Mitsubishi Xd3500u Dlp Projector User Manual

EN-41
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network. 
•  To supervise and control the projector, install the software “Projector-Control Device Installer *” contained in the 
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control 
Utility” contained in the attached CD-ROM. 
 *) Functions
•  Setting of the projector’s IP address
•  Setting of password, display...

EN-42
Indicators
This projector has 2 indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your 
dealer. 
POWER indicator STATUS indicator
Normal condition
POWERSTATUS CONDITION NOTE
Steady
red
OffStand-by
Blinking
greenLamp stand-by for power-offThe power cannot be turned on by pressing 
the POWER button.
Steady
green
Blinking
greenLamp stand-by for power-on The power...

EN-43
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. 
Spare lamp  VLT-XD3200LP
Warning:
•  Be careful not to drop the lamp fi xing screws into the inside of the projector. Don’t put...

EN-44
Replacing the lamp (continued)
To replace the lamp:
1.  Turn off the main power switch and unplug the 
power cord. 
2.  Loosen the screw (a) using a Phillips screwdriver 
(+), and remove the lamp cover (b).
(a)(b
)
3.  Loosen the screws (c) using a Phillips screwdriver 
(+).
(c)
4.  Pull the handle.
5.  Pull out the lamp box by the handle while holding 
the projector.
•  Pull the lamp box out of the projector slowly. 
If it is pulled out quickly, the lamp may break 
scattering glass fragments.
•...

EN-45
When removing the lamp from the ceiling-mounted projector
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the 
projector or option lamp to prevent glass fragments from scattering.
•  Assemble the lamp replacement tray according to the procedure shown on it.
1.  Follow steps 1 to 4 on page 44.
2.  Attach the lamp replacement tray to the projector as shown in the 
fi gure.
3.  Secure the lamp replacement tray on the projector using the tape 
packed...

EN-46
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be 
sure to unplug the power plug, and then contact your dealer. 
No image appears on the screen. 
Problem Solution
Power can not be 
turned on.•  Check whether the indicators are on or off and how they are lightning.
POWER STATUS Solution
OffOff
•  Connect the power cord to the projector.
•  Plug the power cord into a wall outlet.
•  Turn on the main power switch.
•...

EN-47
Troubleshooting (continued)
No image appears on the screen. (continued) 
Problem Solution
“NO SIGNAL” is 
displayed.•  Turn on the power of the connected device, or check whether there is something 
wrong with the connected device.
•  Check whether the external device output signals. (Check this especially when the 
external device is a notebook computer.) 
•  Check that the cable connected to the external device isn’t defective. 
•  Check that the projector is connected to the external device...

EN-48
Troubleshooting (continued)
Images are not displayed correctly. (continued) 
Problem Solution
Different color tint. •  When comparing images projected by two projectors, tints in the displayed images 
may be different because of variation between their optical components. This is not a 
malfunction. 
•  When comparing the image projected by this projector with those displayed on the 
television or PC monitor, tints in the displayed images may be different because of 
difference in the range of...

EN-49
Troubleshooting (continued)
If the following problem occurs after the lamp is replaced, check the following fi rst. 
Problem Solution
The projector does not 
turn on. •  Fit the lamp cover securely. (See pages 43 and 44.)  
•  Reset the lamp operating time. (See page 44.)
The STATUS indicator 
blinks.•  Reset the lamp operating time. (See page 44.)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. 
Refer to the information...

EN-50
Specifi cations
The specifi cations and outside appearance of the projector are subject to change without prior notice.
Type DLP™ projector
Model XD3500U
Display technology 0.7-inch Single chip DMD
Pixel 1024 x 768 = 786432 pixels
Projection lens F 2.0 - 2.4  f= 24.5 - 33.1 mm
Light-source lamp 330 W
Image size (projection distance)40” min. to 300” max. (projection distance 1.4 to 10.6 m)
Maximum resolution Computer signalMaximum resolution:  1600 x 1200 dots (compressed)
Panel resolution: 1024 x 768...