Motorola Minitor 6 Manual

Pager Programming Software (PPS)27
English
•The pager monitors any activity on 
both frequencies. If activity is 
detected on either frequency, the 
receiver will lock on to that frequency 
until the transmission ends.
Note: Neither frequency will have 
monitoring precedence over the other.•When the pager is locked on to either 
of the scanned frequencies, the pager 
will sound an alert to the correct 
address tones for that frequency and 
start message storage. The pager will 
turn the audio off...

Pager Programming Software (PPS)English28
•At this time the receiver will resume 
the priority scan activity. The pager 
will only alert on the detection of alert 
tones on the priority frequency. The 
pager will then turn the audio off 
according to the current Reset mode. 
Address detection is turned off for the 
non-priority frequency.
•Silent Scan:•This mode allows you to monitor 
traffic on two different frequencies.
Note: Neither frequency will have 
monitoring precedence over the other.•The...

Pager Programming Software (PPS)29
English
•Vibrate: The pager vibrates.•To n e  &  V i b r a t e: The pager plays a tone 
and vibrates simultaneously.
Note: While the pager is in the Amplifier 
Charger it will not alert if it is set to vibrate.
Announcements
When the Function Switch announcements 
are enabled, you can set the type of 
announcements to be played. These 
announcements are played when the pager 
is powered up or when the Function Switch 
is moved to a new position.There are three different...

Pager Programming Software (PPS)English30
Enable On/Off Duty
This option is available for Selective Call 
and Silent Scan modes only. It allows you 
to program a specific address as Off Duty, 
thereby ignoring that address. By clicking 
on the checkbox, the on or off selection 
gets enabled in the corresponding channel 
tab.
Note: While programming the addressed 
as on or off for any channel position, at 
least one address must be programmed as 
On Duty.Push-To-Listen
This option is available for...

Pager Programming Software (PPS)31
English
Channel Options
You can program up to five different 
receiving frequencies and their 
corresponding parameters like bandwidth, 
tone system, and coding option.
Channel Bandwidth
The pager can operate on 12.5 KHz 
Channel Spacing (Narrowband) or 25 KHz 
Channel Spacing (Wideband).Reset Function
Sets the method to reset the pager after 
receiving a page. There are eight different 
reset functions available.
•Automatic: Resets the pager when 
carrier...

Pager Programming Software (PPS)English32
•Delayed Revert: Waits momentarily 
before checking for carrier drop and 
then reverts to Monitor mode.•Muted Delayed Revert: Waits 
momentarily before checking for carrier 
drop and then reverts to Monitor mode. 
During the momentary wait period 
mutes the speaker and stored voice 
recording during carrier drop. •Time-out: Resets the pager after a 
preprogrammed amount of time.•Manual: Audio remains turned on until 
the Reset button is pressed while in...

Stored Voice Features and Controls33
English
Stored Voice Features 
and ControlsThe pager can store at least 8 minutes of 
voice messages. Messages are stored 
according to their length. If preferred, the 
pager can be programmed to store 
messages in fixed lengths of 30, 60, or 120 
seconds instead. Minitor VI provides a list 
of controls for stored message 
management – fast forward, rewind, skip to 
next, return to previous, lock, unlock, and 
delete all.
Stored Voice OperationThe message is stored...

Stored Voice Features and ControlsEnglish34
• When the Timed-out Reset cycle is 
complete.
Note: If channel traffic occurs after the 
page and message, and before carrier 
signal is lost, that will also be stored in 
memory. Stored Message ManagementYour pager offers extended capability to 
manage the stored messages. There are 
three multifunction buttons available on the 
front side of device for message 
management.Playback 
ButtonPress the Playback button to 
playback a particular message 
stored in...

Stored Voice Features and Controls35
English
Note: Press and hold the Fast Forward 
and Rewind buttons simultaneously to 
delete all stored unlocked messages. You 
need to unlock a locked message before 
you can delete it. Fast 
Forward 
ButtonPress the Fast Forward button 
to skip to the next message or 
to fast forward the current 
message.
•Press to skip to the next 
message.•Press and hold to fast 
forward the current 
message.Rewind 
ButtonPress the Rewind button to 
return to the previous 
message...

Cleaning Your PagerEnglish36
Cleaning Your PagerTo clean smudges and grime from the 
exterior of your pager, use a soft, 
non-abrasive cloth moistened in a mild 
soap and water solution. Use a second 
cloth moistened in clean water to wipe the 
surface clean. Do not immerse in water. Do 
not use alcohol or other cleaning solutions.Repair and MaintenanceYour pager, properly handled, will provide 
quality service for years. However, should 
it ever require service, call 1-800-548-9954 
for instructions....