Motorola Mth500 Basic 6802963c65 Manual

11
MTH500 Portable Radio Basic Service Manual - TEST SETUP & TESTING
Note: The displayed values are factory defaults and should not be changed.
NEIGHBOUR CELL BROADCAST: NOT REQUIRED
BROADCAST INTERVAL: 10s
NEIGHBOUR CELL CHANNEL: 0000
NEIGHBOUR CELL LOCATION AREA: 00000
NEIGHBOUR CELL IDENTIFIER: 01
SLOW RE-SELECT THRESHOLD: 10dB
PRESS “MORE” SOFT KEY
SLOW RE-SELECT HYSTERESIS: 10dB
FAST RE-SELECT THRESHOLD: 10dB
FAST RE-SELECT HYSTERESIS: 10dB
22. Press the “Return” soft key.
23. Press the “Trunk Type”...

TEST SETUP & TESTING:  RF Tests
12
3. Press “Traffic Channel” soft key. Enter “3700” for R1 and “900” for R2 and 
press “Traffic Channel” soft key. The marker goes to Timeslot. Enter “3” and 
press “Traffic Channel” soft key. (Note that the Traffic Channel number 
changes automatically after entering the Control Channel number).
4. Press “RF Gen Level” soft key. Thereafter, enter “-50” and press “dBm” data 
keys followed by “RF Gen Level” soft key.
5. Press “Mobile Power” soft key, enter 30 dBm/1W, using...

13
MTH500 Portable Radio Basic Service Manual - TEST SETUP & TESTING
2. Before testing, the radio should be configured to RSSI mode using the follow-
ing Sequence, When performing steps 3 thru 6, make sure that you press the 
handset keys sequentially (less then a second between every consecutive 
press). 
3. Press the “Volume down” Key.
4. Press the “1 “key, and “Menu” Key.
5. Press the “2 “key, and “Menu” Key.
6. Press the “3 “key. 
Hereafter, there is no need for quick sequence of pressing the handset...

TEST SETUP & TESTING:  Call Processing Test
14
15. Press “Back” twice using the Left (.) Key.
Transmitter Tests
1. Change the “Mode Key” of the radio to “Group Mode”.
2. Press the “RF Gen Level” soft key. Enter “-90dBm” by pressing the data keys 
and “RF Gen Level” Key.
3. Press the “PTT” of the radio and monitor the IFR “Manual Test” screen which 
displays the Burst Power, Power Profile, Timing Error, Vector Error, and Fre-
quency Error. 
Note: You have to hold the PTT in the pressed position long...

15
MTH500 Portable Radio Basic Service Manual - TEST SETUP & TESTING
2. Press the “Test Sound” soft key to provide the 1kHz signal to the radio 
speaker.
3. Press the “Silence” soft key to mute the 1KHz Audio Signal of the speaker.
4. Press the “Clear Down” soft key and check that the “Cleardown Complete” 
status appear on the IFR “Manual Test” screen.
Call to Mobile
1. Press the radio “Mode” key and change to “Private” mode.
2. Press the “Call Mobile” soft key on the IFR.
Note: Select type of call.
3....

16
3. Speak into the Handset Microphone and hear your speech (after a short delay) 
from the handset Earpiece.
Note: If you need more details, press the “Duplex Test” mode key.
4. Press the “duplex test (Tx)” soft key twice. The “Digital Duplex test” results 
will be displayed on the IFR screen providing you with the following bar 
charts measurement capabilities:
    - Power
    - Vector RMS
    - Frequency Error 
 For Power Analyser Graph:
5. Press “power ana” soft key.
6. Check that the power frame...

17
MTH500 Portable Radio Basic Service Manual - TEST SETUP & TESTING
DMO Test 
IFR 2968 Test Setup
1. Press the “System” softkey.
2. Press “TETRA Direct” Softkey.
3. Press “Setup” Softkey.
4. Press “Channel Plan” Softkey, press “TETRA 380+ODM” softkey for R1or 
TETRA 410+ODM for R2.
5. Press DM Tx Mode” softkey, press “discontinue” softkey
How to Configure the IFR 2968 Manual Test Screen
1. Press the “Manual” softkey.
2. Press “Channel” Softkey, thereafter enter “4000= 390 MHz” for R1or 
“1200=420 MHz...

TEST SETUP & TESTING:  DMO Test
18
RF Test - Transmit Test
Hold the PTT in the pressed position long enough to enable you to read the 
results:
•Results:    - Power Profile: Passed
•Burst Power Request Results: 28-32 dBm
•Frequency Error: +/- 100Hz max.
•Vector Error: Max. 10% RMS, Max. 30% Peak, Max. 5% Residual. 

19
MTH500 Portable Radio Basic Service Manual  - PROGRAMMING THE RADIO
CHAPTER 3
 PROGRAMMING THE RADIO
Before Using the Customer Programming Software 
(CPS)
Before you begin programming, ensure the following:
•That your radio battery is fully charged.
•That you have connected the Data cable (FKN4897), according to Figure 2.
•That the Customer Programming Software (CPS) is installed in your computer.
 
Figure 2.  Setup for Radio Programming.
MTH500Radio
p
Serial Port
(COM1/2)
To MTH500
Accessory...

PROGRAMMING THE RADIO:  Programming the Radio
20
Programming the Radio
1. Verify that the radio is turned off.
2. Run the Customer Programming Software (CPS) on your computer.
3. Press the “1” and “9” keys together and then the On/Off key for about 3 sec-
onds. Verify that no display appears on the LCD screen.
4. Click the Toolbar “Read Phone” icon. Refer to the CPS Application Window 
Screen in the CPS User Guide, Publication No. 68P02956C20. The setup 
enters an initialization process that takes about...