Mitsubishi Sl1u Projector User Manual

							´EN – 11
ENGLISH
LS-VIDEO
VIDEO
AUDIO IN VIDEO INMAIN
AC IN
R COMPUTER INRS-232C
COMPUTER OUT
AUDIO OUT
MONITOR OUTPUT
to COMPUTER IN
to  AUDIO INto monitor port
to  COMPUTER 
OUT
to PC audio
output
PC audio cable (option)
When outputting to both a PC monitor and the projector.RGB cable for PC
RGB cable for PC (option)
computer
Projector + Personal computer
Important:
•When you use a long RGB cable instead of the cable provided, the picture quality may be deteriorated.
•Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector.
Please contact your dealer.
•The audio input for this projector is a stereo pin jack.  (Speaker output is mono.)  Please check the available
cable for the audio input terminal of the PC.  Some personal computer may not have the audio output terminal.
•Select AUDIO MODE COMPUTER to hear and to sound for the COMPUTER. (Refer to page 16).
For using Macintosh
•A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
•A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projec-
tor.  Please contact your dealer. 
						

							EN – 12
Adjustment foot
screen
Preparing the projector for operation
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
•Do not look directly into the lens when projector is
“ON”.
•The lens cap is for protecting the lens.  If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
•This projector is equipped with the power cords for
both U.S. and Europe.  Use the appropriate power
cord for your country.
•A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C  outlet.
•The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
•Use 100-240V AC 50/60Hz correct voltage other-
wise it may lead to fire or electric shock.
•Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid break-
ing the power cord. A broken power cord can cause
fire or electric shock.
•Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
•Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
•Do not plug in or out with wet hands.  It may cause
an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting two foot adjustments on the bottom of the
projector.
1. Lift the projector to the appropriate angle.
2. Press the buttons by the projector’s adjustable front
feet, this will allow the feet to slide out to the ap-
proximate position.
3. Release the foot adjustment buttons to lock the feet
in that position.
4. Rotate the projector feet for fine adjustment.
After using the projector
5. Return the adjustable feet into the projector.
Important:
•The image becomes trapezoid shape when the
screen or project is not level. Use KEYSTONE
button and +, - buttons (or {, } buttons) on the
remote control to adjust, however, the circumfer-
ence of the image may not be focused.
•When the KEYSTONE adjustment is carried out
for a wide image such as a squeezed image, 1080i
image, and 720p image, the size of the displayed
imagewill be smaller.
•Screen on a flat wall with a 90˚ angle to the floor.
•Align projector to produce a full screen display as
illustrated on page 9.
•The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
Adjustment footFront height
adjuster button 
						

							´EN – 13
ENGLISH
To operate projector power ON
•When the lamp indicator is blinking red, the lamp
should be replaced.  Replace the lamp. See pages 21
and 24.
•The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4.  Select the desired external input source by using
the COMPUTER or VIDEO buttons.
•Pressing the VIDEO button repeatedly will select
VIDEO IN and S-VIDEO IN.
•The COMPUTER or VIDEO buttons do not work
when MENU is displayed. At this time, the prohibi-
tion mark (
) appeares on the screen.
•The projector automatically selects the appropriate
signal format. The selected signal format is dis-
played on the screen.
•When selecting the COMPUTER input, the image
may  flicker.  Press the $ or % button to adjust the
image.
•The brightness of the lamp will be STANDARD for
3 minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
5.   Adjust the image size with the zoom ring by turn-
ing it.
6. Adjust the focus with the focus ring by turning it. 1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER but-
ton. The light source lamp starts warming up, even-
tually turning completely on.
•When the light source lamp does not light up,
wait until the LAMP indicator is turned off, then
press the POWER button again.
•If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
ConditionIndicator
LAMPPOWER
Stand-by
-Red
When light source lamp is onGreen
Green
Light source lamp held off temporarilyRed-
Important:
•A darkened image may be seen right after pressing
the POWER button due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
•After the power is turned on or the LAMP MODE is
changed, the screen may flicker before the lamp op-
eration becomes stable. This is due to the charac-
teristics of the lamp, not a failure of the lamp.
LS-VIDEO
VIDEO
AUDIO IN VIDEO INMAIN
AC IN
R COMPUTER INRS-232C
COMPUTER OUT
TEMP
LAMPVOLUMESOURCE
COMPUTER
VIDEO
AUTO 
POSITION
MENUENTER
MUTE
2  •  9
MUTE button
3 • 7 • 8
4
AUTO POSITION
button
3 • 7 • 8 4MUTE button
AUTO POSITION button
STILLENTER MENU
COMPUTER
POWERVIDEOV
C
AUTO
POSITIONMUTE
EXPAND 16:9KEYSTONE
VOLUME
wide
zoom ringtele
far near
focus ring 
						

							EN – 14
30
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
•To exit from this mode,  press any button except
POWER,  STILL and VOLUME + and - buttons.
8. Press the POWER button again.
The light source lamp will be turned off.
Pressing the POWER button second time  will shut
off the light source lamp, but the exhaust fan con-
tinues to operate for 60 seconds to cool down the
light source lamp and LCD panels. In this time, the
lamp indicator will be turned off.
9. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
•In cases where the main power switch is acciden-
tally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, follow as shown below.
1. Set screen to the brightest display as possible
(e.g., full-screen display of the “Tr a s h” window).
2. If the screen saver is running, turn off the screen saver.
3. Press the AUTO POSITION button.
•If the image is still not in the right place, adjust
the image position by using the SIGNAL menu.
The sound from the speaker
The sound from the speaker is mono.
•The output sound is selected by changing the
setting of AUDIO MODE in the FEATURE menu.
See page 16 for details.The volume from the speaker
Press the volume + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
•The volume control bar will disappear about 4
seconds after releasing the volume buttons.
•The volume buttons do not work when MENU
selection bar or MENU is displayed.
AV mute
Image and audio are temporarily erased with press-
ing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
ANAMORPHIC mode
When playing DVD discs containing data of
letterboxed image, press the 16:9 button. Exit the
ANAMORPHIC mode, by pressing the 16:9 button
again.
Caution:
•When you have finished using this equipment, wait
60 seconds for the exhaust fans to stop. Then turn off
the main switch and unplug the power cable from the
wall outlet, for safety purposes.
•After the lamp is turned off,  the lamp cannot be
switched on again for 60 seconds as a precaution-
ary measure. If you wish to turn on the projector
again, wait until the indicator is off then press the
POWER button.
•The exhaust fan rotates faster when the tempera-
ture around the projector rises.
•When the temperature around the projector becomes
too high, the sign  “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically . 
						

							EN – 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select the INSTALLA-
TION menu.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
• If the menu operation is not working, press the
RESET button on the terminal board using a suit-
able sharp object, push gently.
• The settings with 
 mark, you should press the
ENTER button after selecting.
Menu operation
IMAGE
XGA60opt.
INSTALLATION
XGA60opt.
IRIS OFF
KEYSTONE
INSTALLATION
XGA60
0˚
opt.
OFF AUTO POWER 
ONOFFAUTO POWER 
OFF
30 min AUTO POWER 
ONOFFAUTO POWER 
OFF
IMAGE CONTRAST± 30BRIGHTNESS± 30sRGB ON, OFFVIDEOCOLOR MATRIX
COLOR± 10TINT± 10SHARPNESS± 10RED± 30
CYAN± 30GREEN± 30YELLOW± 30
BLUE± 30MAGENTASATURATION
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)
(The item can not be selected when 
the source is selected to COMPUTER)± 30
± 5CONTRAST R± 30CONTRAST B± 30BRIGHTNESS R± 30BRIGHTNESS B± 30
EXPAND MODE 1 - 21=Upper left, 2=Lower right
INSTALLATION
IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
IRIS
AUTO POWER ON ON, OFF
ON, OFFAUTO POWER OFF
COMPUTER, VIDEO, COMPUTER VIDEO, MUTE
ON, OFF
FEATURE MENU POSITION
OFF, 5, 10, 15, 30, 60 minSPLASH SCREENBLUE, BLACKBACK COLORSTANDARD, LOWLAMP MODE
VIDEO SIGNALAUDIO MODE
ANAMORPHICAUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60LANGUAGERESET ALL
SIGNALMEMORY CALL AUTO, USER1, USER2HORIZ.POSITION 0 - 999VERT.POSITION 0 - 999FINE SYNC. 0 - 39TRACKING
USER0 - 9999CLAMP POSITION
0 - +63CLAMP WIDTH 1 - 63HORIZ. PIXELS 0 - 9999VERT LINES 0 - 9999
SHUTTER (L)
0 - 299
0 - 398
0 - 398SHUTTER (U)
0 - 299VERT. SYNC
AUTO, ON, OFF
COMPUTER
USER
OFFSTANDARDHIGHLOW
COLOR TEMP.
USER 
MEMORIZE
*3
*3
*4*1
*2
*3
HOLD AUTO
USER1, USER2
DELETEUSER1, USER2
DEFAULTON
OK
BEGIN -1 - -99END 1 - 99
OFF
COMPUTER INPUT
RGB, YCBCR / YPBPR
*3
*3
*3
*3
* 1: The item can not be selected when the sRGB is set to ON.
* 2: The item can not be selected with certain signals.
* 3: Setting range is different with certain signals.
* 4: The item cannot be selected when the source is selected
       to VIDEO or S-VIDEO.
, English, Español, Deutsch, Français, Italiano,
SHUTTER(RS)SHUTTER(LS)
1, 2, 3, OFFKEYSTONE-15˚, -12˚, -9˚, -6˚, -3˚, 0˚, +3˚, +6˚, +9˚, +12˚, +15˚
*4
*4
*4
*4
*4
*4 *4 
						

							EN – 16
FEATURE
XGA60
MENU POSITION1.
EXPAND MODE 1.AA
RESET ALLEnglish
LANGUAGEAË
ANAMORPHIC OFF
VIDEO SIGNAL AUTO?
OK AUDIO MODECOMPUTER
VIDEO
opt.
IMAGE REVERSE
OFF AUTO POWER 
ONOFFAUTO POWER 
OFF
IRIS OFF
KEYSTONE
ON
INSTALLATION
ON
STANDARD
BACK COLOR
OFF BLUE
XGA60
LAMP MODE
SPLASH SCREEN
0˚
opt.
1 IMAGE
CONTRAST.........Adjusts the picture contrast. The contrast becomes higher as the
number increases.
BRIGHTNESS.....Adjusts the image brightness. The image becomes brighter as
the number increases.
sRGB.................... Select ON to display an image emphasizing on the color
reproducibility.
•When sRGB is ON, COLOR MATRIX, can’t be adjusted.
•When sRGB is ON, the image will become darker.
•When COLOR TEMP is set to other than STANDARD
while sRGB is ON, colors won’t be reproduced as per
the standard value of sRGB.
•Though sRGB can be ON while a signal is input from
VIDEO-IN or S-VIDEO IN, reproduced colors won’t be
in accordance with the sRGB standard value.  Use sRGB to suit your color preference.
COLOR MATRIX.........Adjusts the color balance in each color of the image. See page 18.
COLOR TEMP..... Adjusts the color temperature. See page 18.
COLOR................Adjusts the color intensity of the image. (Available only when VIDEO is selected as the source.)
TINT....................Adjusts the color balance of the image. The color balance of the image shifts green as the number
increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the
source.)
•When the TV50 (PAL, SECAM) signal is inputted, TINT can’t be adjusted.
SHARPNESS....... Adjusts the image sharpness. The image sharpness rises as the number increases.
2 INSTALLATION
IRIS...................... Adjusts the sensitivity of the function (IRIS) which
automatically adjusts the brightness and contrast of the image
depending on the degree of the light in the room. When using
this projector in a room where the light and shade varies
slightly, select 1. When using this projector in a normally
lighted room, select 2. When using this projector in a room
where the light and shade varies greatly, select 3.When you
select OFF, IRIS won’t operate.
•When the sensitivity is adjusted in a large amount, the
image may be displayed solid white.  Adjust the
sensitivity depending on the operating environment
and imges to be displayed.
KEYSTONE ......... Corrects keystone distortion. Select an optimum value for
proper display. For normal use, select 0˚.
AUTO POWER ON......Select ON to boot up the projector automatically by turning on an externally connected power switch
such as a breaker even when the main power switch of the projector is off. Use this setting when the
projector is hanging from the ceiling.
•The projector will be in the stand-by mode when the lamp is off.  Use the remote control to turn
on the lamp.
AUTO POWER OFF....Set the time elapsed before the projector enters into the stand-by mode when there is no signal
inputted from the selected source.
SPLASH SCREEN.......Select ON to display the splash screen when the power is turned ON.
BACK COLOR......Use to select the color of the background, blue or black, which will be displayed when there is no signal
inputted from the selected source.
LAMP MODE .......Use to change the brightness of the lamp. When LOW is selected, the image will become darker,
though the power will be saved, operating sound will be reduced.
•The brightness of the lamp will be STANDARD for 3 minutes regardless of the setting of the LAMP
MODE when the lamp turns on.
•When the LAMP MODE is changed, the screen may flicker. This is not a failure of the lamp.
IMAGE REVERSE......Use to reverse or invert the projected image. Select MIRROR in rear projection. Select MIRROR,
INVERT in rear projection with the projector hanging from the ceiling.
3 FEATURE
MENU POSITION.......Use to select the position of the menu on the screen,   (upper
left) or 
 (lower right).
EXPAND MODE .. Select the mode for enlarging screen. See page 20.
AUDIO MODE.....Select COMPUTER to output the sound which is inputted to
the audio input terminal when COMPUTER is selected as the
source. Select VIDEO to output the sound which is inputted to
the audio input terminal when VIDEO is selected as the source.
Select COMPUTER VIDEO mode to always output the sound
which is inputted to the audio input terminal. Select MUTE not
to output the sound at all.
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
0 0
XGA60
COMPUTEROFF
TINT
COLOR TEMP.
SHARPNESS COLOR MATRIX sRGB
opt.
Menu operation (continued) 
						

							EN – 17
ENGLISH
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 0
HORIZ. PIXELS 0
SHUTTER(RS) 0 VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0
SHUTTER(L) 0
SHUTTER(U) 0
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
HOLD AUTO
USERMEMORIZEDELETE DEFAULT
R G BR G B
A
U
XGA60opt.
VIDEO SIGNAL ... When AUTO is selected, the appropriate video format is automatically selected depending on the
input signal. If the image isn’t displayed correctly, select the desired video format manually.
ANAMORPHIC....Select ON when playing DVD discs containing data of letterboxed images.
LANGUAGE........Use to select the language used in the menus. (
 / English / Español / Deutsch / Français /
Italiano / 
)
RESET ALL.........Use to reset the MENU settings (except LANGUAGE).
4 SIGNAL
MEMORY CALL ........Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....The unit adjusts itself automatically when connected to a
DVD player with a component video output (Y, C
B, CR). In
the case ( Y, P
B, PR). In the case the projector is connected to
equipment that includes RGB output terminal, adjust to
RGB mode.
HOLD .................. Adjusts the image when flagging occurs near the top of the
screen.
5 SIGNAL  - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image.  The image size grows
wider as the number increases.  (Adjust to the horizontal
pixels of the input signal for normal setting.)
VERT.LINES ...... Use to adjust the height of the image.  The image size grows
higher as the number increases.  (Adjust to the vertical lines
of the input signal for normal setting.)
VERT.SYNC. ...... U s e  t o  adjust the image when its motion does not run
smoothly.  Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part
of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.
User memory for signal setting
This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1.  Select MEMORIZE 
 in the SIGNAL menu, and press the ENTER button.
2.  Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).
3.  Press the ENTER button.
•Any buttons are ineffective about 3 seconds of recording setting.  Wait for recording to have been completed
before operating the buttons.
Initialite the setting which has been changed (Default)
Select RESET 
 in the SIGNAL menu, and press the ENTER button.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER
2).
Reset the recorded setting
1.  Select DELETE 
 in the SIGNAL menu, and press the ENTER button.
2.  Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3.  Press the ENTER button.
The recorded setting will be reset.
•Any buttons are ineffective about 3 seconds of resetting the recorded setting.  Wait for resetting to have been
completed before operating the buttons. 
						

							EN – 18
Adjusting the image
You can adjust the picture by using the IMAGE menu.
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu.  Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu.  Press the %
button to lighten the image and the $ button to
darken the image.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu.  Press the % button
to increase the amount of red in the image and the $
button to increase the amount of green in the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu.  Press the %
button to make the picture seem sharper and the $
button to make it softer.
Color matrix
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using Color correction
adjustment. Use Color correct adjustment when
enphasizing a specific color, or when only a certain
color balance is not correctly adjusted.
1.  Select COLOR MATRIX in IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired color.
•If you wish to adjust the color intensity of the
image, select SATURATION.
5.  Press the $ or % button to adjust the color balance
of the color.
Picture adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
CONTRAST
IMAGE
0
BRIGHTNESS 0
STANDARD
0
COLOR
0 0
XGA60
COMPUTEROFF
TINT
COLOR TEMP.
SHARPNESS COLOR MATRIX sRGB
opt.
About color temperature
There are different kinds of white color. Color temperature is
a way to show the differences. The white, which temperature
is low, becomes raddish white. When the color temperature is
higher, the white becomes more bluish. This projector sets
this color temperature by changing the numbers of contrast
blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the contrast R
(Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the contrast R
(Red) number high.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
•When using the setting which has been already
prepared, select desired position VIDEO or
COMPUTER in step 2.  When the source is selected
to VIDEO or S-VIDEO, VIDEO will be selected
automatically. When the source is selected to
COMPUTER, COMPUTER will be selected
automatically.
•When not using Color matrix adjustment, select
OFF in step 2.
Color temperature
1.  Select COLOR TEMP in IMAGE menu.
2.  Press the $ or % button to select USER 
.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired item.
5.  Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU but-
ton several times.
COLOR MATRIX
RED 0
0
0 0 0
GREEN
BLUE YELLOW
CYAN
MAGENTA 0
SATURATION0 
						

							EN – 19
ENGLISH
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press the AUTO POSITION
button.  If the images are still not projected correctly,
use the MENU display to adjust the projected im-
ages.
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu.  Press
the % button to move the image to left.  Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu.  Press
the % button to move the image to upward.  Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise appears on right or left side of image :
Adjust SHUTTER (LS), SHUTTER (RS) or  HORIZ.
PIXELS  of the menu in SIGNAL - USER menu.
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
HOLD AUTO
USERMEMORIZEDELETE DEFAULT
R G BR G B
A
U
XGA60opt.
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 0
HORIZ. PIXELS 0
SHUTTER(RS) 0 VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0
SHUTTER(L) 0
SHUTTER(U) 0
Top part of image curves :
Change the setting of HOLD in SIGNAL menu.
Select ON 
, press the ENTER buttun and adjust
BEGIN or END for image which top part is the least
curved.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL -
USER menu.  Select AUTO for normal setting.
curved.  Select AUTO for normal setting.
•Do not change each menu setting in USER
menu for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image). 
						

							EN – 20
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote con-
trol, you can magnify the detailed image of the picture.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active pic-
ture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
REAL screen display
You can view the screen displaying the picture as its
original size (native resolution display).
Setting the Expand mode for REAL screen
display
1. Press the MENU button.
2. Press the $ or % to select the FEATURE menu.
3. Press the ENTER button.
4. Press the  { or } button to select EXPAND MODE.
5. Press the $ or % to set the EXPAND MODE 2.
Native resolution
 display
(EXPAND MODE 1)(EXPAND MODE 2)
Zooming
image
EXPAND MODE 
6. Press the MENU button twice to exit the menu sys-
tem.
Viewing the REAL screen display
1. Press the EXPAND button.
2. Exit the EXPAND mode, by pressing the EXPAND
button again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
•During REAL mode, Press the $ or % buttons
for fine adjustment.
•During REAL mode, the { and } buttons are
not working. At this time, the prohibition mark
(
) appeares on the screen.
•The expanding rate cannot be changed by press-
ing either the + or - button. They are working for
volume adjustment.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will be freezed temporary.
To resume picture activity.
2. Press the STILL button on the remote control
again.