Mitsubishi Wd3300u Projector User Manual

							EN-11
Setting up your projector (continued)
Adjusting the position of the projected image
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1. Press the LENS SHIFT button.
•	The LENS SHIFT menu appears at the center of the screen.
2. Press the , ,  or  button to move the image position.
•	When the  button is pressed, the image moves down.
•	When the  button is pressed, the image moves up.
•	When the  button is pressed, the image moves to the right.
•	When the  button is pressed, the image moves to the left.
•	 When	the	ENTER	button	is	pressed	while	the	LENS	SHIFT	menu	is	displayed,	the	shift	mode	can	be	switched	
between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the , ,  or  button, 
and it shifts in a small amount when STEP is selected.
•	 When	the	LENS	SHIFT	menu	is	displayed	while	no	video	signal	is	input	to	the	projector,	a	crosshatch	appears	on	
the entire screen.
•	 Be	careful	not	to	be	caught	in	the	opening	in	the	lens	while	the	lens	is	moving.
•	 While	the	lens	shift	is	working,	the	screen	may	flicker.
Correcting skewed or distorted image
For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the 
projector using the two adjustment feet on the bottom of the projector.
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet for fine adjustment.
Important:
•	 Don’t	transport	the	projector	with	its	adjustment	feet	extended.	Otherwise	the	
adjustment feet may be damaged. 
When fine streaks are seen on projected images
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus 
a little. (See page 16 or 23 for focus adjustment.) 
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other,  projected images become 
trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments, 
adjust keystone.
To adjust keystone: 
Press the KEYSTONE button on the projector or the 
remote control to display KEYSTONE, and adjust 
the image by pressing the , ,  or  button (or 
VOLUME	+	or	-	button	on	the	remote	control).	
LENS
SHIF T
FASTSELECT :ENTER
Adjustment feet Screen
In the following cases (for front projection):
Press the 
 
(or -) button. Press the 
 
(or	+)	button.
Press the 
 
button. Press the 
 
button.
Important:
•	 For	proper	keystone	adjustment	results,	reset	the	lens	to	the	factory-adjusted	position	using	LENS	SHIFT	RESET	
in the INSTALLATION menu before carrying out keystone adjustment. (See page 30.)
•	When the keystone adjustment is carried out, the adjustment value is ind\
icated. Note that this value doesn’t mean 
a projection angle. 
•	 The	allowable	range	of	the	adjustment	value	in	the	keystone	adjustment	varies	depending	on	the	installation	
conditions. 
•	 When	the	keystone	adjustment	takes	effect,	the	resolution	decreases.	In	addition,	stripes	may	appear	or	straight	
lines may bend in images with complicated patterns. They are not due to product malfunctions. 
•	 When	the	keystone	adjustment	is	performed,	the	displayed	image	may	be	distorted.
•	 Depending	on	the	installation	conditions	of	the	projector	and	the	screen,	a	perfect	rectangular	image	and	the	
proper aspect ratio may not be obtained.
•	 Noise	may	appear	on	the	screen	during	the	keystone	adjustment	because	of	the	type	of	the	video	signal	being	
projected and the setting values of the keystone adjustment. In such cases\
, set the keystone adjustment values in 
the range where the image is displayed without noise. 
•	 When	horizontal	and	vertical	keystone	adjustments	are	performed	in	combination,	the	adjustable	range	becomes	
narrower than in the case when they are performed separately.
•	 In	the	keystone	adjustment	with	the	option	lens,	the	proper	aspect	ratio	may	not	be	obtained. 
						

							EN-12
Setting up your projector (continued)
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount 
kit designed for this projector. Ask a specialist for 
installation. For details, consult your dealer.
•	 The	warranty	on	this	projector	does	not	cover	any	
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•	 When	using	the	projector	mounted	on	the	ceiling,	
set IMAGE REVERSE in the INSTALLATION menu 
to MIRROR INVERT. See page 30.
•	 When	the	projector	is	mounted	on	the	ceiling,	
images may appear darker than those projected in 
the case of tabletop mounting. This isn’t a product 
malfunction.
•	 Ask	your	installation	specialist	to	provide	a	breaker.
 When you do not use the projector, be sure to shut 
down the main power by the breaker.
•	 Do	not	install	the	projector	where	the	exhaust	vents	
are exposed to air emitted by an air conditioning.
 Such installation may cause a breakdown.
•	 Do	not	install	the	projector	near	a	fire	alarm	
because it emits hot air from its exhaust vents.
Rear projection
Ask a specialist for installation. For details, consult 
your dealer.
•	 For	rear	projection,	set	IMAGE	REVERSE	in	the	
INSTALLATION menu to MIRROR. See page 30.
Caution:
•	 Placing	the	projector	directly	on	a	carpet	impairs	
ventilation by the fans, causing damage or failure. 
Put a hard board under the projector to facilitate 
ventilation. 
•	 Place	the	projector	at	least	50	cm	(or	20	inches)	
away from the wall to prevent the air inlet grille and 
the air outlet grilles that emit hot air from being 
blocked.
•	 Do	not	use	the	projector	in	the	following	locations	
and manners, which may cause fire or electric 
shock.
•	 In	a	dusty	or	humid	place.
•	 In	a	sideways	position,	or	with	the	lens	facing	
down.
•	 Near	a	heater.
•	 In 	an 	oily, 	smoky, 	or 	damp 	place 	such 	as 	a 	kitchen.
•	 In	direct	sunlight.
•	 Where	the	temperature	rises	high,	such	as	in	a	
closed car. 
•	 Where	the	temperature	is	lower	than	+41ºF	(or	
+5ºC)	or	higher	than	+95ºF	(or	+35ºC	).
Important:
•	 We	don’t	recommend	using	the	projector	at	an	
altitude of 1500 meters or higher. Use at an altitude 
of 1500 meters or higher may affect the projector’s 
life.  
						

							EN-13
2
1
Viewing computer images
2
1
AUDIO OUTAUDIO IN-1/2
2
1
A. Connecting the projector to a computer
Preparation: 
•	 Make	sure	that	the	power	of	the	projector	and	that	of	the	computer	are	turned	off.	
•	 When
	connecting 	the 	projector 	to 	a 	desktop 	computer, 	disconnect 	the 	RGB 	cable 	that 	is 	connected 	to 	the 	monitor.	
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-1 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER/COMPONENT VIDEO IN-1 terminal of the 
projector. 
2. Connect the other end of the RGB cable to the monitor 
port of the computer.
•	 When	viewing	images	supplied	from	an	analog-connected	
computer, press the COMPUTER 1 button on the remote 
control. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-2 
terminal.)
1. Connect one end of a commercially available BNC cable to 
the COMPUTER/COMPONENT VIDEO IN-2 terminal of the 
projector. 
2. Connect the other end of the BNC cable to the 5 BNC 
terminals of the monitor port of the computer.
•	 When	viewing	images	supplied	from	an	analog-connected	
computer, press the COMPUTER 2 button on the remote 
control. 
For digital connection: 
1. Connect one end of a commercially available DVI cable to 
the COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) 
terminal of the projector. 
2. Connect the other end of the DVI cable to the DVI terminal 
of the computer. 
•	 When	viewing	images	supplied	from	a	digital-connected	
computer, press the DVI-D(HDCP) button on the remote 
control. 
•	Turn on the main power switch of the projector before 
starting the computer. 
For audio connection: 
1. Connect one end of a commercially available PC audio 
cable to the AUDIO IN-1/2 terminal of the projector. 
2. Connect the other end of the PC audio cable to the audio 
output terminal of the computer.
•	 This	projector	uses	stereo	pin	jack	for	its	audio	input.	
Check the type of the audio output terminal of the 
connected computer and prepare a proper cable for 
connection. Some computers don’t have the audio output 
terminal.
•	 Speaker	output	is	mono.
•	 No	audio	is	output	from	the	projector’s	speaker	and	the	
AUDIO OUT terminal during power standby.
COMPUTER/COMPONENT VIDEO IN-1
COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP)
To monitor port
RGB cable
DVI cable (option)
To DVI
Computer
PC audio cable (option)To audio output terminal
2
1
R/PRG/Y
B/PBH/HV V
VH/HVB /P
BG/YR/PR
COMPUTER/COMPONENT VIDEO IN-2
•	 Additional	devices,	such	as	a	conversion	connector	and	an	analog	RGB	output	adapter,	are	required	depending	
on the type of the computer to be connected.
•	 Use	of	a	long	cable	may	decrease	the	quality	of	projected	images.	
•	 Images	may	not	be	projected	correctly,	depending	on	the	type	of	the	connected	computer.	
•	 When	DVI-D	signal	is	input,	some	signal	setting	menus	are	unavailable.	
•	 Also	read	the	instruction	manual	of	the	equipment	to	be	connected.	
•	 Contact	your	dealer	for	details	of	connection.
To monitor port (5 BNC)
Computer
Computer
Computer
BNC cable (option) 
						

							EN-14
Viewing computer images (continued)
1. Plug the attached power cord into the power cord inlet of 
this projector.
2. Plug the other end of the power cord into a power outlet.
•	 The	power	cords	for	use	in	the	U.S.	and	Europe	are	included	with	this	projector.	Use	the	appropriate	one	for	your	
country. 
•	 This	projector	uses	the	power	plug	of	3-pin	grounding	type.	Do	not	take	away	the	grounding	pin	from	the	power	
plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet. \
•	 The	provided	power	cord	for	the	U.S.	is	rated	at	120	V.	Never	connect	this	cord	to	any	outlet	or	power	supply	
using other voltages or frequencies than rated. If you use a power supply using other voltage than\
 rated, prepare 
an appropriate power cord separately.
•	Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.
•	Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to 
the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause 
fire or electric shock. 
•	Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock. 
Caution:
•	Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.
•	Do not plug in or out the power cord with your hand wet. It may cause electric shock.
2
1
Earthing terminal
Power cord (example)
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the 
COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal complies with the DDC2B standard. When a computer 
supporting this standard is connected to this terminal, the computer will automatically load th\
e information from this 
projector and prepare for output of appropriate images. 
•	When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector 
before starting the computer. 
1
Monitor
For monitor connection: 
1.  Connect the RGB cable from the monitor to the MONITOR 
OUT terminal of the projector.
•	 No	video	signal	is	output	from	the	MONITOR	OUT	terminal	
during power standby.
For audio output connection: 
1. Connect one end of a commercially available audio cable 
to the AUDIO OUT terminal of the projector. 
2. Connect the other end (white and red) of the audio cable to 
the audio input terminals (L, R) of the audio equipment.  
•	 When	the	audio	cable	is	connected	to	the	AUDIO	OUT	
terminal, the speaker output is muted.AUDIO OUT2
1
Audio cable (option)
To audio input terminals
MONITOR OUT
RGB cable
B. Plugging the power cord
•	 In	order	to	ensure	the	safety	in	case	of	trouble	with	the	projector,	use	an	electrical	outlet	having	an	earth	leakage	
breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it.  
						

							EN-15
C. Installing the terminal cover
This projector includes a terminal cover. If necessary, install the terminal cover to the projector.
1. Fit two hooks of the terminal cover into the projector.
2. Tighten the attachment screws (a) firmly.
Important:
•	Don’t carry the projector by the terminal cover. 
(a)
Viewing computer images (continued) 
						

							EN-16
Viewing computer images (continued)
D. Projecting images
Preparation:
•	 Remove	the	lens	cap.
POWER buttonCOMPUTER/DVI-D button COMPUTER 1, 2 buttons
LENS SHIFT buttonPOWER button
ZOOM/FOCUS button LENS SHIFT button
Main power switch
ZOOM/FOCUS buttonDVI-D(HDCP) 
button
POWER indicator
STATUS indicator
ENTER button
, , ,  buttons ENTER button
, , ,  
buttons
1. 
Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•	 If	the	projector	was	turned	off	before	the	lamp	was	cooled	down	sufficiently	last	time,	the	fan	may	start	rotating	
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2. Turn on the power of the connected computer. 
3. Press the POWER button.
•	 It	may	take	about	1	minute	for	the	lamp	to	light	up.	
•	 The	lamp	fails	to	light	up	on	rare	occasions.	In	such	a	case,	wait	for	a	few	minutes	and	then	try	again.
•	 Do	not	cover	the	lens	with	the	lens	cap	while	the	lamp	is	on.	Do	not	strip	off	the	aluminium	sheet	inside	the	
lens cap. 
•	 After	the	POWER	button	is	pressed,	the	image	may	flicker	before	the	lamp	becomes	stable.	This	is	not	a	
product malfunction. 
•	 The	lamp	operation	becomes	stable	in	1	minute	after	the	power	is	turned	on	and	then	the	lamp	mode	selected	
in the menu is activated. During the activation, displayed images may be\
 disturbed.
•	 The	projector	starts	warming	up	when	the	POWER	button	is	pressed.	During	the	warm-up	process,	images	
may appear dark and no commands are accepted.
•	 By	blinking	red,	the	STATUS	indicator	indicates	that	the	lamp	should	be	replaced	soon.	Replace	the	lamp	when	
the STATUS indicator blinks red. (See page 41.) 
4. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
5. Adjust with the  or  button to get a fine picture. 
•	 When	the	ENTER	button	is	pressed	while	the	ZOOM/FOCUS	menu	is	displayed,	the	adjustment	mode	is	
switched between FAST and STEP. When FAST is selected, the speed of focus controlled by the  or  button 
becomes fast, and it becomes slow when STEP is selected.
6. Select an input source. 
•	 Press	the	COMPUTER/DVI-D	button	on	the	projector	or	the	COMPUTER	1,	COMPUTER	2	or	DVI-D(HDCP)	
button on the remote control that is corresponding to the terminal in use. 
•	 The	input	source	is	switched	from	COMPUTER	1	to	COMPUTER	2	to	DVI	at	every	press	of	the	COMPUTER/
DVI-D button on the projector. 
•	 The	projector	automatically	selects	the	appropriate	signal	format.	The	selected	signal	format	is	displayed	on	
the screen.
•	 You	cannot	change	the	input	source	while	the	menu	is	being	displayed.
•	 Though	it	may	take	some	time	before	an	image	is	displayed	on	the	screen	depending	on	the	type	of	the	input	
signal, such symptom is not a malfunction. 
•	 Images	may	not	be	projected	in	the	correct	position,	depending	on	the	type	of	the	input	signal.	In	such	a	case,	
press the AUTO POSITION button. (See page 18.)
•	 When	COMPUTER	1	or	COMPUTER	2	is	chosen	as	the	source,	images	supplied	from	the	computer	may	
flicker. Press the  or  button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specified sizes. 
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.) 
•	When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 11.) 
						

							EN-17
Viewing computer images (continued)
9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu.
10. Adjust with the  or  button to get an approximate size. 
•	 When	the	ENTER	button	is	pressed	while	the	ZOOM/FOCUS	menu	is	displayed,	the	adjustment	mode	is	
switched between FAST and STEP. When FAST is selected, the speed of zoom controlled by the  or  
button becomes fast, and it becomes slow when STEP is selected.
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of \
the screen.
12.Press the  or  button to adjust the vertical position and  or  button to adjust the horizontal position of the 
displayed image.
•	 When	the	image	is	not	displayed	within	the	screen,	adjust	the	projection	angle.	In	addition,	perform	the	
keystone adjustment, if necessary. (See page 11.)
Repeat steps 4, 5 and 9 to 12, if necessary. 
Important:
•	 Focus,	zoom	and	lens	shift	adjustment	is	possible	in	the	normal	picture	mode	only.
To stop projecting:
13. Press the POWER button. 
•	 A	confirmation	message	is	displayed.
•	 To	cancel	the	procedure,	leave	the	projector	for	a	while	or	press	any	button	except	the	POWER	button.	
14. Press the POWER button again. 
•	 The	lamp	goes	out	and	the	projector	goes	into	a	standby	mode.	In	this	standby	mode,	the	STATUS	indicator	
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to be turned off. 
•	 During	this	period	of	2	minutes	in	the	standby	mode,	the	intake	fan	and	exhaust	fan	rotate	to	cool	the	lamp.	
•	 The	air	outlet	fans	rotate	faster	as	the	temperature	around	the	projector	rises.
•	 Though	the	fans	make	loud	sounds	during	cooling,	such	symptom	is	not	a	malfunction.
16. Turn off the main power switch. 
•	 The	POWER	indicator	will	go	out.	
•	 If	the	main	power	switch	should	be	turned	off	or	the	power	cord	should	be	unplugged	accidentally	while	either	
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up 
immediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light u\
p, replace the lamp. 
•	 Cover	the	lens	with	the	lens	cap	to	protect	it	from	dust.
•	 For	safety’s	sake,	unplug	the	power	cord	from	the	outlet.
•	 When	you	repeat	turning	off	the	main	switch	within	30	minutes	from	the	lamp	illumination,	an	error	may	occur	
in the clock function of this product.
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the 
POWER button. 
•	 Don’t	shut	down	the	projector	while	the	STATUS	indicator	is	blinking	after	the	lamp	lights	up	because	the	lamp’s	
life may be shortened. 
•	 Don’t	turn	the	projector	back	on	right	after	shutting	it	down	because	the	lamp's	life	may	be	shortened.	(Wait	about	
10 minutes before turning the projector back on.) 
•	 Before	shutting	down	the	projector,	be	sure	to	close	the	menu	screen.	If	you	shut	down	the	projector	without	
closing the menu, the setting data of the menu may not be saved. 
•	 If	you	shut	down	the	projector	while	controlling	the	projector	using	the	network	function,	the	application	software	
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM.  
						

							EN-18
AV mute
The video and audio signals are temporarily muted when the AV MUTE button is pressed. To cancel muting, press the 
AV MUTE button again.
•	 It	takes	several	seconds	before	muting	is	completely	canceled.	
•	 If	AV	MUTE	MODE	in	the	INSTALLATION	menu	is	set	to	IMAGE,	the	splash	screen	will	appear	when	the	AV	MUTE	
button is pressed. 
•	 You	can	alter	the	splash	screen	optionally.	See	page	37.	
•	 The	audio	from	the	AUDIO	OUT	terminal	is	also	muted	by	pressing	the	AV	MUTE	button.
AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1. Project a bright image containing as many texts and characters as possible\
. 
2. When the screen saver has been enabled, disable it. 
3. Press the AUTO POSITION button.  
 The projector automatically makes optimum positional settings for the input si\
gnal. 
•	 If	the	projected	image	is	still	displaced	even	after	pressing	the	AUTO	POSITION	button	several	times,	refer	to	
the procedure to adjust computer images. (See pages 35 and 36.)
•	 When	you	carry	out	this	procedure	with	a	dark	image,	the	image	may	be	displaced.	
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (T\
he key to be pressed depends on the type of 
the computer you use.) 
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure 
that their resolutions are the same (see page 50). For the method to change the output resolution of the computer, 
contact the manufacturer of the computer. 
Viewing computer images (continued) 
						

							EN-19
Viewing computer images (continued)
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio \
of width to height of the image). Change the 
setting according to the type of the screen to be used or your preference. 
How to change the settings:
With the remote control:
1. Press the ASPECT button. 
•	 Every	time	the	ASPECT	button	is	pressed,	the	aspect	mode	changes	from	NORMAL	(FULL)	to	NORMAL	(16:9),	
to NORMAL (4:3), to 16:9, to REAL, to FULL, and back to NORMAL (FULL)\
. 
•	 The	following	table	shows	the	image	display	patterns	depending	on	the	settings.	
4:3 signal, 
XGA signal 
(1024 x 768),  etc.
WXGA signal  1280 x 800  (16:10)
WXGA signal  1280 x 768  (16:9.6)
WXGA signal  1360 x 768  (16:9.04)
16:9 signal  and 
WXGA signal  1366 x 768
16:10
NORMAL (FULL)
Input signal
Setting NORMAL (16:9)NORMAL (4:3) 16:9REALFULL
Input video signal is 
displayed at the max 
height (800 pixels) or 
max width (1280 
pixels) of the panel 
while its aspect ratio 
is maintained. Select this setting 
when using a 16:9 
scr
een.  Select this setting 
when using a 4:3 
scr
een. Regar
dless of the type 
of input signal, image 
is displayed at 16:9 
aspect ratio (1280 x 
720 pixels). Select to 
expand squeezed (or 
horizontally 
compr essed) images 
such as DVD images 
to 16:9. Input video signal is 
displayed at its 
original pixel size. 
(When the pixel size is 
lar
ger than the panel 
size, only the center 
part of the image is 
displayed.)  Regar
dless of the type 
of input signal, image 
is displayed at the full 
panel size (1280 x 800 
pixels).
4:3
1066 x 800
16:9.6
1280 x 768
16:9.04
1280 x 720
16:9
1280 x 720
16:10
960 x 720
16:9.6
1200 x 720
16:9.04
1280 x 720
16:9
1280 x 720
4:3
1066 x 800
16:9.6
1066 x 640
16:9.04
1066 x 602
16:9
1066 x 600
16:9
1280 x 720
16:10 16:9
1280 x 720
16:9
16:9
1280 x 720
16:9
1280 x 720
16:9.6
1280 x 768
16:10
1280 x 800
(1360 x 768)
16:10
1280 x 800
(1366 x 768)
16:10 16:10
1280 x 800
16:10
1280 x 800
16:10
1280 x 800
16:10
1280 x 800
4:3
1024 x 768
4:3
16:10
1280 x 800 1152 x 7201066 x 666 1280 x 7201280 x 8001280 x 800
With the QUICK MENU or FEATURE menu:
(See page 26 for menu setting.) 
1. Display the QUICK MENU or FEATURE menu. 
2. Select ASPECT by pressing the  or  button. 
3. Select your desired aspect ratio by pressing the  or  button. 
When 16:9  is selected with the FEATURE menu, you can select whether or not 
to display signals at 16:9 depending on their type using the following p\
rocedures.
4. Press the ENTER button. 
5. Select a setting for the item MODE by pressing the  or  button.
•	ALL SIGNAL:
 All signals are always displayed at 16:9 irrespective of their type. 
•	VIDEO ONLY:
 Signals supplied from video devices only are displayed at 16:9. 
To cancel the menu:
6. Press the MENU button. 
Important:
•	 If	you	change	the	aspect	ratio	to	16:9,	REAL,	or	FULL	while	displaying	images	on	a	4:3	screen	with	the	aspect	
ratio set to NORMAL (4:3), images appear partly off screen. 
•	 In	such	cases	as	when	you	keep	displaying	images	in	the	4:3	mode	for	a	long	time	and	then	change	the	mode	to	
FULL, the masking areas may remain as afterimage around the displayed image. Consult your dealer in this case. 
•	 When	the	input	video	signal	is	interrupted	with	NORMAL	(16:9)	or	NORMAL	(4:3)	selected,	the	image	turns	blue	
and appears partly off screen. In this case, set BACK COLOR in the INSTALLATION menu to BLACK. 
NORMAL (FULL)
ASPECT
LAMP MODEST
ANDARD
QUICK MENU
CONTRAST
BRIGHTNESS0
0
ST ANDARD
COLOR 0
COLOR
COLOR TEMP
.
0
SHARPNESS
AUTO
COLOR
ENHANCER
SELECT
USER MENU
OK
DET AIL MENU
ASPECT – 16:9
ALL SIGNALMODE
FEATURE
opt. 
						

							EN-20
Viewing video images
Connecting to a video player, etc.
1. Connect one end of a commercially available video cable 
to the VIDEO IN terminal of the projector.
2. Connect the other end of the video cable to the video 
output terminal of the video equipment.
3. Connect one end of a commercially available audio cable 
to the audio input terminals (L/MONO, R) of the projector.
4. Connect the other end of the audio cable to the audio 
output terminals (L, R) of the video equipment.
When the video equipment is equipped with the S-video 
output terminal, make the connection as follows: 
1. Connect one end of a commercially available S-video cable 
to the S-VIDEO IN terminal of the projector. 
2. Connect the other end of the S-video cable to the S-video 
output terminal of the video equipment. 
3. Connect one end of a commercially available audio cable 
to the audio input terminals (L/MONO, R) of the projector. 
4. Connect the other end of the audio cable to the audio 
output terminals (L, R) of the video equipment. 
When using the BNC connector:
(For VIDEO input)
•	When the video output terminal of the connected video 
equipment is BNC type, use the VIDEO IN terminal (BNC 
type). 
•	 Select	VIDEO	as	the	input	source.	
•	When using the VIDEO IN terminal (BNC type) and the 
VIDEO IN terminal (RCA type) at the same time, the video 
signal input to the VIDEO IN terminal (RCA type) takes 
priority. 
When using the BNC connector:
(For S-VIDEO input)
•	When the video output terminals of the connected video 
equipment are BNC (Y/C) type, connect Y and C to the S-
VIDEO IN (Y and C) terminals (BNC type) respectively.  
•	 Select	S-VIDEO	as	the	input	source.	
•	When using the S-VIDEO IN (Y and C) terminals (BNC type) 
and the S-VIDEO IN terminal (S type) at the same time, the 
video signal input to the S-VIDEO IN terminal (S type) takes 
priority. 
•	 When	connecting	a	monophonic	video	device,	use	the	white	(L)	terminal	to	connect	the	audio	cable.	(The	same	
audio signal is output from the channels L and R of the AUDIO OUT terminal.) 
•	 Also	read	the	instruction	manual	of	the	equipment	to	be	connected.	
•	 Contact	your	dealer	for	details	of	connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a messa\
ge of “NO SIGNAL” 
may appear on the screen when you change the channel via any channel that is not being received. In such a case, 
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip 
function (that is a function not to display channels that are not being received) enabled. 
A. Connecting the projector to video equipment
Preparation:
• Make sure that the power of the projector and that of the video equipment are turned off.
3 4
1
2
14
2
3To VIDEO IN terminal
To video output terminal
Video player, or the like
To S-VIDEO IN terminal
S-video cable (option)
To S-video output terminal
Video player, or the like
Audio cable(option)
To audio input terminals
To audio output terminals
To audio input terminalsAudio cable (option)
To audio output terminals
To VIDEO IN terminal (BNC)
BNC cable (option)
To video output terminal
Video player, or the like
To S-VIDEO IN (Y and C) terminals (BNC)
BNC cable (option)
To S-video (Y/C) output terminals
Video player, or the like
Video cable(option)