Mitsubishi Sl1u Projector User Manual

							3
Sending commands Status code from Meaning
from the PC etc. projector
30 30 72 35 34 0D Command as same as MENU button
0 0 r 5 4 

30 30 72 35 34 0D Command received
0 0 r 5 4 
 (Command echo back)
[Example] Display MENU selection bar. (  is for ASCII code)
Buttons name on remoteASCII HEX
+ VOLUME r06 72h 30h 36h
– VOLUME r07 72h 30h 37h
KEYSTONE r43 72h 34h 33h
EXPAND r02 72h 30h 32h
MUTE ra6 72h 61h 36h
{r53 72h 35h 33h
}r2b 72h 32h 62h
$r4f 72h 34h 66h
%r59 72h 35h 39h
MENU r54 72h 35h 34h
ENTER r10 72h 31h 30h
AUTO POSITION r09 72h 30h 39h
STILL ra4 72h 61h 34h
6) Remote commands
Some remote control operations can be done by remote command codes.
7) Reading command diagram
Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.
ASCII HEX
Function Data (Receive) Function Data (Receive)
POWER ON vP 1 76h 50h 31h
POWER OFF vP 0 76h 50h 30h
INPUT COMPUTER vI r176h 49h 72h 31h
INPUT VIDEO vI v1 76h 49h 76h 31h
INPUT S-VIDEO vI v2 76h 49h 76h 32h
Sending commands Status code from Meaning
from the PC etc. projector
30 30 76 49 0D Command to confirm input
0 0 v I 

30 30 76 49 76 31 0D Command (Input is Video)
0 0 v I v 1 
 carrired out
When a personal computer sends the command, data code will not be attached. On the other hand, the projector
which has received a command will attach the recent operating status and then send.
[Example ]  Input  was Video when the operating status of the input terminal was confirmed.
8) Menu setting commands
The menu setting commands execute the menu setting of this projector. If the personal computer doesn’t send
the commands without attaching the data code, the projector which has received the command replays the
setting data as data code.
ITEM ASCII HEX VALUE
CONTRAST P 50h±30±30±30 (R from G+Main data+B from G)
BRIGHTNESS Q 51h±30±30±30 (R from G+Main data+B from G)
sRGB SRGB 53h 52h 47h 42h0 (OFF), 1 (ON)
COLOR MATRIX (MODE)CMT 43h 4Dh 54h1 (VIDEO), 2 (COMPUTER), 3 (USER), 4 (OFF)
COLOR MATRIX (R, G, B)MRGB 4Dh 52h 47h 42h±30±30±30  (R+G+B)
COLOR MATRIX (Y, C, M)MYCM 4Dh 59h 43h 4Dh±30±30±30  (Y+C+M)
COLOR MATRIX (SATURATION)MSAT 4Dh 53h 41h 54h±05
COLOR TEMP. A 41h1 (Standard), 2 (High), 3 (Low), 4 (User)
COLOR T 54h±10
TINT S 53h±10
SHARPNESS R 52h±10
IRIS AI 41h 49h0 (OFF), 1 (1), 2 (2), 3 (3)
KEYSTONE KS 4Bh 53h±00, ±03, ±06, ±09, ±12, ±15
AUTO POWER ON APON 41h 50h 4Fh 4Eh0 (OFF), 1 (ON)
AUTO POWER OFF APOF 41h 50h 4Fh 46h00 (Off) , 05, 10, 15, 30, 60 
						

							4
ITEM ASCII HEX VALUE
SPLASH SCREEN SS 53h 53h0 (OFF),  1 (ON)
BACK COLOR BB 42h 42h 0 (BLACK),  1 (BLUE)
LAMP MODE LM 4Ch 4Dh 0 (STANDARD),  1 (LOW)
IMAGE REVERSE IR 49h 52h 0 (OFF),  1 (Mirror),  2 (Invert),  3 (Mirror invert)
MENU POSITION MP 4Dh 50h 0 (Upper left),  1 (Lower right)
EXPAND MODE EX 45h 58h 1 -  2
AUDIO MODE AU 41h 55h1 (COMPUTER),  2 (VIDEO),  3 (COMPUTER & VIDEO),  4 (MUTE)
VIDEO SIGNAL VS 56h 53h 0 (AUTO),  1 (NTSC),  2 (PAL),  3 (SECAM) ,
4 (4.43NTSC),   5 (PAL-M),  6 (PAL-N),  7 (PAL-60)
ANAMORPHIC SC 53h 43h 0 (OFF),  1 (ON)
LANGUAGE LG 4Ch 47h 0 (
),  1 (English),  2 (Espa ñol),  3 (Deutsch) ,
4 (Fren çais),   5 (Italiano),  6 ()
RESET ALLRSTALL52h 53h 54h 41h 4Ch 4Ch
MEMORY CALL MMC 4Dh 4Dh 43h 0 (AUTO),  1 (USER1),  2 (USER2)
HORIZ. POSITION HP 48h 50h + (increase),  – (decrease)
VERT. POSITION VP 56h 50h + (increase),  – (decrease)
FINE SYNC. FN 46h 4Eh 00 - 39
TRACKING TRK 54h 52h 4Bh + (increase),  – (decrease)
COMPUTER INPUT CIN 43h 49h 4Eh 0 (RGB),  1 (YCBCR/YPBPR)
HOLD HLD 48h 4Ch 44h 0 (AUTO),  1 (ON),  2 (OFF)
HOLD BEGIN HLB 48h 4Ch 42h –01 - –99
HOLD END HLE 48h 4Ch 45h 01 - 99
CLAMP POSITION CLP 43h 4Ch 50h 00 - 63
CLAMP WIDTH CLW 43h 4Ch 57h 01 - 63
HORIZ. PIXELS HPL 48h 50h 4Ch 0000 - 9999
VERT LINES VLN 56h 4Ch 4Eh 0000 - 9999
VERT.SYNC VSC 56h 53h 43h 0 (AUTO),  1 (ON),  2 (OFF)
SHUTTER (U) SHU 53h 48h 55h 000 - 383  (000  - 299  for SL1U)
SHUTTER (L) SHL 53h 48h 4Ch 000 - 383  (000  - 299  for SL1U)
SHUTTER (LS) SHLS 53h 48h 4Ch 53h 000 - 510  (000  - 398  for SL1U)
SHUTTER (RS) SHRS 53h 48h 52h 53h 000 - 510  (000  - 398  for SL1U)
MUTE MUTE 4Dh 55h 54h 45h 0 (MUTE OFF),  1 (MUTE ON)
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer t\
o the table below for HEX code.
ASCII  +   Ð     0  1  2  3  4  5  6  7  8  9
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example 1] Set the AUTO POWER ON to ON. 
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 a\
nd the difference data of B from to -5.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the 
0 0 P + 1 0 + 0 0 - 0 5 
 picture control 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received 
0 0 P + 1 0 + 0 0 - 0 5 
 (Command echo back)
Sending commands Status code from Meaningfrom the PC etc. projector
30 30 41 50 4F 4E 31 0D Command for setting the
0 0 A P O N 1 
 AUTO POWER ON to ON
30 30 41 50 4F 4E 31 0D Command received 
0 0 A P O N 1 
 (Command echo back)
The data code of CONTRAST and BRIGHTNESS is structured by the difference\
 data of R from G, the main data and 
the difference data of B from G.
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands Status code from Meaning from the PC etc. projector
30 30 53 0D Command to confirm
0 0 S 
 setting of TINT
30 30 53 2B 31 30 0D Command (setting of TINT 
0 0 S + 1 0 
 is +10) carried out