Mitsubishi Wd720u Projector User Manual
Have a look at the manual Mitsubishi Wd720u Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-51 This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. Spare lamp for XD700U/WD720U: VLT-XD700LP Caution:• Do not remove the lamp immediately after using the projector. You may get burned because the lamp is very hot after use.• Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for lamp to cool down. Unplug the power cord from wall outlet and wait one hour for the lamp to cool down completely.• Do not remove the lamp except for replacement. Careless handling can cause injury or fire.• Do not touch the lamp with bare hands or give a shock to the lamp. Attach the lamp properly. Improper handling may cause explosion.• Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or any flammable objects inside because it may cause fire or electric shock. If any objects should fall inside, unplug and contact your dealer.• Install the lamp securely to prevent failure and fire.• If the lamp should break, small glass fragments may fall out through the vents and some may remain inside of the projector or the lamp box. When taking the lamp box out, be sure to turn over the projector and hold the handle of the lamp box to avoid injury due to the glass fragments.• If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes.• When removing the lamp from the ceiling-mounted projector, use the lamp replacement attachment packed with the projector or option lamp to prevent glass fragments from scattering.• Be sure to use the lamp dedicated to this projector, VLT-XD700LP for XD700U/WD720U. Use of other lamps may cause a failure of the projector. A) When the projector is placed on the tableMake sure that the projector is securely held in place. 1. Remove the cover (a) of the screw fixing the lamp cover with a fingernail. If it is difficult to remove it with a fingernail, use a finetipped tool such as flathead screwdriver. (a) 2. Remove the screw (b) and slide the lamp cover (c) for removal. (c) (b) Lamp replacement 3. Loosen the two screws (d) of the lamp unit, and then pull out the lamp unit (f) by the handle (e). (f) (d) (e) Caution:• When replacing the lamp, do not loosen the screws other than two screws (d). It may cause the failure of projector.• Pull the lamp unit out of the projector slowly. If it is pulled out quickly, the lamp may break, scattering glass fragments.• Do not spill liquid on the removed lamp unit or do not place it near any flammable object or where children can reach to prevent injuries or fire. 4. Insert the new lamp unit, and secure it with two screws firmly. 5. Secure the lamp cover with screw (b) back again, and mount the cover (a). Caution:• Make sure that the lamp cover is secured firmly. Otherwise, the POWER indicator flashes red and green, disallowing the projector to be powered on. B) When the projector is mounted to the ceilingWhen removing the lamp unit from the projector mounted to the ceiling, never fail to use the lamp replacement attachment to protect yourself from glass fragments and so on. • Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling. 1. Remove the lamp cover referring to the procedure 1 and 2 of “A) When the projector is placed on the table”. Caution: • When opening the lamp cover to replace the lamp of the ceiling-mounted projector, pay careful attention because glass fragments may exist inside the lamp cover. 2. Loosen the two screws (d) of the lamp unit. (d) Caution:• When replacing the lamp, do not loosen the screws other than two screws (d). It may cause the failure of projector.
EN-52 Lamp replacement (continued) 3. Assemble the lamp replacement attachment by folding two taping portions (g) and two cutout portions (h) along the folding line as the figure. (h) (h)(g) (g) 4. Insert the two cutout portions (h) in the slit of the projector, paste the two taping portions (g) with the tape included in the lamp replacement attachment, and then fix the lamp replacement attachment to the projector. (g) (g) (h) 5. Pull out the lamp unit (f) in the bag by the handle (e). (f) (e) 6. Remove the tape fixing the lamp replacement attachment, and remove the lamp replacement attachment with the lamp unit remaining in the bag. Caution:• Pull the lamp unit out of the projector slowly. If it is pulled out quickly, the lamp may break, scattering glass fragments.• Do not spill liquid on the removed lamp unit or do not place it near any flammable object or where children can reach to prevent injuries or fire. 7. Insert the new lamp unit, and secure it with two screws firmly. 8. Secure the lamp cover with screw (b) back again, and mount the cover (a). Caution:• Make sure that the lamp cover is secured firmly. Otherwise, the POWER indicator flashes red and green, disallowing the projector to be powered on. Reset of the lamp operation timePlug in the power cord, and reset the lamp operation time by keep pressing the , , and POWER buttons on the control panel at the same time. Important:• Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.• Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.• The projector doesn’t turn on if the lamp cover isn’t attached securely.• Be sure to reset the lamp operation time whenever you replace the lamp.• Do not reset the lamp operation time unless you replace the lamp. Caution:• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.• Contact your dealer for a new lamp. Interval of lamp replacementThe recommended interval of lamp replacement is about 5000 hours*1*2 of consecutive use. Such interval differs depending on the operating environment and may be shorter than 5000 hours*1*2.Decrease in luminescence and/or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3750 hours*1, the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator will be lit red only) and the lamp replacement message will appear on the screen for one minute everytime the lamp is turned on. When the lamp has been used for about 4750 hours*1, the replacement message (Lamp Replacement) will appear on the screen for one minute every 25 hours*1 thereafter. When the lamp operation time exceeds 5000hours*1*2, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp operation time is reset.*1: Duration when Lamp Mode of the Installation menu is set to Low. When it is set to Standard, this duration will be shorted.*2: When Lamp Mode is set to Standard, this duration will be shorted to 3000 hours. Important:• Do not open the lamp cover when the projector is set at a ceiling or a high place. Lamp fragments may fall from the inside if the lamp were broken.Please contact your dealer when you need to replace the lamp with a new one. Caution: • This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)
EN-53 Troubleshooting Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer. No image appears on the screen. ProblemSolution Power can not be turned on. • Check whether the indicators are on or off and how they are lightning. POWERSTATUSSolution OffOff• Connect the power cord to the projector. • Plug the power cord into a wall outlet. Steady red Off • If any objects are blocking the intake or exhaust vents, remove them and carry out the following. 1. Unplug the power cord from the wall outlet. 2. Make sure that the projector has cooled off. 3. Plug the power cord into the wall outlet. 4. Press the POWER button. Blinking orange • If any objects are blocking the intake or exhaust vents, remove them. • Don’t expose the exhaust vents to hot air emitted from a heating appliance. Blinking green • After the STATUS indicator stops blinking, press the POWER button.• If you unplug the power cord while the fan is rotating, the lamp may not turn on about 1 minute when you plug the power cord next time. • The lamp can’t turn on again for 1 minute after it goes out. • Press the POWER button several times. Steady red • Replace the lamp. (The lamp is at the end of its life.) Blinking red/green Off• Attach the lamp cover on the top. Steady or Blinking • Unplug the power cord from the wall outlet and contact your dealer. No image appears on the screen. • Cancel the AV mute by pressing the AV MUTE button. • Check that the lens cap is removed. • It may take about 1 minute for the lamp to light up. • The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again. • If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. Press the POWER button to turn back on the POWER indicator. • Check that the intake vent is clean. • Check that the lamp cover is closed. (See page 51 or 52.) • Check that the cables connected to the external devices are not broken. • When an extension cable is being used, replace it with the supplied cable for check. When images are displayed correctly, add an RGB signal amplifier to the extension cable. Power turns off. • This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS indicator brinks orange.) Remove the objects blocking the intake vent and/or exhaust vents and the\ n carry out the following procedure. 1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.) 2. Unplug the power cord from the wall outlet. 3. Wait about 10 minutes. 4. Plug the power cord into the wall outlet. 5. Press the POWER button. • When the STATUS indicator is steady red, it is indicating that the lamp should be replaced. Replace the lamp in this case. • Check that Auto Power Off has been set to Off. • If the lamp has deteriorated, it may go out after a while it illuminates.
EN-54 Troubleshooting (continued) No image appears on the screen. (continued) ProblemSolution The screen for entering the password appears. • Password in the Password menu has been set to On to enable the password lock. Enter the password or contact the person in charge of management of the projector. (See page 48.) “No signal” is displayed. • Turn on the power of the connected device, or check whether there is something wrong with the connected device. • Check whether the external device output signals. (Check this especially when the external device is a notebook computer.) • Check that the cable connected to the external device isn’t defective. • Check that the projector is connected to the external device using the correct terminals. • Check that the connected device is correctly selected as the input source. • When an extension cord is being used, replace it with the supplied cable and check whether images are projected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord. Images are not displayed correctly. ProblemSolution Projected images are shaking. Projected images are displaced. • Check that the cable connected to the external device isn’t intermittent. • Connect the cable’s plug with the external device’s connector firmly. • Press the AUTO POSITION button. • Some computers output out-of-spec signals on rare occasion. Adjust the Signal menu. (See page 25.) • When the input signal is a WXGA video signal, confirm the setting selected in WXGA in the Option menu. • When the input signal is other than a WXGA video signal, select Off in WXGA in the Option menu. Projected images are distorted. • Adjust the projector and the screen so that they are perpendicular to each other. (See page 16.) Projected images are dark. • Adjust Brightness and Contrast in the Picture menu. (See page 31.) • Replace the lamp. (See page 51.) Projected images are blurred. • Adjust the focus. (See page 17.) • Clean the lens. • Press the or button on the remote control to eliminate flicker. • Adjust Tracking and Fine sync in the Signal menu. (See page 25.) • Adjust Brightness and Contrast in the Picture menu. (See page 31.) • Adjust the projector and the screen so that they are perpendicular to each other. (See page 16.) Afterimages persist on the screen. • This phenomenon is improved by keeping projecting an evenly bright image. (Such “image burn-in” phenomenon where afterimages persist on the screen may occur if a stationary image is kept displayed on the screen for a long time.) White dots are seen on projected images. Black dots are seen on projected images. • This phenomenon is normal for a DLP™ projector and is not a malfunction. (A very small number of pixels may visibly or invisibly be persistent all the ti\ me, but they are not a sign of system malfunctions. Over 99.99% of the pixels are effective.) Fine streaks are seen on projected images. • This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a little. • Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player, game console or computer you use. In such a case, you can reduce such streak noise by enabling the LPF.
EN-55 Troubleshooting (continued) Images are not displayed correctly. (continued) ProblemSolution Projected images become wavy. • Connect the plugs of the cables to external devices securely. • Keep the projector away from equipment generating interfering radio waves. • When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal. This isn’t a product malfunction. In this case, readjust the keystone so that the amount of keystone correction is as small as possible. Hue is not appropriate. • Check that the cables connected to the external devices are not broken. Tint in projected images is incorrect. • Check that Computer Input in the Signal menu is correctly set. (See page 25.) • Check that the cable connected to the external device isn’t broken. Different color tint.• When comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a\ malfunction. • When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction. Only the motion areas in the images supplied from the computer aren’t displayed. • This is caused by the computer being used. Contact the manufacturer of your computer. Projected images are obscured. • Match the output resolution of your computer with the resolution of the projector. For the method to change the output resolution of the computer, contact the manufacturer of your computer. (See page 60.) • Some images and texts appear obscured during the keystone adjustment. In such cases, use the projector without applying the keystone adjustment. (See page 16.) Projected images are flickering. • After the POWER button or ON button on the remote has been pressed, or the Lamp Mode setting has changed, images may be flickering until the lamp ligh\ ts stably. This is an expected behavior. • When selecting the input signal, Auto Position, and Image, the projected image may be flickering temporarily. This is not a product malfunction. Projector images are twitching. • Projector may be vibrating. Set Auto Keystone to Off or lower the VOLUME button of the Remote control. Others ProblemSolution The exhaust vents emit warm air. • This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction. No audio is output.• Check that the volume isn’t set to low. • Check the Audio Input setting. • When the external device is connected with an HDMI cable, set the audio output of the device to PCM output. The menu can’t be used. • The microcomputers inside the projector may be wrongly operating because of noise. Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again. “Temperature!!” is displayed. • This indication appears when the ambient temperature rises high. When the ambient temperature stays high, the lamp goes out. Eliminate any causes of the rise in the ambient temperature. • This indication appears when the intake or exhaust vents are blocked. When they are kept blocked, the lamp goes out. Remove the objects blocking the intake or exhaust vents. The mark appears. • This mark appears when ineffective operation is carried out. This isn’t a product malfunction. The remote control doesn’t function easily or at all. • Check that the batteries are loaded in the remote control or the batteries are not weak. (See page 8.) • Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 8.) • Use the remote control within its operation range. (See page 8.) • Use the remote control at least 10 cm away from the projector.
EN-56 Troubleshooting (continued) Others (continued) ProblemSolution The fans sound during standby. • When Standby Mode of the Efficient Mode menu in the Installation menu is set to LAN, Speaker Out, or Monitor Out, the fans rotate at very low speed during standby after plugging the power cord (with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunction. Abnormal sound is heard. • Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symptom is not a malfunction. If the following problem occurs after the lamp is replaced, check the following first. ProblemSolution The projector does not turn on. • Fit the lamp cover securely. (See page 51 or 52.) • Reset the lamp operating time. (See page 52.) The STATUS indicator blinks. • Reset the lamp operating time. (See page 52.) Maintenance Warning: • Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating. Caution: • Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on the projector. • Ask your dealer for annual cleaning of the inside of the projector. If you continue to use the projector with dust inside, it may result in fire or malfunction. Cleaning of the projector and the vents Use a soft cloth to clean the projector and the vents. When the vents become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth. To protect the surface of the projector from fading or deteriorating: • Do not spray insecticide on or inside the projector. • Do not use benzin or thinner to clean it. • Do not let rubber or plastic materials contact with projector. Cleaning of the lens Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens clean\ ing fluid. The lens surface is fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens w\ ith your fingers. Kensington Lock This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instru\ ctions on how to use it to secure the projector. Please contact Kensington Technology Group below. Kensington Technology Group 2855 Campus Drive San Mateo, CA 94403, U.S.A. Phone: +1- (650)572-2700 Fax: +1- (650)572-9675
EN-57 Indicators This projector has two indicators, each of which shows the operation condition \ of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer. POWER indicator STATUS indicator Normal condition POWERSTATUSCONDITIONNOTE Steady red OffStand-by Blinking greenLamp stand-by for power-offThe power cannot be turned on by pressingthe POWER button. Steady green Blinking greenLamp stand-by for power-onThe power cannot be turned off by pressingthe POWER button. Steady greenThe power is on. (Normal condition) Abnormal condition POWERSTATUSCONDITIONPOSSIBLE SOLUTION Steady greenor Steady red Blinking orange Abnormal temperature• The vents are clogged with dust or dirt.• The room temperature is high. • Clean the vents.• Relocate the projector to a cooler place. Steady redBlinking green The protection circuit is working or the lamp is in an abnormal condition.• Wait until the STATUS indicator goes out, then press the POWER button.• If the above solution is not effective, replace the lamp. Steady greenBlinking green/red The lamp operation time exceeds the time elapsed until the lamp lifetime notice while the power is on. (See page 52.) Replace the lamp.Change with a new lamp if this problem recurs. Steady redBlinking red The lamp operation time exceeds the time elapsed until the lamp lifetime notice while the power is off. (See page 52.) Steady redSteady red The lamp operation time exceeds the time elapsed until the lamp lifetime. (See page 52.) Blinking green/redOff The lamp cover isn’t closed.Close the cover correctly. Blinking green/red Steadyor Blinking Abnormal.Contact your dealer.
EN-58 Specifications TypeDLP™ projector ModelXD700UWD720U Rated power supply100 - 240 V AC, 50/60 Hz Power consumption4.1 A During standby: 0.5W (when Standby Mode is Low) Display Technology0.7-inch single chip Digital Micromirror Device (DMD) Pixels: 1024 x 768 = 786432 pixels 0.65-inch single chip Digital Micromirror Device (DMD) Pixels: 1280 x 800 = 1024000 pixels Colors16770000 colors Projection lensF 2.4-2.8, f = 20.6-30.1 mm Light source lamp280 W Picture size40 - 300 inch (Wide) (aspect ratio 4:3)40–300 inch (Wide) (aspect ratio 16:10) PC compatibilityResolution: 640 x 480 (Expand) - 1024 x 768 (Real) - 1600 x 1200 (Compress) Sync on Green available Resolution: 640 x 480 (Expand) - 1280 x 800 (Real) - 1600 x 1200 (Compress) Sync on Green available Video compatibilityNTSC/NTSC 4.43/PAL (including PAL-M, N)/SECAM/PAL-60 Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p, 1080p) Speaker10 W mono x 1 S-video inputLuminance signal: 1.0 Vp-p 75 Ω (negative sync.) Chroma signal: 0.286 Vp-p 75 Ω (burst signal) Video input1.0 Vp-p 75 Ω (negative sync.) Audio input350 mVrms, 10 kΩ or more Analog RGB inputRGB: 0.7 Vp-p 75 Ω (negative sync.) YPBPR/YCBCR: Y: 1.0 Vp-p (negative sync.) PBPR/CBCR: 0.7 Vp-p HD/CS: TTL level (positive or negative) VD: TTL level (positive or negative) HDMI inputHDMI 19-pin HDMI interface (TMDS single link) (only PCM audio is supported) Control connectorSERIAL terminal (RS-232C), LAN terminal (RJ-45) Outside dimensions345 x 134 x 270 mm (width x height x depth) WeightApprox. 4.1 kg Length of power cord71 inch (1.8 m) Temperature, humidity (performance guaranteed) +41°F (+5°C) - +95°F (+35°C), 30 - 90% • The specifications and outside appearance of the projector are subject to change without prior notice.
EN-59 Connectors COMPUTER/COMPONENT VIDEO IN, MONITOR OUT (mini D-SUB 15-pin) 15 11 6 10 15 HDMI (HDMI 19-pin) 191 2 18 COMPUTER/COMPONENT VIDEO IN Pin No. Spec. 1 R (RED)/CR2G (GREEN)/Y 3 B (BLUE)/CB4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V 10 GND 11 GND 12 DDC Data 13 HD/CS 14 VD 15 DDC Clock MONITOR OUTPin No. Spec. 1 R (RED)/CR2G (GREEN)/Y 3 B (BLUE)/CB4 - 5 GND 6 GND 7 GND 8 GND 9 - 10 GND 11 - 12 - 13 HD/CS 14 VD 15 - Pin No.Spec. 1 TMDS Data 2 + 2 TMDS Data 2 Shield 3 TMDS Data 2 - 4 TMDS Data 1 + 5 TMDS Data1 Shield 6 TMDS Data 1 - 7 TMDS Data 0 + 8 TMDS Data 0 Shield 9 TMDS Data 0 - 10 TMDS Clock + 11 TMDS Clock Shield 12 TMDS Clock - 13 CEC 14 - 15 SCL 16 SDA 17 DDC Ground 18 +5 V Power 19 Hot Plug Detect Dimension drawings (unit: mm) 270 345 134 What’s included in the box AC power cord* for the U.S. J2552-0063-03 for Europe J2552-0247-00 for the U.K. J2552-0065-02 for Australia J2552-0053-00 for South Korea J2552-0247-00 Computer cable J2552-0072-05 Remote control Safety Manual/Quick Start up CD-ROM Battery (2) Lens cap Soft case Lamp replacement attachment * One of power cords for the U.S., Europe, U.K., Australia, and South Korea is provided appropriately. Replacement part (option/not included in the box) Spare lamp: VLT-XD700LP Specifications (continued)
EN-60 Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal modeResolution(H x V) Horizontal frequency (kHz) Vertical frequency (Hz) XD700U(H x V)WD720U(H x V) TV60, 480i (525i) -15.7359.941024 x 7681066 x 800*2 *4TV50, 576i (625i)-15.6350.00 1024 x 7681066 x 800*21080i 60 (1125i 60) -33.7560.00 1024 x 5761280 x 720*2 *31080i 50 (1125i 50) -28.1350.00 1024 x 5761280 x 720*2 *3480p (525p) -31.4759.941024 x 7681066 x 800*2 *3 *4576p (625p)-31.2550.00 1024 x 7681066 x 800*2 *3720p 60 (750p 60)-45.00 60.00 1024 x 5761280 x 720*2 *3 *4720p 50 (750p 50)-37.50 50.00 1024 x 5761280 x 720*2 *31080p 60 (1125p 60)-67.50 60.00 1024 x 5761280 x 720*2 *31080p 50 (1125p 50) -56.2550.00 1024 x 5761280 x 720*2 *3CGA84640 x 40037.8684.131024 x 6401280 x 800CGA85640 x 40037.8685.081024 x 6401280 x 800VGA60640 x 48031.4759.941024 x 7681066 x 800*3 *4VGA72640 x 48037.8672.811024 x 7681066 x 800VGA75640 x 48037.50 75.00 1024 x 7681066 x 800VGA85640 x 48043.2785.011024 x 7681066 x 800SVGA56800 x 60035.1656.251024 x 7681066 x 800SVGA60800 x 60037.8860.321024 x 7681066 x 800*3 *4SVGA72800 x 60048.0872.191024 x 7681066 x 800SVGA75800 x 60046.8875.00 1024 x 7681066 x 800SVGA85800 x 60053.6785.061024 x 7681066 x 800XGA601024 x 76848.3660.00 1024 x 7681066 x 800*3 *4XGA701024 x 76856.4870.071024 x 7681066 x 800XGA751024 x 76860.0275.031024 x 7681066 x 800HP751024 x 76862.9474.921024 x 7681066 x 800XGA851024 x 76868.6885.00 1024 x 7681066 x 800XGA1201024 x 76897.55119.991024 x 7681066 x 800*3 *4SXGA70a1152 x 86463.8570.011024 x 7681066 x 800SXGA75a1152 x 86467.50 75.00 1024 x 7681066 x 800SXGA85a1152 x 86477.4985.061024 x 7681066 x 800WXGA601280 x 76847.7759.871024 x 6141280 x 768WXGA60a1280 x 80049.70 59.811024 x 6401280 x 800*3 *4WXGA60b1360 x 76847.7160.01 1024 x 5781280 x 722WXGA60c1366 x 76847.7159.791024 x 5751280 x 720*1 *2WXGA120a1280 x 800101.56119.911024 x 6401280 x 800*3 *4SXGA60b1280 x 96060.00 60.00 1024 x 7681066 x 800*3SXGA75b1280 x 96075.00 75.00 1024 x 7681066 x 800SXGA85b1280 x 96085.9485.00 1024 x 7681066 x 800SXGA601280 x 102463.9860.02960 x 7681000 x 800*3SXGA751280 x 102479.9875.02960 x 7681000 x 800SXGA851280 x 102491.1585.02960 x 7681000 x 800SUN66a1152 x 90061.8566.00 984 x 7681024 x 800SUN76a1152 x 90071.8176.64984 x 7681024 x 800SUN661280 x 102471.6866.68960 x 7681000 x 800SUN76 1280 x 102481.1376.11960 x 7681000 x 800SGI721280 x 102476.9272.30 960 x 7681000 x 800SGI761280 x 102482.0176.00 960 x 7681000 x 800WXGA+601440 x 90055.9459.891024 x 6401280 x 800*3SXGA+601400 x 105065.3259.981024 x 7681066 x 800*3SXGA+751400 x 105082.2874.871024 x 7681066 x 800UXGA601600 x 120075.00 60.00 1024 x 7681066 x 800*3MAC13640 x 48035.00 66.671024 x 7681066 x 800MAC16832 x 62449.7274.551024 x 7681066 x 800MAC191024 x 76860.2475.021024 x 7681066 x 800 *1: When you input the signals WXGA60, WXGA60a, WXGA60b, or WXGA60c, select the supported image size from WXGA of the Option menu.*2: The MAGNIFY mode is not supported.*3: The HDMI terminal is available for these signals.*4: The signals can be displayed with viewing 3D contents on the projector. If a different signal is inputted, the projector shows no 3D contents even with the 3D option set to On in the Picture menu. 3D image may not appear on the screen depending on the PC performance such as graphics board, memory, or CPU. When 3D image is projected on the screen in 120Hz or using certain type of playback software of PC, the image may not appear on the screen. Important:• Some computers aren’t compatible with the projector.• The projector’s maximum resolution is 1024 x 768 pixels (XD700U) or 1280 x 800 pixels (WD720U). It may not display images of higher resolutions than its maximum resolution correctly.• Images with SYNC on G (Green) signal may jitter.• Images with SYNC on G (Green) signal may be tinged with green.• If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by changing the resolution of your computer.• Set Computer Input in the Signal menu to RGB when inputting the HDTV signal as RGB signal.• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO or S-VIDEO terminal, the signal mode is indicated as TV60 or TV50. When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480i or 576i.