Motorola Gm Series Detailed 6864115b62 B Manual

UHF (403-470MHz) Frequency Synthesis2-7
A voltage of 5V applied to the super filter input (U4201 pin 30) supplies an output voltage of 4.5 
VDC(VSF) at pin 28. It supplies the VCO, VCO modulation bias circuit (via R4322) and the 
synthesizer charge pump resistor network (R4251, R4252). The synthesizer supply voltage is 
provided by the 5V regulator U4211.
In order to generate a high voltage to supply the phase detector (charge pump) output stage at pin 
VCP (U4201-47), a voltage of 13 VDC is being...

2-8THEORY OF OPERATION
The VCOBIC together with Fractional-N synthesizer (U4201) generates the required frequencies in 
both  transmit and receive modes. The TRB line (U4301 pin 19) determines which tank circuits and 
internal buffers are to be enabled. A high level on TRB enables TX tank and TX output (pin 10), and  
a low enables RX tank and RX output (pin 8). A sample of the signal from the enabled output is 
routed from U4301 pin 12 (PRESC_OUT), via a low pass filter, to pin 32 of U4201 (PREIN).
A...

UHF (403-470MHz) Transmitter Power Amplifier (PA) 40W 2-9
5.0 UHF (403-470MHz) Transmitter Power Amplifier (PA) 40W
The radio’s 40 W PA is a four stage amplifier used to amplify the output from the VCOBIC to the radio 
transmit level. It consists of the following four stages in the line-up. The first stage is a LDMOS 
predriver (U4401) that is controlled by pin 4 of PCIC (U4501) via Q4473 (CNTLVLTG). It is followed 
by another LDMOS stage (Q4421), an LDMOS stage (Q4431) and a bipolar final stage (Q4441)....

2-10THEORY OF OPERATION
5.3 Driver Stage
The following stage is an enhancement-mode N-Channel MOSFET device (Q4431) providing a gain 
of 10dB. This device also requires a positive gate bias and a quiescent current flow for proper 
operation. The voltage of the line Bias_2_UHF_PA_1 is set in transmit mode by the ASFIC and fed to 
the gate of Q4431 via the resistive network R4632, R4631, R4485 and R4486. This bias voltage is 
also tuned in the factory. If the transistor is replaced, the bias voltage must be...

UHF (403-470MHz) Transmitter Power Amplifier (PA) 40W 2-11
5.8 Power Control
The transmitter uses the Power Control IC (PCIC, U4501) to control the power output of the radio. A 
portion of the forward RF power from the transmitter is sampled by the bi-directional coupler and 
rectified, to provide a DC voltage to the RFIN port of the PCIC (pin 1) which is proportional to the 
sampled RF power. 
The PCIC has internal digital to analog converters (DACs) which provide the reference voltage of the 
control...

2-12THEORY OF OPERATION 

Chapter 3
TROUBLESHOOTING CHARTS
1.0 Troubleshooting Flow Chart for Receiver (Sheet 1 of 2)
Bad SINAD
Bad 20dB Quieting
No Recovered AudioSTART
Audio at 
pin 8 of 
U3101 ?Check Controller
(in the case of no audio)
OR ELSE go to “B” Ye s
No
Spray or inject 44.85MHz 
into XTAL Filter FL3101
Audio heard ?BYe s
No
Check 2nd LO 
(44.395MHz) at C3135 
LO present ?BYe s
 Check voltages on 
U3101Biasing OK ?
No
No
A
Ye s
Check Q3102  bias 
for faults
Replace Q3102
Go to B
Ye s
No
Check circuitry 
around U3101....

3-2TROUBLESHOOTING CHARTS
1.1Troubleshooting Flow Chart for Receiver (Sheet 2 of 2)
IF Signal at 
C3101?
No
RF 
Signal at 
T4051?
RF
Signal at 
C4015?
No
No
RF
Signal at 
C4025?
No or 
Check harmonic filter
L4491-L4493, C4492, J4401
and ant.switch
D4471, D4472, L4472.
Check filter between 
C4025 & C4009. 
Check tuning voltage 
at R4060.
Inject RF into J4401
Is
tuning voltage
OK?
No
Ye s
Check RF amp (Q4003) 
Stage.
Check filter between 
C4015 & T4051.
Ye s
Check T4051, T4052, 
D4051, R4052, L4008.
Ye s
1st...

Troubleshooting Flow Chart for 25W Transmitter (Sheet 1 of 3) 3-3
2.0 Troubleshooting Flow Chart for 25W Transmitter (Sheet 1 of 3)
Current 
increase 
when keyed?
NO YES
START
Check if Pressure Pad closes S5440
Check Components between 
Q4441 and RF Output, 
Antenna Switch 
D4471,D4472,Q4472, >500mA & 4A
1V
Short TP4403 to 
Ground
NO
YES
Voltage at 
TP4402 
rises?Check PA StagesNO
YES
PCIC U4501 
Pin 14 9.3V 
DC?Check 9.3 V Regulator 
U0641
NO
YESPCIC U4501 
Pin 16 >4V 
DCReplace PCIC U4501
NO
YESTP4404...

3-4TROUBLESHOOTING CHARTS
2.1Troubleshooting Flow Chart for 25W Transmitter (Sheet 2 of 3)
Check PA Stages
No or too low Power when keyed
Measure DC Voltage at Pin 2 & 3 of U4401>6 YESDC Voltage 
at U4501 
Pin 23 =0?
2-6DC Voltage 
at U4402-1 
Pin 1?
YESPin 2
Voltage 0.62 
* Voltage at 
Pin 1?
If U4201 Pin 2 is high,  
replace PCIC
NOReplace U4401
YES NODC 
Voltage at 
U4402-1 Pin 
3 = 8.8V?
Check S4440, 
R4442 and R4443
YESPin 3 
Voltage 0.51 
* Voltage at 
Pin 1?
NOReplace U4401
6V
Check Components...