Mitsubishi Xd3500u Dlp Projector User Manual

XD3500
This User Manual is important to you.
Please read it before using your projector.
DLP™ PROJECTOR
MODEL
XD3500U
User Manual 

EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.
The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert 
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure 
that may be of suffi cient magnitude to constitute a risk of electric shock.
The exclamation point within an...

EN-3
Contents
Important safeguards ........................................................................................................................ 4
Preparing your projector .................................................................................................................... 6
Using the remote control ................................................................................................................... 9
Setting up your projector...

EN-4
Important safeguards
Please read all these instructions regarding your 
projector and retain them for future reference. Follow 
all warnings and instructions marked on the projector.
1. Read instructions
  All the safety and operating instructions should be 
read before the appliance is operated.
2. Retain instructions
  The safety and operating instructions should be 
retained for future reference.
3. Warnings
  All warnings on the appliance and in the operating 
instructions should be adhered to....

EN-5
Important safeguards (continued)
WARNING:
Unplug immediately if there is something 
wrong with your projector.
Do not operate if smoke, strange noise or odor comes 
out of your projector. It might cause fi re or electric 
shock. In this case, unplug immediately and contact 
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An 
inadvertent contact may result in an electric shock. 
Except as specifi cally explained in the User Manual do 
not attempt to service this...

EN-6
Preparing your projector
1
23 Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in 
the package. 
Cables
Remote control parts
Remote control
(290P176-10)R6 (size-AA) 
battery (two) 
Others
•  Lens cap (attached to the projector)
• Terminal cover
•  Lamp replacement tray
• CD-ROM
•  Safety Manual/Quick Start up 
Power supply parts
RS-232C cable
(J2552-0114-00) RGB cable for PC 
(J2552-0072-03)
Mini D-SUB
15-pin...

EN-7
Overview
5634
12
910
78
5 4
7
10 6
9
11
8 1
2
3
1 Control area
2 Speaker
3  Air outlet grille
4 Lens
5  Remote control sensor (front)
6  Air inlet grille
7  Remote control sensor (rear)
8 Lamp cover
9 Terminal panel
10 Air outlet grille
Caution:
Do not replace the lamp immediately after 
using the projector because the lamp would 
be extremely hot and it may cause burns.
Control area
1 POWER indicator
2 COMPUTER/DVI-D/W button
3 ZOOM/FOCUS button
4 STATUS indicator
5 POWER button
6 AUTO POSITION/S...

EN-8
1
Preparing your projector (continued)
Bottom side
1 Adjustment feet
31
COMPUTERHDMI VIDEO KEYSTONE AUTO POSITION
DVI-D(HDCP) S-VIDEO
FREEZE MAGNIFY
AV MUTE
PA G E  U P HOME
PA G E  D O W N END
1
2
P in P
VOLUME
4
7
8
10
11
12
1318
19
22
23
24
25
26
27
28 6
9
14
155
17
16
29
30CE ASPECT
MENUENTER
ZOOM/FOCUS LENS SHIFTLASER21 20
R-CLICK
1
23
Remote control1 Laser aperture
2 Transmission window
3  Wired remote control jack
4 Indicator
5 HDMI button
6 POWER button
7  COMPUTER 1, 2 buttons
8 ZOOM/FOCUS...

EN-9
Using the remote control
30° 30°
30° 30°
20°
10°20°
10°
20° 20°
Operational range of the remote control
•  Keep the remote control photo-sensor out of direct 
sunlight or fl uorescent lamp light.
•  Keep the remote control photo-sensor at least 2 m 
(6 feet) away from fl uorescent lamps. Otherwise, the 
remote control may malfunction.
•  If there is an inverter-operated fl uorescent lamp near 
the remote control, the remote control operation may 
become unstable.
•  When you use the remote control too...

EN-10
Setting up your projector
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the 
projection angle of the projector. (See page 11.)
•  Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of 
the screen center. 
•  Do not install the screen where it is exposed to direct sunlight or lighting. Light directly refl ecting on the screen 
makes the projected images...