Mitsubishi Wd3300u Projector User Manual

WD3300
This User Manual is important to you.
Please read it before using your projector.
DLP™ PROJECTOR
MODEL
WD3300U
User Manual 

EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert 
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure 
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an...

EN-3
Contents
Important safeguards ........................................................................\
................................................4
Preparing your projector ........................................................................\
............................................6
Using the remote control  ........................................................................\
...........................................9
Setting up your projector...

EN-4
Important safeguards
Please read all these instructions regarding your 
projector and retain them for future reference. Follow 
all warnings and instructions marked on the projector.
1. Read instructions
 All the safety and operating instructions should be 
read before the appliance is operated.
2. Retain instructions
 The safety and operating instructions should be 
retained for future reference.
3. Warnings
 All warnings on the appliance and in the operating 
instructions should be adhered to.
4....

EN-5
Important safeguards (continued)
WARNING:
Unplug immediately if there is something 
wrong with your projector.
Do not operate if smoke, strange noise or odor comes 
out of your projector. It might cause fire or electric 
shock. In this case, unplug immediately and contact 
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An 
inadvertent contact may result in an electric shock. 
Except as specifically explained in the User Manual do 
not attempt to service this...

EN-6
Preparing your projector
1
2
3
Checking accessories
The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in 
the package. 
Cables
Remote control parts
Remote control
(290P176-20) RS-232C cable
(246C598-10)R6 (size-AA) 
battery (two) 
RGB cable for PC  (246C597-10)
Others
• Lens cap (attached to the pr ojector)
•  Terminal cover (750B017-10)
•  Lamp r eplacement tray (857C132-10)
•  CD-ROM (919C165-20)
•  Safety Manual/Quick Start up...

EN-7
Overview
5639410
1278
5 4
7
10 6
9
11
8
1
2
3
1 
Control area
2 Speaker
3 Air outlet grille
4 Lens
5 Remote control sensor (front)
6 Air inlet grille
7 Remote control sensor (rear)
8 Lamp cover
9 Terminal panel
10 Air outlet grille
Caution:
Do not replace the lamp immediately after 
using the projector because the lamp would 
be extremely hot and it may cause burns.
Control area
1 POWER indicator
2 COMPUTER/DVI-D/ button
3 ZOOM/FOCUS button
4 STATUS indicator
5 POWER button
6 AUTO POSITION/...

EN-8
1
Preparating your projector (continued)
Bottom side
1 Adjustment feet
29
COMPUTERHDMIV IDEO
KEYSTONEA
UTO POSITION
DVI-D(HDCP) S-VIDEO
FREEZE
AV  MUTE
PA GE UP
HOME
PAGE DOWN
END
1
2
VOLUME
4
7
8
10
11
12
13 18
19
22
23
24
25
26
27
6
9
14
15 5
17
16 28CE
ASPECT
MENUENTER
ZOOM/FOCUS
LENS SHIFT LASER21 20
R-CLICK
1
2 3
Remote control1 
Laser aperture
2 Transmission window
3 Wired remote control jack
4 Indicator
5 HDMI button
6 POWER button
7 COMPUTER 1, 2 buttons
8 ZOOM/FOCUS button
9 LENS SHIFT...

EN-9
Using the remote control
30°
30°
30°
30°
20°
10° 20°
10°
20°
20°
Operational range of the remote control
•	 Keep	the	remote	control	photo-sensor	out	of	direct	
sunlight or fluorescent lamp light.
•	 Keep	the	remote	control	photo-sensor	at	least	2	m	
(6 feet) away from fluorescent lamps. Otherwise, the 
remote control may malfunction.
•	 If	there	is	an	inverter-operated	fluorescent	lamp	near	
the remote control, the remote control operation may 
become unstable.
•	 When	you	use	the	remote	control	too...

EN-10
Setting up your projector
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the 
projection angle of the projector. (See page 11.)
•	 Install	the	screen	and	projector	so	that	the	projector’s	lens	is	placed	at	the	same	height	and	horizontal	position	of	
the screen center. 
•	 Do	not	install	the	screen	where	it	is	exposed	to	direct	sunlight	or	lighting.	Light	directly	reflecting	on	the	screen	
makes the projected images...