Motorola Gr300 Zr310 Community Repeater 6880902z68 C Manual

 
Section 6 
Programming 
 
The ZR310 will reference the system ID user for the proper TPL/DPL encode and the Morse ID to send. You can use a disabled or enabled 
user number. 
The Morse code station ID is sent after a 0.75 second key up delay.
 
Carrier Only Repeat (Open Repeater) 
You can program the ZR310 to repeat based on just the carrier, sometimes called carrier controlled repeat, or open repeater. In this mode, 
the ZR310 provides simultaneous tone/open repeater operation for users that have TPL...

 
Section 6 
Programming 
User Programmable Fields 
Enable a User 
To activate a user in the ZR310, you must enable the TPL tone or DPL code user number. The transmit radio keys when the carrier and the 
TPL tone or DPL code are decoded. 
Set the Status line as Enable to activate a user.
 
Reserve a User 
You may need to reserve a TPL tone or DPL code for future use. If a user keys up on a reserved user number, the transmitter will be keyed 
but it does not cut through a repeat audio. It sends a beep...

 
Section 6 
Programming 
View All Users 
To view the user numbers 
1. Press F6 to view all  
Figure 6-9 is the TPL User Screen, which shows users 1-50. Figure 6-10 is the DPL User Screen, which shows users 51-70. 
NOTE 
The F6 key will now toggle between the TPL User and 
the DPL User Screens. 
 
Figure 6-9. TPL Users 
Radio Parameters 
From the Main Menu 
1.  Press F4 to see the Change / View Menu.  
2.  Press F5 for the Mode screen.  
This screen will vary, depending on the type of repeater option...

 
Section 6 
Programming 
 
 
Figure 6-100. DPL Users 
Figure 6-11. Cant do 
Figure 6-12. Cant do 
Low Battery Alert 
To program the repeater to send out a warning signal when its battery gets low: 
1.  From the Main Menu, press F4 to see the Change/View Menu.  
2.  Press F7 to access the Signalling Menu.  
3.  Press F2 to see the screen in Figure 6-13.  
4.  Using the arrow keys, move the cursor to the space next to Low Battery.  
5.  Using the up/down arrows, choose Y to set the low battery alarm on....

 
Section 6 
Programming 
 
 
Figure 6-14. Radio Wide Accessory Screen 
4. Set the desired custom information. 
5. Press F10 to exit.
 
CAUTION 
Repeater mode will not keep custom information. 
Therefore, if you customize your radios, you may limit 
yoursel f to always programming in radio mode. 
For more information, refer to the Basic RSS Manual. 
Programming Over-The-Air 
You can program the ZR310 using a portable radio with a DTMF keypad. While programming the unit. it is helpful, but not required,...

 
Section 6 
Programming 
 
The following steps describe how to enter the programming mode: 
1. Enter a program mode access code. 
2. Press the # key. 
NOTE 
The default access code is 12310# 
3. Listen for three chirps, which indicate proper access. 
Exiting the Program Mode 
The following steps describe how to exit the program mode: 
1. Enter 99. 
2. Press the # key. 
3. Listen for the ringing prompt tone, which confirms that you have exited program mode.
 
Entering a Command 
The following steps...

 
Section 6 
Programming 
Program Mode Access Code 
The following paragraphs describe the system, user and diagnostic commands available for the ZR310 when programming over-the-air or 
via telephone. These include the options available with RSS programming. For detailed information about each option, refer to the 
paragraphs under Programming Via Radio Service Software (RSS) on page 6-1. Enter each command as described in the Programming 
Over-The-Air on page 6-7. 
System Commands 
Repeater...

 
Section 6 
Programming 
Carrier Repeat (CSQ) User 
1. Enter 203#.  
2.  Enter the CSQ user number uu# (0-70).  
Example: 
203# 49# - CSQ users repeat as user 49
 
Courtesy Tone 
1. Enter 209#.  
2.  Enter the beep frequency ffff# in Hz (400-2500).  
Example: 
209# 1200# - Set courtesy tone to 1200 Hz
 
System ID User 
1. Enter 208#.  
2.  Enter the user number uu# (0-70, where 0 = off).  
Example: 
208# 49# Sets user 49 as the system user.
 
Station ID Frequency 
1. Enter 206#.  
2.  Enter the...

 
Section 6 
Programming 
Station ID Speed 
1. Enter 207#.  
2.  Enter speed ss# in words per minutes (4-25, Default = 22).  
Example: 
207# 15# - Set station IS speed to 15 minutes.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
March, 1993  6880902Z68-O  Section 6-18
  

 
Appendix A 
DTMF Commands 
 
Table A-1. DTMF System Commands 
Command Function Parmeter 
201# t# 
202# tt# Set stuck mic timeout timer to t minutes 
Set anti-kerchunker filter timer to t.t seconds t=1-9 minutes 
tt=0.1-5.0 seconds (0=disable) 
203# uu# 
204# nn# Set CSQ user number uu 
Accessor y PTT TPL/DPL, 0=off uu=0-70 
nn=50 for TPL, 1000-1777 for DPL
205# tt# 
206# ffff# 
207# ss# 
208# uu# Set station ID interval to tt 
Set station ID tone frequency to ffff Hz 
Set station ID speed to ss WPM...