Mitsubishi Wd3300u Projector User Manual

EN-31
FEATURE menu
FEATURE
NORMAL (FULL)
opt.
MENU POSITION
VIDEO SIGNAL?
ASPECT
RESET ALL
English
LANGUAGEAË
OK
SCAR T INPUT
DISPLA Y INPUT
P
ASSWORD
FUNCTION
CINEMA MODE
1.
SETUP AUTO
OFF
AUTO AUTO
ITEMSETTINGFUNCTION
ASPECTNORMAL (FULL)Input video signal is displayed at the max height (800 pixels) or max width (1280 pixels) of the panel while its aspect ratio is maintained. 
NORMAL (16:9)Select this setting when using a 16:9 screen. 
NORMAL (4:3)Select this setting when using a 4:3 screen.
16:9...

EN-32
SIGNAL menu
USER
1
CLAMP WIDTH CLAMP POSITION 1
LPF OFF
SHUTTER(U) 0
SHUTTER(L) 0
VERT
. SYNC AUTO
?
SHUTTER(LS) 0
SHUTTER(RS) 0
SIGNAL
opt.
SIGNAL
VERTICAL 
FREQUENCY
HORIZONT AL 
FREQUENCY 75.04 Hz
HORIZ. PIXELS 1024
60.02 KHz
CANCEL 
opt.
OK
OKEXECUTE
768
VER T. LINES 
RESOLUTION (MEMORIZE)
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT . POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
USER
opt.
OK
OFFHOLD
100%
OVER SCAN 
MEMOR Y CALL AUTO
RESOLUTION
(MEMORIZE     ) 1024 x 768
VHA
U...

EN-33
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 26 for menu setting.) 
1. Display the QUICK MENU or IMAGE menu. 
2. Select CONTRAST or BRIGHTNESS by pressing the  or  button. 
3. Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4. Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the  button is pressed, the...

EN-34
To cancel the menu:
7. Press the MENU button. 
To enable the stored color temperature: 
1. Set COLOR TEMP. to USER in the QUICK MENU or set it to USER  in the IMAGE menu. 
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. White of which 
temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can 
change the color temperature using the following procedures. 
To raise the...

EN-35
Adjusting projected images (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the flowchart below.
Adjustment is completed.
When the size and position of 
the computer image ar
e not correct. 
Pr...

EN-36
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear. ���������������Adjust TRACKING in the SIGNAL menu. 
The projected image flickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to...

EN-37
Setting of the image displayed 
during startup or muting
You can display your desired image as the startup 
screen (or splash screen). Using the menu, you can 
also use such image as a background that is displayed 
while the video is muted or no signal is supplied.
•	 You	can	capture the images from the COMPUTER1, 
COMPUTER2, DVI, and HDMI input sources.
Setting procedure 
1.  Display your desired image.
2.  Display the INSTALLATION menu.
3.  Select IMAGE CAPTURE by pressing the  or  
button....

EN-38
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specified users. The password function has 3 modes 
as follows.
DISPLAY INPUT ..........When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is 
entered. When the password is entered, the startup 
screen will switch to the regular operation...

EN-39
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote 
control. 
Projector + computer with USB connector
USB cable (option)
USB 4-pin (type B) USB 4-pin
(type A)
To USB port
USB
•	 You	can	use the mouse remote control function with a computer supporting USB only. 
•	You cannot control Macintosh computers using the remote control.
•	 When	the	lamp	is	turned	ON,	the	computer	connected	with	the	USB	cable	may	not	work...

EN-40
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network. 
•	 To	supervise	and	control	the	projector,	install	the	software	“Projector-Control	Device	Installer	*”	contained	in	the	
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control 
Utility” contained in the attached CD-ROM. 
 *) Functions•	 Setting	of	the	projector’s	IP	address•	 Setting	of	password,	display...