MSI Ms6728 Ver 1 Manual

MS-6728 ATX Mainboard
C-18
Once the installation is complete, go to Start ---> Programs --->VIA --
->raid_tool.exe to enable VIA RAID Tool.
After the software is finished installation, it
will automatically started every time Windows is
initiated. You may double-click on the          icon shown
in the system tray of the tool bar to launch the VIA
RAID Tool utility.
Using VIA RAID Tool 

VIA VT6420 Serial ATA RAID Introduction
C-19
The main interface is divided into two windows and the toolbar above
contain the main functions. Click on these toolbar buttons to execute their
specific functions.  The left windowpane displays the controller and disk drives
and the right windowpane displays the details of the controller or disk drives.
In this model, the available features are as following:
Click on o rbutton to determine the viewing type of left win-
dow pane. There are two viewing types:...

MS-6728 ATX Mainboard
C-20
Click on the plus (+) symbol next to Array 0---RAID 0 to see the details of
each disk.
You may also use the sameo r button to view the statuses of
Array 0---RAID 1. 

VIA VT6420 Serial ATA RAID Introduction
C-21
Click on the plus (+) symbol next to Array 0---RAID 1 to see the details of
each disk. 

The explanation for overspecification and overclocking
D-1
The default specification of Intel® 865PE chipset is only able to support
FSB 400/533MHz  CPU and DDR 266/333/400 DRAM technology. However,
we have spent engineering efforts to allow the overspecification and
overclocking of 865PE Neo2-P under certain conditions. Here is the informa-
tion which could help you to achieve overclocking more easily.
Should you decide to overspec the mainboard, the following conditions
shall be satisfied in order to...

D-2
 MS-6728 ATX Mainboard
2. Configure BIOS settings
You also need to configure BIOS settings for overclocking.
A. In the “Frequency/Voltage Control”, configure “Dynamic OverClocking”
and “Performance Mode” to the settings you wish to overclock.
B. In the “Frequency/Voltage Control”, configure “DRAM Frequency” to
the setting you wish to overclock.
C If the frequency after overclocking is not stable, you may fine-tune the
settings of  ‘CPU Voltage” and “DDR Power Voltage” by adjusting to a
higher value....

The explanation for overspecification and overclocking
D-3
3. System configuration and DDR 400/PC 3200 Qualified Memory Test List
When using DDR400 memory modules, a maximum of 2 DIMMs are
recommended. Please refer to the system configuration and DDR400/PC3200
DIMMs listed below for overclocking.
Table 1: System Configuration
  System Configuration  Manufacturer Model No.  Spec.  Processor Intel P4 2.6GHz  800MHz  Memory As Follows      VGA Card MSI MS-8894 v120  G4Ti4200 8X  Lan Card Onboard     Sound...

D-4
 MS-6728 ATX Mainboard
Table 2: DDR433/466/500 Memory Test List
          Model  Mem. Size DDR Memory Slot Memory Bandwidth R.S.T     1 3 Benchm ark  TwinM O S M 2GII08AKATTIF083S9TD  256M B  433      √ √ OK OK K ingston K H X 3500/256  256M B 433      √ √ OK OK O CZ O CZ433256EL   256M B 433      √ √ OK OK G eIL G D 3500-512D C  256M B 433      √ √ OK OK K ingston K H X 3500/512  512M B 433      √ √ OK OK AD ATA M D0ADH F3G31JB1FC2  256M B 450 
√ √ OK OK TwinM O S M 2GGI08AFATTGF0811DDT  256M B  466...