Mitsubishi X100 Projector User Manual

21 Projector + AV equipment
Make sure that your equipment is turned off before connection.
Important:
S-video signals take priority over video signals. If you input both S-video signals and normal video
signals at the same time, the normal video input automatically shuts off.
to audio
outputto video
output to S-video
output to audio
outputto video
output to S-video
output
UHF
antennaVHF
antenna Connect either one of these.
Connect either one of these.
VCR, othersDVD player, others
to audio input 1
to...

22
To operate projector power ON
POWER
red
green
red LAMP
-
green
- when light source lamp is on
when light source lamp does not light up
indicator
condition
stand-by
LAMP
SOURCEFREEZE
/CAPTURE
TEMP
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator
lights up red.
2. Turn on the equipment connected to the projector.
3. Turn the projector on by pressing the POWER button.  The light source lamp starts warming up,
eventually turn on. Numbers 1~10 correspond to the...

23
4.  Select the desired external input source by using the SOURCE button.
The source changes in the sequence shown below:
•The projector automatically selects the appropriate signal system. When the source is selected to
RGB1 or RGB2 and the image is not in the right place, set to display as blightest signal as pos-
sible, then press the AUTO button. If the image is still not in the right place, refer to USER
PRESETS on page 32.
•The projector automatically convert the image into full screen size. By...

24
Menu operation
Several settings can be adjusted using Menu. There are 5 modes. You can also make adjustments
using PCGC (personal computer graphic controller). See pages 42 ~ 44 for details.
MENU layers
• If the menu operation is not working, simultaneously press the MENU and POWER button.
MAIN MENU
POINTER
CURSOR
  SELECT
  SIZE
  DEFAULT POS
CURSOR TRAILS  COLOR
  WIDTH
NORMAL
CONTRAST
BRIGHTNESS
TINT
COLOR
GAMMA CORRECTION
ENHANCED
IMAGE REVERSE
ZOOM/SUPER
SOURCE ID
BLUE BACK
TEST PATTERN
AUDIO...

25
CONTRAST BRIGHTNESS TINT COLORGAMMA CORRECTION
R / G / B
RESET
  0
R / G / BUSER
  0  0  0
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
CONTRAST BRIGHTNESS
R / G / B
  0
R / G / B
  0
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
CONTRAST BRIGHTNESS
R / G / B
  0
R / G / B
-15
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
CONTRAST BRIGHTNESS
R / G / B
  0
R / G / B
  0
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
Basic operation
EXAMPLE: Brightness adjustment
2, 42, 4
1, 51, 5
LAMP
SOURCEMENU...

26 NORMAL menu
The following adjustments to the projected image can be done in this menu.
CONTRAST BRIGHTNESS TINT COLORGAMMA CORRECTION
R / G / B
RESET
  0
R / G / BUSER
  0  0  0
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
Adjusts the picture contrast. The contrast becomes higher as the number increases.
If you wish to select the color, select R/G/B and
press the ENTER button. (The R/G/B setting
menu will be displayed.) To exit the R/G/B setting
menu, select RETURN and press the ENTER
button. To...

27 GAMMA CORRECTION menu
The proportion of the brightness of input signals to that of output signals can be corrected effectively
by adjusting GAMMA.
1. Select  GAMMA CORRECTION of NORMAL menu and then press the ENTER button. (The
GAMMA CORRECTION menu appears on-screen display.)
Horizontal axis: brightness of the input signals
Vertical axis: brightness of the output signals
Inclination: GAMMA
2. Press the ª or º buttons on the control panel (or { or } buttons on the remote control) to
select MASTER.
3....

28 ENHANCED menu
The following adjustments for enhanced items can be done in this menu.
HELPIMAGE
REVERSEKEYSTONE
OFFON OFF
1
2
3
4
5
MIRROR
INVERT INVERT
MIRROR
SOURCE IDBLUE BACKTEST
PATTERNZOOM/
SUPER
ZOOM
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUITRESETOFFON
OFF
SUPER
IMPOSE
0˚
3˚
6˚
9˚
12˚
15˚
Use to reverse or invert the projected image. MIRROR is usedfor rear projection.
INVERT is effective when the projector is ceiling-mounted.
Adjusts keystone correction of the image. If the image becomes keystone...

29
VIDEO11
2
3
4
51
2
3
SOURCE FRAME
POSFRAME
SIZESUPER
IMPOSE
RETURN
RESET
VIDEO2
RGB1
RGB2
PC1
PC2
Selects the desired input source of the sub-image. Select the desired input source
by pressing the ª or º buttons on the control panel (or { or } buttons on the
remote control).
Selects the desired position of the sub-image. Select the desired position by pressing
the ª or º buttons on the control panel (or { or } buttons on the remote con-
trol).
Selects the desired size of the sub-image. Select the...

30 POINTER menu
The following adjustments to the cursor and cursor trails can be done in this menu.
SELECT CURSORCURSOR TRAILS
SIZE DEFAULT POS
H-POS
V-POS  50
 50COLOR WIDTH
RESET
1
2
3
4
51
2
3
4
5
6
71
2
3
4
5
6 1
2
3
HELP
NORMAL
ENHANCED
POINTER
AUDIO
OPTION
QUIT
Selects the desired color of the cursor. Select the desired color by pressing the ª or
º buttons on the control panel (or { or } buttons on the remote control).
Selects the desired size of the cursor. Select the desired shape by pressing the...