Motorola Micom 2 Manual

							MICOM-2E-ALE Owner’s Manual
38
Setting the Band Width
MICOM-2E offers four band width options:
· 2700
· 3300
· LSM - Low Speed Modem
· CW - Continuous Wave
To set the channel band width:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[CHAN].
3.Presstwice to scroll to the BW option.
4.Press[BW].
5.Press the function key beneath the band width of your choice.
6.Press
 to confirm,to cancel. 
						

							Programming the Radio
39
Setting Radio Parameters
Baud Rate (BAUD)
MICOM-2E offers four baud rate options:
· 1.2 - 1200 bps
· 2.4 - 2400 bps
· 4.8 - 4800 bps
· 9.6 - 9600 bps
To set the baud rate:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[PRMT].
3.Press[BAUD].
4.Press the function key beneath the baud rate of your choice:
1.2 = BAUD - 1200
2.4 = BAUD - 2400
4.8 = BAUD - 4800
9.6 = BAUD - 9600
5.Press
 to confirm,to cancel. 
						

							MICOM-2E-ALE Owner’s Manual
40
Data Power (DPWR)
MICOM-2E offers four data power levels:
· LOW
· MED
· HIGH
· MAX
To set the data power level:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[PRMT], Radio Parameters.
3.Press[DPWR], Data Power.
4.Press the function key beneath the DT power level of your choice.
5.Press
 to confirm,to cancel. 
						

							Programming the Radio
41
Microphone Side Tone (MST)
This menu toggles between enabling and disabling the microphone
sidetone.
Press
[YES] to enable the microphone sidetone.
Press
[NO] to disable the microphone sidetone.
Press
 to confirm,to cancel.
Accessory Side Tone (AST)
This menu toggles between enabling and disabling the accessory side
tone.
Press
[YES] to enable the accessory sidetone.
Press
[NO] to disable the accessory sidetone.
Press
 to confirm,to cancel.
PTT Release Beep (PTBP)
This menu toggles between enabling and disabling the beep for the
push-to-talk (PTT) button.
Press
[YES] to enable the beep.
Press
[NO] to disable the beep.
Press
 to confirm,to cancel. 
						

							MICOM-2E-ALE Owner’s Manual
42
Keyboard Beep (KBBP)
This menu toggles between enabling and disabling the beep for the
keyboard (keypad).
Press
[YES] to enable the keypad
beep.
Press
[NO] to disable the keypad beep.
Press
to confirm,to cancel.
Tone
This menu sets the keyboard beep tone to high or low volume.
Press
[YES] to set to low volume.
Press
[NO] to set to high volume.
Press
to confirm,to cancel. 
						

							Programming the Radio
43
Alternate Display Time-out (ADT)
This menu sets the time-out time of the menu display. You define the
number of seconds that elapse before the display returns to the
previous screen.
To set the time-out time:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[PRMT].
3.Pressto scroll to the ADT option.
4.Press[ADT].
5.Press
Press
Press
Press[] to increment the displayed value by 1.
[1], to quick-set the value to 1.
[10], to quick-set the value to 10.
6.Press
 to confirm,to cancel. 
						

							MICOM-2E-ALE Owner’s Manual
44
Setting Radio Options
MICOM-2E offers three programmable radio options:
· Tuner (TUNE)
· Accessory (ACC)
· ALE
To set the radio option:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[OPTS].
3.Press the function key beneath the option of your choice:
TUNE - toggles the tuner.
ACC - sets the accessory setting.
ALE - toggles ALE option on/off.
4.Press to confirm,to cancel. 
						

							29
Programming the Radio
MICOM-2E is already configured for use at the time of purchase.
However, at times, it is necessary to change the configuration. The
following sections relate to MICOM-2E’s Programming mode.
You can find your radio parameter and change it by pressing a
function key under the parameter name, or you can press
the scroll arrow keys to scroll through the parameters.
To enter Programming mode:
1.Pressto display the Menu screen.
2.Pressto scroll to the second Menu screen.
3.Press[PROG] to enter Program mode.
4.Press
mode.[RAD] to enter Radio Programming
In this menu, you program:
· channels
· radio parameters
· radio options
The following sections explain the programming procedures in detail. 
						

							MICOM-2E-ALE Owner’s Manual
30
Programming Channels
When you choose the CHAN option in the Radio Programming menu,
you see a menu with the following options:
· GET - Get programmed channel
· STOR - Store channel
· ERAS - Erase programmed channel
· PWR - Tx power level
· FREQ - Frequency
· BAND - Band type
· MODE - Radio mode
· AGC - Automatic Gain Control
· BW - Band width
The use of each option is explained in the following sections.
Channel Options
The first three options, GET, STOR, and ERAS, are used for
programming channels in MICOM-2E.
GET retrieves channels already programmed in MICOM-2E. Once a
channel is programmed in MICOM-2E, it is stored with all its
parameters. Retrieving a channel retrieves all the parameters defined
for the channel. 
						

							Programming the Radio
31
To copy a channel’s parameters to another channel:
1.Enter the Radio Programming menu (steps 1-4 on
page 29).
2.Press[CHAN].
3.Press[GET].
4.Enter the number of the channel to which you want
to copy the parameters with the keypad.
5.Select the source channel.
6.Press
[STOR].
Note that the channel number is flashing, which indicates that you can
change it or leave it at the current number.
7.Enter the number of the channel to which you want
to copy the parameters with the keypad.
If you need to backspace, press  [BACK].
If you want to clear the display, press 
 [CLR].
8.Press
 to confirm.