Motorola Wing 5 Manual

SMART-RF-POLICY 21 - 19
21.1.12 smart-ocs-monitoring
smart-rf-policy
Applies smart Off Channel Scanning (OCS) instead of dedicated detectors
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
smart-ocs-monitoring {client-aware|extended-scan-frequency|frequency|
off-channel-duration|power-save-aware|sample-count|voice-aware}
smart-ocs-monitoring {client-aware [2.4GHz|5GHz] []}
smart-ocs-monitoring...

21 - 20 WiNG CLI Reference Guide
Parameters
• smart-ocs-monitoring {client-aware [2.4GHz|5GHz] []}
• smart-ocs-monitoring {extended-scan-frequency [2.4GHz|5GHz] []}
• smart-ocs-monitoring {frequency [2.4GHz|5GHz] []}
• smart-ocs-monitoring {off-channel-duration [2.4GHz|5GHz] []}
client-aware Optional. Enables client aware scanning on this Smart RF policy
Use this parameter to configure a client threshold number. When the number of clients 
connected to a radio equals this threshold number, the radio does...

SMART-RF-POLICY 21 - 21
• smart-ocs-monitoring {power-save-aware [2.4GHz|5GHz] [dynamic|strict]}
• smart-ocs-monitoring {sample-count [2.4GHz|5GHz] []}
• smart-ocs-monitoring {voice-aware [2.4GHz|5GHz] [dynamic|strict]}
Examples
rfs7000-37FABE(config-smart-rf-policy-test)#smart-ocs-monitoring extended-scan-
frequency 2.4Ghz 9
rfs7000-37FABE(config-smart-rf-policy-test)#smart-ocs-monitoring sample-count 2.4Ghz 
3
rfs7000-37FABE(config-smart-rf-policy-test)#smart-ocs-monitoring off-channel-
duration 2.4Ghz...

21 - 22 WiNG CLI Reference Guide
21.1.13 smart-ocs-monitoring (ap7161)
smart-rf-policy
Enables automatic channel selection on an AP7161 model access point, provided radio meshpoint is configured. Use this 
command to configure meshpoint on an AP7161.
Supported in the following platforms:
 AP7161
Syntax
smart-ocs-monitoring {client-aware|extended-scan-frequency|frequency|meshpoint|
off-channel-duration|power-save-aware|sample-count|voice-aware}
smart-ocs-monitoring {client-aware [2.4GHz|5GHz] []}...

CHAPTER 22 WIPS-POLICY
This chapter summarizes WIPS policy commands in detail.
The Wireless Intrusion Protection Systems (WIPS) is an additional measure of security designed to continuously monitor 
the network for threats and intrusions. Along with wireless VPNs, encryptions and authentication policies, WIPS enhances 
the security of a WLAN. 
The wireless controller supports WIPS through the use of sensor devices that locate unauthorized access points.
Use the (config) instance to configure WIPS policy...

22 - 2 WiNG CLI Reference Guide
22.1 wips-policy
WIPS-POLICY
Table 22.1 summarizes WIPS policy commands
Table 22.1wips-policy Commands
Command Description Reference
ap-detectionDefines the WIPS AP detection configurationpage 22-3
enableEnables a WIPS policypage 22-4
eventConfigures eventspage 22-5
history-throttle-
durationConfigures the duration event duplicates are omitted from the event 
historypage 22-9
noNegates a command or sets its defaultpage 22-10
signatureConfigures signaturepage 22-14...

WIPS-POLICY 22 - 3
22.1.1 ap-detection
wips-policy
Enables the detection of unauthorized or unsanctioned APs. Unauthorized APs are untrusted access points connected to 
an access point managed network. These untrusted APs accept wireless client associations. It is important to detect such 
rogue APs and declare them unauthorized.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
ap-detection {ageout|wait-time}...

22 - 4 WiNG CLI Reference Guide
22.1.2 enable
wips-policy
Associates this WIPS policy with a wireless controller profile
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
enable
Parameters
None
Examples
rfs7000-37FABE(config-wips-policy-test)#enable
rfs7000-37FABE(config-wips-policy-test)#
Related Commands
noDisables a WIPS policy from use with a wireless controller profile 

WIPS-POLICY 22 - 5
22.1.3 event
wips-policy
Configures events, filters and threshold values for this WIPS policy. Events have been grouped into three categories, 
AP anomaly, client anomaly, and excessive. WLANs are baselined for matching criteria. Any deviation from this baseline 
is considered an anomaly and logged as an event.
Supported in the following platforms:
 AP300
 AP621
 AP650
 AP6511
 AP6521
 AP6532
 AP71XX
 RFS4000
 RFS6000
 RFS7000
 NX9000
 NX9500
Syntax
event...

22 - 6 WiNG CLI Reference Guide
Parameters
• event ap-anomaly [ad-hoc-violation|airjack|ap-ssid-broadcast-in-beacon|
asleap|impersonation-attack|null-probe-response|
transmitting-device-using-invalid-mac|unencrypted-wired-leakage|wireless-bridge]
• event client-anomaly [crackable-wep-iv-key-used|dos-broadcast-deauth|
fuzzing-all-zero-macs|fuzzing-invalid-frame-type|fuzzing-invalid-mgmt-frames|
fuzzing-invalid-seq-num|identical-src-and-dest-addr|invalid-8021x-frames|...