program group of the MultiVOIP software, run Download Factory Defaults.
    8. From the program group of the MultiVOIP software, run Download Firmware. Under File Name,
    enter *.upg and hit enter. There are two different hardware platforms for the MultiVOIP200.
    If your MultiVOIP200 voice channel 2 LEDs are above the voice channel 1 LEDs, select the file BOOT_200.UPG.
    If your MultiVOIP voice channel 2 LEDs are to the right of the voice channel 1 LEDs, select the file
    BOOT_20A.UPG.
    Warning: If you select the incorrect file your MultiVOIP will need repair.
    9. From the program group of the MultiVOIP software, run Download Firmware and select the file mtvoip.bin.
    10. Run MultiVOIP Configuration and reconfigure your MultiVOIP. The upgrade is complete. 
    						
    All Multitech manuals Comments (0)

    Related Manuals for Multitech MultiVOIP200 Upgrade User Guide