Motorola Dp3400 3401 3600 3601 Mototrbo Basic 6866574d29 E Manual

Introduction: Specifications 1-11
 UHF1 Self-Quieter Frequencies
GPS Non-GPS
403.20 MHz ± 5k
409.23 MHz ± 5k –
414.00 MHz
417.79 MHz ± 10k 420.00 MHz ± 5k
425.60 MHz ± 5k –
431.10 MHz ± 5k
432.00 MHz ± 5k
436.80 MHz ± 5k
441.97 MHz ± 5k –
442.36 MHz ± 10k 444.00 MHz ± 5k 450.00 MHz
453.60 MHz ± 5k
458.34 MHz ± 5k –
466.93 MHz ± 10k 468.00 MHz ± 5k
 VHF Self-Quieter Frequencies
GPS Non-GPS
144.000 MHz ± 100k
147.320 MHz ± 5k –
147.455 MHz ± 10k 151.200 MHz ± 5k
156.000 MHz ± 10k
162.000 MHz ± 10k
163.690...

1-12Introduction: Specifications
 UHF2 Self-Quieter Frequencies
GPS Non-GPS
450.000 MHz
453.600 MHz ± 5k
458.340 MHz ± 5k –
466.930 MHz ± 10k 468.000 MHz ± 5k
470.400 MHz ± 5k
474.701 MHz ± 10k –
480.000 MHz ± 5k
486.000 MHz ± 15k 487.200 MHz ± 5k
491.070 MHz ± 10k –
491.520 MHz ± 10k 502.200 MHz ± 5k
504.000 MHz ± 15k 506.695 MHz ± 5k
507.439 MHz ± 15k – 

Introduction: Specifications 1-13
GPSDisplay 
DP 3600/ DP 3601Non-Display 
DP 3400/ DP 3401
TTFF (Time To First Fix) Cold Start  <  1  minute 
TTFF (Time To First Fix) Hot Start  < 10 seconds 
Horizontal Accuracy  < 10 meters 
Accuracy specs are for long-term tracking (95th percen tile values > 5 satellites visible at a nominal 
-130 dBm signal strength) 
  Military Standards
Applicable MIL–STD  810E 810F 
Methods Procedures  Methods Procedures 
Low Pressure  500.3  II 500.4  II 
High Temperature  501.3...

1-14Introduction: Specifications
* -Operating temperature specification  with LiIon battery is -10°C to +60°C.
-Operating temperature specification  with NiMH battery is -20°C to +60°C.
Conforms to:
MOTOTRBO Portable series radios meet FM (Facto ry Mutual) standards for intrinsic safety used in
Class I, II, III, Division 1, Groups C, D, E, F,  and G when properly equipped with a Motorola FM
approved battery option. They are also approved for  nonincendive use in Class I, Division 2, Groups
A, B, C, and...

Chapter 2 Test Equipment and Service Aids
2.1 Recommended Test Equipment
The list of equipment contained in Table 2-1 includes most of the standard test equipment required 
for servicing Motorola portable radios.
Table 2-1.  Recommended Test Equipment
Equipment Characteristics ExampleApplication
Service
MonitorCan be used as a substi-
tute for items marked with 
an asterisk (*)Aeroflex 2975 
(www.aeroflex.com), 
Motorola R2670, or equivalentFrequency/deviation meter and 
signal generator for wide-range...

2-2Test Equipment and Service Aids: Service Aids
2.2 Service Aids
Table 2-2 lists the service aids recommended for wo rking on the radio. While all of these items are 
available from Motorola, most are standard worksh op equipment items, and any equivalent item 
capable of the same performance may be substituted for the item listed.
Table 2-2.  Service Aids
Motorola Part No. Description Application
RLN4460_Portable Test SetEnables connection to the audio/accessory jack. 
Allows switching for radio...

Test Equipment and Service Aids: Programming, Testing and Alignment Cable 2-3
2.3 Programming, Testing and Alignment Cable
Figure 2-1.  Programming, Testing and Alignment Cable
#1
#14
#25
#13 #4
#1
#2 #12
#11 #1P1
P2
P3 

2-4Test Equipment and Service Aids: Programming, Testing and Alignment Cable
Figure 2-2.  Pin Layout of Side Connector
Table 2-3.  Pin Configuration of Side Connector
CONNECTION
P1 P2
P3
Pin Pin Pin Function
13 VCC (5V)
34D ATA  +
25D ATA  -
16
6 GROUND
7
8 SPEAKER -
17
10 EXTERNAL MIC +
16
11 EXTERNAL MIC -
20
9 EXTERNAL PTT
1
7 SPEAKER +
41 (Coax 
Connector) GROUND
slot for accessory
connector  hook
Coaxial RF Connector
1
2
3
4
5
6
7
8
9
10
11
12
GPI O_0
Spkr +
Spkr -
Mic + Mic -
GPI
O_3
GPI O_4...

Chapter 3 Transceiver Performance Testing
3.1 General
These radios meet published specifications through their manu facturing process by utilizing high- 
accuracy laboratory-quality test equipment. Th e recommended field service equipment approaches 
the accuracy of the manufacturing equipment  with few exceptions. This accuracy must be 
maintained in compliance with the manufacturer’s recommended calibration schedule.
Although these radios function in digital and a nalog modes, all testing is done in...

3-2Transceiver Performance Testing Setup
Oscilloscope Source: Mod
Oscilloscope Horizontal: 10mSec/Div
Oscilloscope Vertical: 2.5kHz/Div
Oscilloscope Trigger: Auto
Monitor Image: Hi
Monitor Bandwidth: Narrow
Monitor Squelch: Middle setting
Monitor Vol: 1/4 setting Current: 2.5A
Table 3-1.  Initial Equipment Control Settings
Service Monitor
Power Supply Test Set