Mitsubishi Wd720u Projector User Manual
Have a look at the manual Mitsubishi Wd720u Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 561 Mitsubishi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EN-21 Menu operation You can make various settings using the displayed menus. Installation Closed CaptionStandby Mode Of f, On Option WXGA Auto KeystoneLanguageTest Pattern Passwor dChange Passwor dPassword Network Config Video Image Signal Information H.Position Hold Set Up 0-999V.Position 0-999Fine sync 0-31Tracking User 0-2800Clamp Width 1-63 Clamp Position 1-255LPFOn, Off Overscan 90-100% Shutter(L) 0-20Shutter(U) 0-20 Shutter(RS) 0-20 On, Off0-2550-2550-255 0-2550-255 Shutter(LS) 0-20 *4 *1 Auto, OffCinema Mode Efficient Mode *4 *4 *4 Begin 0-99End0-99 *1 *2 Computer Input Sync. T ype InputResolutionH.FrequencyV.Fr equency Auto, RGB, YCbCr/YPbPr Auto, Of f, 3.75%, 7.50% Splash Scr eenOriginal, User , OffBack ColorBlue, Black, Image Original, Image UserAV Mute ModeBlack, Image Original, Image UserOff, CC1, CC2, CC3, CC4, T1, T2 Low , LAN, Speaker Out, Monitor Out *3 Video Signal Auto, NTSC, PAL, SECAM, 4.43NTSC, P AL-M, PAL-N, PAL-60Off, Auto, 1280x768, 1280x768RB, 1280x800, 1360x768, 1366x768 *5 *2 English, , Español, Français, Italiano, , \ Deutsch, , Polski, Português, , Svensk a, Indonesia, , Türkçe, Magyar, , Bahasa Malaysia Picture Brightness ±30 Contrast±30LowMidHigh ImageAuto Color ±10Sharpness ±5Tint±10Contrast B ±30 Brightness R ±30Brightness G ±30 Contrast R ±30Contrast G ±30 Brilliant Color™ Dynamic, Natural, DetailGamma Center, Upper , Lower 0-10 Brightness B ±30 ±30 ±30 ±30 GainSaturationHue UserRedGreen 3D Off, On3D Sync Invert Off, On *1 *1 *1 AudioAudio Input V olume 0-21 *1*2 *2 *2 *1*2 IP Addr ess DHCP Default Gateway DHCP FunctionOf f, Onxx-xx-xx-xx-xx-xxMAC Addr ess End IP Addr essStart IP Addr ess IP Config Setup Subnet Mask *2 *2 *2 Cyan Magenta ±10 Off, Onxxxx NormalAspect Ratio Full*8 Color T emp. Auto, Normal, EnhancedInput Level Color Management Standar d, Low Lamp Mode Blue Ye llow 16:9 On OK OK Projector Name xxxxxxxx..., SET Network CertificationNetwork Passwor dOKIP Config Lamp TimeOK OK OK Channel SSID Wir eless Setup Encryption Wireless SettingOK Reset AllOK OK Image Captur eOK *7 Theater Pr esentation Standard Black Board White Board AutoAudio 1 Audio 3Mix Audio 2 Of f, Mirr or, Invert, Mirr or InvertImage ReverseAuto Power On Off, On On , Of f AMX Device DiscoveryNetwork InitializationOKNetwork RestartOK Off , On Auto Power Of fOff, 5Min, 10Min, 15Min, 30Min, 60Min *6 *6 *6 *6 Auto, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11SET , Of f, WEP 128bit(ASCII), WEP 64bit(ASCII), WEP 128bit(HEX), WEP 64bi\ t(HEX), WP A-PSK(ASCII), WP A2-PSK(ASCII), WP A-PSK(HEX), WPA2-PSK(HEX) User Menu PositionUpper Left, Upper Right, Center , Lower Left, Lower Right Cr oss Hatch , White , Black Of f xxxxxxxx..., SET *1: Not available with certain signals.*2: Not available when the input signal is from the VIDEO or S-VIDEO terminal.*3: Available only when the input signal is TV60, TV50, 480i, or 576i.*4: The range that can be specified varies across input signals.*5: Available only when the input signal is from the VIDEO or S-VIDEO terminal.*6: Audio 1, Audio 2, Audio 3, and Mix cannot be selected when the input source is HDMI input.*7: “” is not displayed and is not available in WD720U.*8: This function is not available in WD720U.
EN-22 How to set the menus 1. Press the MENU button. • The Main Menu appears on the screen. Confirm Exit SelectMENU Main Menu opt. R G BR G B Pictur e Video Image Signal Audio Installation Option Network Cong Information The item being selected is displayed in r ed letters on a blue backgr ound. 2. Press the or button to select a menu to use. Confirm Exit SelectMENU Main Menu opt. R G BR G B Pictur e Video Image Signal Audio Installation Option Network Cong Information 3. Press the ENTER button (or button). • The selected menu is displayed. Off Installation AdjustMENUExit Select Ef cient Mode Image Reverse Auto Power On Auto Keystone T est Patter n Language Reset All English Of fOff Menu Position Upper LeftOK Cr oss Hatch OK 4. Press the or button to select an item to adjust. Off Installation AdjustMENUExit Select Ef cient Mode Image Reverse Auto Power On Auto Keystone T est Patter n Language Reset All English Of fOff Menu Position Upper LeftOK Cr oss Hatch OK 5. Set the selected item by pressing the or button. Off Installation AdjustMENUExit Select Ef cient Mode Image Reverse Auto Power On Auto Keystone T est Patter n Language English Of fOff Menu Position Lower RightOK Cr oss Hatch Reset AllOK 6. To cancel the menu, press the MENU button several times. Important: • When an item marked with “” is selected, pressing the ENTER button makes its value effective or displays another screen for further setting. • When the MENU button doesn’t function, unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again. • The menus and screens shown in this manual may be different from those of the actual projector. Menu operation (continued)
EN-23 Menu items Set the following items provided in the respective menus. Picture menu Picture AdjustMENUExit Select Image Brightness Contrast Color T emp. Color Management Aspect Ratio Input Level 3D 3D Sync Invert Auto Mid Auto Of f Of f Red Normal 00 ITEMSETTINGFUNCTION ImageAutoAutomatically sets an optimal color balance based on the input signal. Use this setting for most cases. TheaterMakes projected images soft and smooth. Best suited for movies. PresentationMakes projected images bright and crisp. StandardMakes projected images look natural. Black BoardReproduces natural color tones when images are projected directly onto a black board. White BoardReproduces natural color tones when images are projected directly onto a white board. User Use to set Gamma or BrilliantColor™. (See page 32.) Brightness±30Adjusts the brightness of projected images. (See page 31.) Contrast±30Adjusts the contrast of projected images. (See page 31.) Color Temp.4 optionsAdjusts the color temperature. (See page 31.) Color ManagementRed / Green / Blue / Cyan / Yellow / Magenta You can change to any desired color by adjusting each of Gain, Saturation and Hue of six different colors. (See page 32.) Aspect RatioNormalAutomatically sets the aspect ratio in relative to the input signal. Use this setting for most cases. 16:9 Select to expand squeezed (or horizontally compressed) images such as DVD images to 16:9. For XD700U only: Press the ENTER button to select the image display position within the screen from Center, Upper, and Lower. FullSelect this setting when you want to project images in the full screen. Input LevelAuto / Normal / EnhancedFor HDMI signal input: Auto: The proper setting is automatically selected. Normal: Select when grayish black occurs. Enhanced: Select when solid black occurs.(See page 13.) 3D Off / OnSet to On/Off of 3D display. 3D Sync InvertOff / OnSwitches the order of the image for left eye and for right eye. • When Image is switched, projected images may be distorted. Menu operation (continued)
EN-24 Video Image menu Video Image AdjustMENUExit Select Color Sharpness Tint 0 0 0 ITEMSETTINGFUNCTION Color±10Adjusts the color tone of projected images. (See page 31.) You cannot select this setting when the Computer1, Computer2, or HDMI is selected as the input source. Sharpness ±5Adjusts the sharpness of projected images. (See page 31.) Tint±10Adjusts the color tint of projected images. (See page 31.) You can select this setting only when NTSC is selected as the input signal. • You cannot adjust Tint when the TV50 (PAL, SECAM) signal is inputted.• When Computer1, Computer2, or HDMI is selected, Tint does not work. Menu operation (continued)
EN-25 Signal menu Signal AdjustMENUExit Select V. Position Fine sync Computer Input Overscan Hold User On Auto 90% 00T racking 0 H. Position 0 User AdjustMENUExit Select Clamp Width Shutter(U) Shutter(L) Shutter(LS) Shutter(RS) Of f 1LPF 00 00 Clamp Position1 OK ITEMSETTINGFUNCTION H. Position0-999Select this setting to adjust the horizontal position of projected images.V. Position0-999Select this setting to adjust the vertical position of projected images.Fine sync0-31Select this setting to eliminate flickering or blurs, if they appear, when you are viewing projected images.Tracking0-2800Select this setting to eliminate vertical wide stripes, if they appear, when you are viewing projected images.Computer InputAutoAutomatically sets the appropriate setting.RGBSelect this setting when you connect the projector to high definition video equipment having R, G, and B output terminals.YCbCr/YPbPrSelect this setting when you connect the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals.Overscan100%-90%Use this setting to adjust the display area of projected images.HoldOff / On Use this setting to adjust projected images when flagging occurs in the upper area of the screen.UserOK The Signal-User menu is displayed for the following adjustments. Clamp Position1-255Use this setting to correct solid white or solid black that appears in projected images. Clamp Width1-63Use this setting to correct solid black that appears in projected images. LPFOn / OffSelect this setting to enable or disable LPF. Shutter(U)0-20Use this setting to adjust projected images when noise appears in the top part of the image. Shutter(L)0-20Use to adjust the image when noise appears on the bottom part of the image. Shutter(LS)0-20Use this setting to adjust projected images when noise appears in the left half of the image. Shutter(RS)0-20Use this setting to adjust projected images when noise appears in the right half of the image. • Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction.• When you change the value of the horizontal or vertical position drastically, noise may appear.• The adjustable range of the vertical position varies depending on the type of the input signal. The image may be stationary even when the value is changed. These conditions are not a malfunction.• Shutter does not work correctly during keystone adjustment.• When you increase the value of Overscan, noise may appear on the screen. Important:• You can set the Picture, Signal, and Signal-User menus only when the signal is inputted. Menu operation (continued)
EN-26 Audio menu Audio AdjustMENUExit Select V olume Audio Input Auto 16 ITEMSETTINGFUNCTION Audio InputAutoSelects Audio 1 when the input source is Computer1, selects Audio 2 when the input source is Computer2, selects Audio 3 when the input source is Video/S-Video, and selects HDMI when the input source is HDMI. Audio 1 / Audio 2 / Audio 3Selects audio input. Mix Selects mix signal of Audio 1 and Audio 2. You can change the balance of Audio 1/Audio 2 using Mix . Volume 0-21Adjusts the volume of the audio from the speaker. • In Audio Input, HDMI audio is selected when the input source is HDMI input. The audio of Audio 1, Audio 2, Audio 3, and Mix cannot be selected. Menu operation (continued)
EN-27 Installation menu Off Installation AdjustMENUExit Select Ef cient Mode Image Reverse Auto Power On Auto Keystone T est Patter n Language Reset All English Of fOff Menu Position Upper LeftOK Cr oss Hatch Efcient Mode AdjustMENUExit Select Lamp Mode Standar d Auto Power Of f 5MinStandby Mode Low OK ITEMSETTINGFUNCTION Efficient ModeOK Displays the Efficient Mode menu for the following settings. Lamp ModeStandardSelect this option when you want to view images in a well-lit room. LowSelect to moderate the intensity of the lamp. The operating sound is reduced and the lamp lifetime becomes longer.• When this mode is switched, projected images may flicker.• If this mode is frequently switched, the lamp may be deteriorated. Standby ModeLowSelect this option when you don’t use the LAN control, speaker output and monitor output during power standby. This option disables them and reduces the power consumption during the power standby. LANSelect this option when you control the projector via the LAN during power standby. Speaker OutSelect this option when you want to output audio from the speaker during power standby. Monitor OutSelect this option when you want to output video signal from the MONITOR OUT terminal in addition to the audio from the speaker during power standby. Auto Power OffOff / 5-60 MinSelects a desired timer setting until the projector enters the standby mode when there is no signal input from the source. Menu Position5 optionsUse this setting to change the position of the menu on the screen. Image ReverseOffSelect this setting when you want to view images from the front with the projector set on the floor. MirrorSelect this setting when you want to view images from behind the screen with the projector set on the floor. InvertSelect this setting when you want to view images from behind the screen with the projector set at the ceiling. Mirror InvertSelect this setting when you want to view images from the front with the projector set at the ceiling. Auto Power OnOff / OnWhen this mode is set to On, the lamp is automatically lit when the power cord is plugged in the wall outlet. Select On when you set the projector at the ceiling.• When the lamp is off, the projector is in standby. Use the remote control to turn on the lamp. Auto KeystoneOff / OnSelect Auto Keystone function. Test PatternCross Hatch Select to show the test cross hatch pattern. White Select to show the maximum brightness image. Black Select to show the minimum brightness image. Language18 languagesSelects a desired language for the menu. Reset AllOK Resets all menu settings except for Password and Language to the default. • You can display the Efficient Mode menu also by pressing the EFFICIENT MODE button.• Regardless of the setting of Lamp Mode in the Installation menu, the Standard lamp mode is activated by default whenever the projector is turned on. The Lamp Mode is set to either Standard or Low depending on the setting last selected, and you cannot switch the Lamp Mode in about one minute after the lamp is on.• When the Standby Mode is set to Speaker Out or Monitor Out, the audio selected with Audio Input in the Audio menu is output during standby mode. However, no audio is output when the last selected input was HDMI.• During standby mode, you cannot change the audio input and the volume from the speaker.• When Standby Mode is set to LAN, Speaker Out, or Monitor Out, the fans rotate at very low speed during standby after plugging the power cord (with 5 second high speed rotation at the beginning) and after turning off the lamp. This is to cool down the projector operating various functions during standby and is not a malfunct\ ion. When Standby Mode is set to Low, the fans stop during standby.• To cancel the test pattern, press any button. Menu operation (continued)
EN-28 Option menu Option AdjustMENUExit Select Passwor d WXGA Set Up Image Captur e Splash Scr een Back Color AV Mute Mode Of f Original Blue BlackOf f Auto Video Signal AutoCinema ModeAuto Closed CaptionOK OK ITEMSETTINGFUNCTION PasswordOK Use this setting to activate or deactivate the password lock. Cinema ModeAuto / OffSelect Auto to automatically activate the film mode when the input video signal is a video signal from a film. Video Signal8 optionsSelect Auto to automatically set the appropriate video format in relative to the input signal. If projected images aren’t displayed correctly, select a desired video format manually. WXGAOff / Auto / 1280 x 768 / 1280 x 768RB / 1280 x 800 / 1360 x 768 / 1366 x 768 Select the appropriate format when the input signal is a WXGA video signal and the Auto mode does not display images properly.Select Off when the input signal is other than a WXGA video signal. Set UpAutoSelect this setting to automatically change the Set Up mode. OffSelect this setting to lower the density of black. Use this setting when images are dark. 3.75% / 7.50%Select this setting to increase the density of black.• When 7.50% is set, the brightness is decreased by the setup cancel function for the U.S. Image CaptureOK Use to capture the screen for the splash screen. (See page 47.) Splash ScreenOriginalDisplays the original image for the splash screen when the projector is powered on. UserDisplays the image captured for the splash screen when the projector is powered on. OffDisplays no splash screen when the projector is powered on. Back ColorBlue / BlackDisplays blue or black background while no signal is inputted. Image OriginalDisplays the original image for the splash screen while no signal is inputted. Image UserDisplays the image captured for the splash screen while no signal is inputted. AV Mute ModeBlackDisplays black background when the AV MUTE button is pressed. Image OriginalDisplays the original image for the splash screen when the AV MUTE button is pressed. Image UserDisplays the image captured for the splash screen when the AV MUTE button is pressed. Closed CaptionOffDoes not display captions. CC1 / CC2 / CC3 / CC4 / T1 / T2Displays captions. • You can select Cinema Mode only when the input signal is a TV60, TV50, 480i, or 576i video signal.• Captions are not displayed while information about the menu, volume setting, or input signal selection is being displayed on the screen.• The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in North America. Menu operation (continued)
EN-29 Network Config menu Network Cong AdjustMENUExit Select Pr ojector Name Network Certication Network Passwor d IP Cong Wir eless Setting AMX Device Discovery Network Initialization Network Restart OK SET OK OKOK OK Wir eless Setting AdjustMENUExit Select SSID Channel Encryption Wir eless Setup OK Auto Of f MENU IP Cong Adjust Exit Select DHCP IP Addr ess Subnet Mask Default Gateway MAC Addr ess DHCP Function Start IP Addr ess End IP Addr ess IP Cong Setup On OK xx-xx-xx-xx-xx-xx Of f 169- - -255 169 254- - -255 254 0- - -0 0220 0 169 - -169 254 --254 0 --254 221 2541 On Of f SET ITEMSETTINGFUNCTION Projector Namexxxxxxxx...Displays Projector Name. Displays Projector Name in blank when Projector Name is not set. SET Set Projector Name. Enter up to 15 character alphabets (capital/small), numeric characters, or marks. Network CertificationOn / Off Select whether to enable the network certification or not. Select On for normal use. Network PasswordOK Set the password for PJLink certification. IP ConfigOK Select this setting for IP Configuration. (See page 35.) DHCPOn / Off Use this setting when you obtain IP Config automatically by DHCP server. IP Addressxxx-xxx-xxx-xxxDisplays IP Address. Subnet Maskxxx-xxx-xxx-xxxDisplays Subnet Mask. Default Gatewayxxx-xxx-xxx-xxxDisplays Default Gateway. MAC Addressxx-xx-xx-xx-xx-xxDisplays MAC Address. DHCP FunctionOn / Off Use this setting when the projector behaves as a DHCP server. Start IP Addressxxx-xxx-xxx-xxxDisplays Start IP Address. However, Start IP Address is not set as factory default, and cannot be displayed. End IP Addressxxx-xxx-xxx-xxxDisplays End IP Address. However, End IP Address is not set as factory default, and cannot be displayed. IP Config SetupOK Set the IP configuration. Wireless SettingOK Select this setting for wireless configuration. SSIDxxxxxxxx...Displays SSID. SET Set SSID. Enter up to 32 characters (alphabets or numeric characters). ChannelAuto / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11Select the wireless channel. EncryptionSET / Off / WEP 128bit(ASCII) / WEP 64bit(ASCII) / WEP 128bit(HEX) / WEP 64bit(HEX) / WPA-PSK(ASCII) / WPA2-PSK(ASCII) / WPA-PSK(HEX) / WPA2-PSK(HEX) Select the wireless encrypted communication. Wireless SetupOK Set the wireless configuration. AMX Device DiscoveryOff / On Use this setting when using an AMX controller. Network InitializationOK Initializes network setting. Network RestartOK Restarts network function. Menu operation (continued)
EN-30 Information menu Information MENUExit Lamp Time H. Fr equency V. Fr equency Sync. T ype 2000H 60.00 kHz 60.00 Hz 3Wir e Resolution 1024x768 Input Computer1 ITEMDESCRIPTION Lamp TimeThis menu shows a lamp operating time (hour) calculated assuming that \ Lamp Mode is Low. • When the Lamp Mode is Standard, this menu shows a longer lamp operating time than the actual time. (See page 52 for the interval of lamp replacement.) InputIndicates the name of the terminal to which the currently projected video signal is being inputted. ResolutionIndicates the resolution of the currently projected video signal. H. Frequency Indicates the horizontal frequency of the currently projected video signal. V. FrequencyIndicates the vertical frequency of the currently projected video signal. Sync. TypeIndicates the type of the sync signal for the currently projected video signal. Menu operation (continued)