Multi-Tech Systems Multivoip 200 Model Mvp200/800 Standalone Voice/ip Getaway User Guide

							51 Chapter 4 - MultiVOIP Software
Others Setup
Clicking the Others button on the main menu displays the Others Setup dialog box. This dialog box
lets you to enable SNMP Agent (the default is disabled) and set up all the necessary parameters;
enable or disable various remote configuration methods such as TFTP (Trivial File Transfer Protocol)
Server, Web Server, Dumb Terminal, and Telnet Server; and assign a Password to the MultiVOIP for
Internet security. These applications enable remote viewing and changing of the MultiVOIP
configuration, or updating firmware, from anywhere on the connected internetwork.
Verify that the desired applications are enabled (checked). The default condition is all applications are
checked. To disable a given application, click to uncheck the check box and disable support.
SNMP related operations can be performed only when the SNMP Agent is enabled (checked) on this
dialog box. The IP address of the system (i.e., SNMP Manager) that will receive the Traps from the
MultiVOIP should be entered in the IP Address field in the Trap Manager group. The Community
Name of the SNMP Manager receiving the Traps can be a maximum of 19 characters and 
is case
sensitive. The default Port Number of the SNMP Manager receiving the Traps is 162. The MultiVOIP
currently supports a maximum of two community users at a time, and they can be assigned either
Read/Write or Read Only rights.
For more information on using these applications, click the on-line Help button or refer to Chapter 5,
Remote Configuration and Management.   
						

							52 MultiVOIP User Guide
Viewing Call Progress
The Call Progress dialog box displays the status of a call in progress. This dialog box is accessed
from the MultiVOIP Setup menu by clicking on the Call Progress button.
The ratio of Packets Lost versus Packets Received provides a general indication of the integrity of
the Internet connection. To reduce the frequency of lost packets, select a low-bit-rate coder, such as,
G.723 or Netcoder. In addition, enabling Forward Error Correction option in the Channel Setup dialog
box under the Voice/Fax tab will enable the MultiVOIP to recover many of the lost packets.
The Jitter (ms) value indicates the mean deviation of the difference in packet spacing at the receiver
compared to the sender for a pair of packets.   
						

							Chapter 5 - Remote Configuration and Management 
						

							54 MultiVOIP User Guide
Introduction
This chapter provides procedures for viewing or changing the configuration of a remote unit.  Two
methods are provided to access a remote unit; the first method is modem based and the second
method is using IP.  Within the IP method, three applications can be used: 1) LAN-Based using TFTP
(Trivial lFile Transfer Protocol), 2)Telnet as a client application, or 3) a standard web browser on the
Internet.
Remote Configuration
Remote configuration requires the MultiVOIP software to be loaded on the local PC.  The local PC
then controls the remote MultiVOIP either via the modem connection or the LAN.
Modem-Based
To remotely configure a MultiVOIP, a local PC needs to be connected to a dial-up line and the
MultiVOIP software configured to call the remote MultiVOIP. The remote MultiVOIP needs to have a
modem connected to a dial-up line and the Command Port. Once the connection to the remote unit is
made, you can change the configuration as you see fit. Once the configuration is changed, you can
down load the new configuration to the remote MultiVOIP. Refer to the Modem-Based Remote
Configuration Procedure in this chapter to remotely configure a MultiVOIP.
1 At the remote site, remove the serial cable from the PC to the Command Port connector on
the back panel of the MultiVOIP.
2 At the remote site, connect a special cable (Remote Configuration Cable) from the Command
Port connector on the back panel of the MultiVOIP to the RS-232 connector on the modem.
The special cable is a serial cable with male connectors on both ends. Refer to Appendix B
for cable details.
Connect the modem to your local telephone line.
Provide your telephone number to the person verifying your configuration.
Configure the remote modem for 19200 baud and turn on Force DTR.
3 At the main site, connect your local PC to a modem that is connected to a dial-up line.
4 Install the MultiVOIP software on the local PC. When installed, click Start | Programs |
MultiVOIP | Configuration Port Setup, or double click on the Configuration Port icon in
the MultiVOIP program group.
5 The MultiVOIP Setup dialog box is displayed.   
						

							55 Chapter 5 - Remote Configuration and Management
Verify that the Communication Type is set for COM Port and the Select Port field is set for
the COM port of your local PC.
In the Dial String field, enter the AT command for dialing (ATDT) plus the phone number of
the remote MultiVOIP.
If your Modem Initialization String, Initialization Response, or Connect Response values are
different than the defaults in the dialog box, refer to your modem user documentation and
change the default values to match your modem.
Click OK when you are satisfied with your selections.
6 Run the MultiVOIP Configuration program. Click Start | Programs | MultiVOIP | MultiVOIP
Configuration, or double click on the MultiVOIP Configuration icon in the MultiVOIP
program group.
7 The Dialing dialog box is displayed while software is dialing the remote MultiVOIP.
8 The Reading Setup dialog box is displayed.
9 The MultiVOIP Setup menu is displayed. This is the dialog box of the remote MultiVOIP.
Refer to the online Help provided with your software for a description of each dialog box and
field within a dialog box.
10 After you have changed the configuration of the remote MultiVOIP, click Download Setup to
update the configuration. The remote MultiVOIP will be brought down, the new configuration
written to the unit, and the unit will reboot.
11 Click Exit when the downloading is complete.
12 The Hangup connection? dialog box is displayed
Click Yes to disconnect the phone connection to the remote site.
13 If the same telephone number is not going to be used again in the immediate future, you may
want to remove it from the Port Setup dialog box.
14 At the remote site, reconnect the MultiVOIP to the serial port of the PC and from the
MultiVOIP program group double click on the MultiVOIP Configuration icon to verify that the
MultiVOIP is running.   
						

							56 MultiVOIP User Guide
LAN-Based 
The LAN-based remote configuration requires a Windows Sockets compliant TCP/IP stack. TCP/IP
protocol software must be installed and functional before the configuration program can be used.
1 You must assign an Internet (IP) address for the PC and for each node that will be managed
by the configuration program. Refer to the protocol software documentation for instructions
on how to set the IP addresses.
Once you have completed this step, you should be able to use the protocol Ping command
for the PC host name. You should also test the network interface configuration by Pinging
another TCP/IP device that is connected to the network.
2 Install the MultiVOIP software on the local PC. When installed click Start | Programs |
MultiVOIP | Configuration Port Setup, or double-click on the Configuration Port Setup
icon in the MultiVOIP program group.
3 The MultiVOIP Port Setup dialog box is displayed.
Verify that the Communication Type field is set IP.
In the MultiVOIP IP Address field, enter the IP Address of the remote MultiVOIP.
4 Click OK when you are satisfied with your selections.
5 Run the MultiVOIP Configuration program. Click Start | Programs | MultiVOIP | MultiVOIP
Configuration, or double click on the MultiVOIP Configuration icon in the MultiVOIP
program group.
The Reading Setup dialog box is displayed.
6 The MultiVOIP Setup dialog box is displayed. This is the dialog box of the remote MultiVOIP.
Refer to the online Help provided with your MultiVOIP for the definition of each dialog box     
						

							57 Chapter 5 - Remote Configuration and Management
and field within a dialog box.
7 After you have changed the configuration of the remote MultiVOIP, click Download Setup to
update the configuration. The remote MultiVOIP will be brought down, the new configuration
written to the unit, and the unit will reboot.
8 Click Exit when the downloading is complete.
9 Double click on the MultiVOIP Configuration icon in the MultiVOIP program group to verify
that the MultiVOIP is running.   
						

							58 MultiVOIP User Guide
Remote Management
This section describes typical client applications that can be used to configure the MultiVOIP
remotely. It is important to note that although any subsequent changes to configuration can be made
using these applications, the initial setup and configuration of the MultiVOIP must be done on the
local PC, using the MultiVOIP software provided with your unit.
Although establishing access to the MultiVOIP varies between applications, the configuration
functions mirror those of the MultiVOIP software. For more information on MultiVOIP software, refer
to Chapter 4 - MultiVOIP Software.
Telnet
A typical Telnet client application is described next. The MultiVOIP has a built-in Telnet Server that
enables Telnet client PCs to access the MultiVOIP. A typical Telnet client is allowed to configure the
MultiVOIP.  In addition, the MultiVOIP can be remotely accessed and configured from any where on
the Internet through its Web interface.  A typical TCP/IP program group is shown below with a
Tcpman icon and a Telnet icon.
The TCP/IP stack has to be loaded before the Telnet client (a Windows application) will run. The
Telnet Server option has to be selected from the Applications Setup dialog box using the MultiVOIP
Configuration icon. Double click on the Telnet icon (or shortcut) and a blank Telnet screen is
displayed. Click Connect | Remote System and the Connect dialog box is displayed. Select (or
enter) a Host Name (the IP address of the MultiVOIP).In this example, the Host Name is
192.168.2.8.
When you enter a valid Host Name (IP address) and click on the Connect button, you are
immediately connected to the target MultiVOIP and the MultiVOIP Telnet Server screen is displayed. 
						

							59 Chapter 5 - Remote Configuration and Management
MultiVOIP Telnet Server Menu
The MultiVOIP Telnet Server menu provides three basic options: Voice over IP Configuration, Phone
Directory Database, and Phone Directory Configuration. A further option enables you to close the
Telnet session.
Voice over IP Configuration
Selecting Option 1 displays the main menu, which allows further configuration options. These
options include Protocol Stacks (option 1), Applications (option 2), System Information (option 3), and
Voice Channels (option 4). For further descriptions of these options, refer to Chapter 4 - MultiVOIP
Software.
Phone Directory Database
Selecting Option 2 allows you to add entries to the Phone Directory Database. Refer to Chapter 4 -
MultiVOIP Software, for more details on the database.
Phone Directory Configuration
Selecting Option 3 allows you to configure and manage the Phone Directory. The various options
are described in detail in Chapter 4 - MultiVOIP Software.     
						

							60 MultiVOIP User Guide
WEB Management
The MultiVOIP can be accessed, via a standard Web browser, from anywhere on the connected
Internet. In order to provide this support, the WEB Server option has to be enabled from the Others
button in the main menu which displays the Applications Setup dialog box (see Chapter 4 - MultiVOIP
Software).
Once enabled, users can access the MultiVOIP by entering its IP address in the destination field of
their web browser. The following screen appears.
If a Password was entered in the Applications Setup dialog box, then enter the password and click on
the Enter button.
From this screen you can access all the configuration options. Refer to Chapter 4 - MultiVOIP
Software, for a description of the various options.