MSI 7300 Dynalink 2 Manual

Appendix     47
Display toggles between 
“Error” and “buttn” A key is stuck or is being 
he
ld down Check switches for damage
Ensure that a remote is not 
co

ntinuously transmitting 
Optional RF Remote 
display does not 
 workUnits not mated
See “Setting the Transmitter 
and Rece
iver Address” 
procedures.
Lo Batt is blinking Battery is low Replace (alkaline) or recharge 
batter

ies
Unit turns on, then 
i
 mmediately off Battery is low
Replace (alkaline) or recharge 
batter
ies
Tension will not zero...

48    MSI-7300 Operator’s Manual
7.2 Error Codes
The ScaleCore processor that is the heart of the  MSI-7300  Dyna-Link2 detects errors and 
generates error codes to aid in troubleshooting. 
Table 7-2. Error Codes
Error CodeDefinitionComment
LcOFF LC Disabled A load cell was not enabled
2CAL In Cal The system is in calibration mode. 
Do n

ot send commands unrelated to 
calibration.
unCAL Not Calibrated System has not been calibrated.
Error
LoadOverload
Tension/Weight exceeds set 
capacity +9d
Load 
Cell...

Appendix     49
7. 3
5000 lbs / 2500 KGMAXIMUM CAPACITY
7300
lb
B
C = DIA.
E = LOAD CELL 
BODY WIDTH AT 
SHACKLE 
INTERFACE.A
D G
F
Mechanical Dimensions
Figure 7-1. Mechanical Dimensions
Table 7-3. Mechanical Dimensions
CapacityABCDEFGApprox 
Shipping 
WtShackle
1000 lb8.0 in13.53 in.75 in5 in.99 in1.69 in1.75 in4.4 lbG-2130 3.25T
500 kg203 mm344 mm19 mm127 mm25 mm43 mm44.4 mm2.0 kg
2500 lb 8.5 in14.03 in.75 in5 in .99 in1.69 in 1.75 in 4.9 lb
G-2130 3.25T
1250 kg 216 mm356 mm19 mm127 mm 25 mm43 mm 44.4...

50    MSI-7300 Operator’s Manual
7.4 Firmware Update Procedure
Updating firmware in the  MSI-7300  requires the following:  a DCE serial cable (MSI 
503363-001, or build per DCE cable schematic on page 22), a PC with a terminal program 
(“Teraterm Pro” recommended),  and if the PC does not have standard RS-232 serial ports, 
then a USB to serial converter. Make sure  the driver for the USB converter is properly 
installed, and that the terminal program is set up for the proper comm port.
The latest...

Appendix     51
8. After the file is received, terminal should  display “Completed.” Then the boot menu 
appears again.
MSI8000 SCALECORE2 BOOT LOADER Ver. 02-04 (c) 2011-09-02 16:06
(u) Download and program application code
(q) query app code info
(g) execute app code
(r) refresh
9. Optional step: send q to check the program. The S caleCore will respond with a 
message that details the 32b checksum,  the product ID and version, and the 
application code version number in the following form:
Computed...

52    MSI-7300 Operator’s Manual
The MSI Limited Warranty
MEASUREMENT SYSTEMS INTERNATIONAL , INC., WARRANTS load sensing 
elements and meters against defects in workma nship and materials for a period of one year 
from date of purchase and warr ants electrical cables and batteries against the same defects 
for a period of ninety (90) days from date of purchase.
Any device which proves defective during the warr anty period will be replaced or repaired 
at 
 no charge; provided that the defective devi ce...

Appendix     53
Notes 

54    MSI-7300 Operator’s Manual
Notes 

A RICE LAKE WEIGHING SYSTEMS COMPANY
Measurement SystemsInternationalTM 
14240 Interurban Avenue South Suite 200 
”Seattle, WA 98168-4661 
”USA
Phone: 206-433-0199  
”Fax: 206-244-8470
www.ricelake.com   www.ricelake.mx   www.ricelake.eu   www.ricelake.co.i\
n   m.ricelake.com   
© Rice Lake Weighing Systems 11/2013152160 Rev B