Mitsubishi S290u Projector User Manual

							EN – 11
ENGLISH
Connection
For IBM PC or IBM PC compatibles
to monitor 
port
computer
PC audio 
cable (optional)
RGB cable for PCRGB cable for PC
(optional)
to AUDIO IN
to PC audio 
outputto PC 
monitor
to COMPUTER
 IN
to COMPUTER OUT
When outputting to both a PC monitor and the projector.
For Macintosh
to video portcomputer
MAC adapter for
RGB cable (optional) Monitor Conversion
adapter (optional)Monitor cable
(optional)
to AUDIO IN
to PC audio 
output
to COMPUTER IN
to COMPUTER OUT
123456
ON DIP
PC audio 
cable (optional)
When outputting to both a PC monitor and the projector.
to PC
monitor
RGB cable for PC
Projector + Personal computer
Important:
•Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
•The audio input for a personal computer is a stereo mini jack. There are some personal computers that have
different types of audio outputs or none at all. Please ask your dealer for details.
•A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
•If you use the MAC adapter for RGB cable, set the dip switch to the appropriate position. 
						

							EN – 12
Adjustment foot
screen
Preparing the projector for operation
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
•Do not look directly into the lens when projector is
“ON”.
•The lens cap is for protecting the lens.  If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
•This projector is equipped with the power cords for
both U.S. and Europe.  Use the appropriate power
cord for your country.
•A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C  outlet.
•The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
•Use 100-240V AC 50/60Hz correct voltage other-
wise it may lead to fire or electric shock.
•Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid break-
ing the power cord. A broken power cord can cause
fire or electric shock.
•Do not revise or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is broken.
Caution:
•Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
•Do not plug in or out with wet hands.  It may cause
an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting two foot adjustments on the bottom of the
projector.
1. Lift the projector to the appropriate angle.
2. Press the buttons by the projector’s adjustable front
feet, this will allow the feet to slide out to the ap-
proximate position.
3. Release the foot adjustment buttons to lock the feet
in that position.
4. Rotate the projector feet for fine adjustment.
After using the projector
5. Return the adjustable feet into the projector.
Important:
•Screen on a flat wall with a 90˚ angle to the floor.
•Align projector to produce a full screen display as
illustrated on page 9.
•The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart. 
						

							EN – 13
ENGLISH
To operate projector power ON
•The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4.  Select the desired external input source by using
the COMPUTER or VIDEO button.
•The projector automatically selects the appropriate
signal format. The selected signal format is dis-
played on the screen.
•When selecting the COMPUTER input, the image
may  flicker.  Press the $ or % button to adjust the
image.
•When input signal is jittering, please adjust by $
or % button also connecting with DVD player or
MUSE decoder etc.
•When supplying unstable signal like Still or
Reverse play with VCR, “NO SIGNAL” may
appear on the screen. In this case, you may avoid
this issue by selecting the right color format like
NTSC, PAL in OPTION menu.
5.   Press the ZOOM/FOCUS button to FOCUS. “FO-
CUS” will appear on the display.
6. Adjust with the + or - button to get a fine picture.
7.   Press the ZOOM/FOCUS button to ZOOM. “ZOOM”
will appear on the display.
8. Adjust with the + or - button to get an approximate
size.
•Focus and zoom adjustment  is possible in the normal
picture mode only. In PinP or EXPAND mode, the
adjustment is impossible. 1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
3. Turn the projector on by pressing the POWER but-
ton.
The light source lamp starts warming up, eventu-
ally turning completely on.  In case the light source
lamp does not come on, wait for one minute before
switching power on again.
•If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
conditionindicator
LAMPPOWER
stand-by
-red
when light source lamp is ongreen
green
light source lamp held off temporarilyred-
Important:
•A darkened image may be seen right after pressing
the POWER button due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
•When the lamp indicator is blinking red, the ser-
vice life of the lamp is about to end.  Replace the
lamp. See pages 23 and 26.
ENTER
RIGHT CLICKLASER
COMPUTERVIDEOZOOM/
FOCUS
MUTE
VO LM E
AUTO
POSITION
MENU
P in P EXPAND STILL
L
RAUDIO VIDEO S-VIDEO
MAIN
AC INAUDIO OUT
VIDEO 1 IN VIDEO 2 IN
COMPUTER OUTAUDIO 2 INCOMPUTER 2 INAUDIO 1 INCOMPUTER 1 IN
OI
REMOTE
USBRS-232C
2 , 11
AUTO POSITION 
button
AUTO POSITION 
buttonMUTE 
buttonSTILL button
LAMP
ZOOM/
FOCUSTEMP
VIDEO
ENTER
COMPUTER
MUTEAUTO
POSITION
MENU
3 , 9 , 103 , 9 , 10
444
5 , 75 , 7
6 , 86 , 8 
						

							EN – 14
Turning off the projector
9. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
•To exit from this mode,  press any button except
POWER, LASER, mouse pointer, R/L-click,
STILL and VOLUME + and - buttons.
10.Press the POWER button again.
The light source lamp will be turned off.
Pressing the POWER button second time  will shut
off the light source lamp, but the exhaust fan con-
tinues to operate for 120 seconds to cool down the
light source lamp and LCD panels. In this time, the
lamp indicator will be turned off.
11. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
•In cases where the main power switch is acciden-
tally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, set the screen to the
brightest display possible, then press the AUTO
POSITION button on the remote control. If the image
is still not in the right place.
•Set screen to the brightest display as possible
(e.g., full-screen display of the “Trash” window)
before deploying the automatic adjustment func-
tion.
•If the screen saver is running, turn off the screen
saver before using the automatic adjustment
button.
The volume from the speaker
Press the volume + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
•The volume control bar will disappear about 10
seconds after releasing the volume buttons.
•The volume buttons do not work when MENU
selection bar or MENU is displayed.
•The volume from the audio output terminals and
PC audio output terminal are not changed.
•If the high level of audio signal, for example DVD
is supplied into PC AUDIO IN terminal, the
speaker out may be distorted.
30
AV mute
Image and audio are temporarily erased with press-
ing the MUTE button. To restore the image and
audio to the normal mode, press the MUTE button
again.
•To prevent the damage of the LCD, the image and
audio will be restored automatically to the normal
mode, 10 minutes after setting the AV mute mode.
•The audios from the audio output terminals and PC
audio output terminal are not muted.
Caution:
•When you have finished using this equipment, wait
120 seconds for the exhaust fans to stop. Then turn
off the main switch and unplug the power cable from
the wall outlet, for safety purposes.
•After the lamp is turned off,  the lamp cannot be
switched on again for 60 seconds as a precaution-
ary measure. It will take another 60 seconds before
the lamp indicator goes off. If you wish to turn on
the projector again, wait until the indicator is off
then press the POWER button.
•The exhaust fan rotates faster when the tempera-
ture around the projector rises.
•When the temperature around the projector becomes
too high, the sign  “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically .
The projector automatically shuts off when the
lamp is used up in about 2,000. You must replace
the lamp.
To operate projector power ON (Continue) 
						

							EN – 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select the OPTION menu.
3.  Press the ENTER button (or } button).4.  Press the { or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
• If the menu operation is not working, press the
RESET button on the terminal board using the suit-
able implement
• If the COMPUTER or VIDEO button is pressed, the
MENU selection bar or MENU will disappear.
• The settings with 2 mark, you should press the
ENTER button after selecting.
Menu operation
Opt
PICTURE
Opt
INSTALLATION
TEST
Opt
IMAGE REVERSE
INSTALLATION
KEYSTONE 0˚
AUTO POWER ON ON
AUTO POWER OFF 0    min
TEST SIGNAL ON   OFFTESTTEST
R
AUTO POWER ON ON
AUTO POWER OFF0    min
TEST SIGNAL ON   OFFTEST
AUTO POWER ON ON
AUTO POWER OFF30  min
TEST SIGNAL ON   OFFTEST
PICTURE CONTRAST± 30
BRIGHTNESS
COLOR MATRIX± 30
1 (Standard)
2 (High)
3 (Low)
4     (User)  
COLOR TEMP.
SHARPNESS± 10
TINT± 10
COLOR± 10CONTRAST R± 30
CONTRAST B± 30
BRIGHTNESS R± 30
BRIGHTNESS B
(± 2 : When the source is selected to COMPUTER)
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)
(– : When the source is selected to COMPUTER)± 30
AUDIO BASS 0 - 3
TREBLE 0 - 3
PinP AUDIO           (Main) ,      (Sub)
INSTALLATION IMAGE REVERSE      (Off) ,      (Mirror) ,       (Invert) ,      (Mirror invert)
KEYSTONE± 15˚
AUTO POWER ON ON , OFF
TEST SIGNAL ON , OFF
AUTO POWER OFF
ON , OFF
ON , OFF
OPTION MENU POSITION      (Upper left),       (Lower right)
SPLASH SCREEN
0 (Off) , 5 , 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 55 , 60 min.
CINEMA MODE AUTO ,  OFF
MODE DISPLAY
VIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE
SIGNALHORIZ.POSITION 0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 32
TRACKING 0 - 9999
COMPUTER INPUT
USERRGB , YC
BCR , YPBPR
HOLD BEGIN 1 - 99
HOLD END 1 - 99
CLAMP POSITION 0 - 63
CLAMP WIDTH 0 - 63
ANAMORPHIC ON , OFF
*
*
*
*
*
*
* * : Setting range is different 
     according to the type of 
     the signal.
, English , Español , Deutsch , Français , Italiano ,
RRRR
1
RED± 10
YELLOW± 10
BLUE± 10
GREEN± 10
CYAN± 10
MAGENTA± 10
2 
3
USER
USER 
OFF 
						

							EN – 16
Opt
IMAGE REVERSE
INSTALLATION
KEYSTONE 0˚
AUTO POWER ON ON
AUTO POWER OFF
TEST SIGNALTEST
R
ON
0    min
ON   OFF
Opt
MENU POSITION
OPTION
MODE DISPLAY ON
SPLASH SCREEN ON
CINEMA MODE AUTO
VIDEO SIGNAL AUTO
LANGUAGE English
ON
ON
AË ?
1 PICTURE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
as the number increases.
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
the number increases.
COLOR MATRIX. ......Adjusts color balance in each color of the image. See page 18.
COLOR TEMP.. .. Adjusts color temperature. See page 18.
SHARPNESS ......Adjusts the picture sharpness. The sharpness becomes
sharper as the number increases.  (It can not be changed
on XGA resolution.)
TINT .................... Adjusts the color balance in the image.  The color balance
of the image shifts green as the number increases and shifts to purple as the number
decreases (displays only when the source is selected to VIDEO).
COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
2 AUDIO
BASS ................... Adjusts the level of low frequencies.
TREBLE .............. Adjusts the level of high frequencies.
PinP AUDIO ....... Use to select the audio output in the PinP mode, 
 (Main)
or 
 (Sub).
3 INSTALLATION
IMAGE REVERSEUse to reverse or invert the projected image.  R (Mirror)
is used for rear projection.  R (Mirror invert) is effective
when the projector is ceiling-mounted.
KEYSTONE ........ Adjusts keystone correction of the image. If the image has
keystone distortion, select the approximate setting. For
normal use, select 0˚.
AUTO POWER ON.....To select whether to boot up automatically when the power is
turned on external to the projector. In this case, the main
power switch of the projector has to be ON.  Set this when the projector is hanging on the ceiling.
• The projector is in stand-by mode when the lamp is not on. In this case, use the remote
control to turn on the lamp.
AUTO POWER OFF ..Use to select the length of time before projector switches to stand-by when there is no input
signal selected source. Select 0 min. to cancel this function.
TEST SIGNAL .... Use to display the built-in test patterns on the screen.
• The display will disappear when the setting is OFF or when you press any button except
MENU,  { ,}, STILL, LASER, mouse pointer or R/L-click.
4 OPTION
MENU POSITION .Use to select the position where the menu is displayed, 
(upper left) or  (lower right).
MODE DISPLAY ...Use to display the mode display on the screen.
SPLASH SCREEN .Use to display the splash screen on the screen when the
power is turned ON.
CINEMA MODE ....When AUTO is set, the video signal is processed
appropriately for cinema source during inputting the
cinema source with NTSC format. If the video signal is
processed during inputting the other source, set to OFF.
• When setting CINEMA MODE to AUTO, some images may not switch to cinema mode
during inputting the cinema source.
• When setting CINEMA MODE to AUTO, images may not switch to video mode immedi-
ately after switching the cinema source to video source. At that time, the image quality
of the video source may get worse. If you wish to switch the mode immediately, press
ENTER button.
VIDEO SIGNAL . When AUTO is set, the appropriate video format is automatically selected according to the
input signal. If the image does not appear correctly, select the desired video format
manually. Adjust the unit to the appropriate format when the unit either is not projecting
normally in auto mode or is projecting PAL-M/PAL-N signals.
LANGUAGE ....... Use to select the language for the projector display such as menu. (
 / English / Español
/ Deutsch / Français / Italiano / 
)
Opt
CONTRAST
PICTURE
0
BRIGHTNESS 0
COLOR TEMP. 1 / 2 / 3 / 4 
TINT 0
COLOR 0
SHARPNESS 0
COLOR MATRIXUSER
Menu operation (continued)
Opt
BASS
AUDIO
1
TREBLE 1
PinP AUDIO         / 
						

							EN – 17
ENGLISH
5 SIGNAL
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....The unit adjusts itself automatically when connected to
either DVD players with a component video output
terminal (YC
BCR or YPBPR) or equipment with HDTV
signal output capabilities. In cases where the unit is
connected to equipment that include an RGB output terminal and which output HDTV
signals, adjust the unit to RGB mode.
•In case of the HDTV, you cannot adjust the horizontal position and the vertical position of the image.
6 SIGNAL  - USER (Normally, there is no need for adjustments.)
HOLD BEGIN /
   HOLD END ...... Adjusts the image when curving near the top.
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
ANAMORPHIC ... Set to ON when displaying DVD discs which are recorded
as  squeezed images (in right and left direction).
HOLD BEGIN
USER
HOLD END 11
CLAMP POSITION 0
CLAMP WIDTH 0
ANAMORPHIC ON
USERR G B
Opt
HORIZ. POSITION
SIGNAL
VERT. POSITION 00
FINE SYNC. 0
TRACKING 0
COMPUTER INPUT RGBR G B 
						

							EN – 18
Adjusting the image
You can adjust the picture by using the IMAGE menu.
EXAMPLE: USER setting of COLOR TEMP.
1.  Select COLOR TEMP in IMAGE menu.
2.  Press the $ or % button to select 4 2.
3.  Press the ENTER button.
4.  Press the { or } button to select the desired item.
5.  Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjusting.
7. Exit the menu system by pressing the MENU but-
ton several times.
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu.  Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu.  Press the %
button to lighten the image and the $ button to
darken the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu.  Press the %
button to make the picture seem sharper and the $
button to make it softer.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu.  Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu.  Press the % button
to increase the amount of red in the image and the $
button to increase the amount of green in the image.
Color matrix
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using color matrix adjust-
ment. Use color matrix adjustment when enphasizing
a specific color, or when only a certain color balance
is not correctly adjusted.
1.  Select COLOR MATRIX in IMAGE menu.
2.  Press the ENTER button.When using the setting which has been already
prepared
3.  Press the $ or % button to select 1, 2, or 3.
•Select 1, 2 or 3 in the color matrix adjustment at
your option. Selecting VIDEO input automati-
cally selects 1 and selecting COMPUTER input
automatically selects 3. 2 is recommended for
images with high color temperature.
•Select OFF when not using Color matrix adjust-
ment
When using the user setting
4.  Press the $ or % button to select USER }.
5.  Press the { or } button to select the desired color.
6.  Press the + or - button to adjust the color balance of
the color.
7. Repeat steps 5 and 6 for more adjusting.
8. Exit the menu system by pressing the MENU but-
ton several times.
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers.  In this case, press the AUTO POSITION
button.  If the images are still not projected correctly,
use the MENU display to adjust the projected images.
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu.  Press
the % button to move the image to left.  Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu.  Press
the % button to move the image to upward.  Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Top part of image curves :
Adjust HOLD BEGIN or HOLD END in USER menu
for image which top part is the least curved.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL -
USER menu.  Select AUTO for normal setting.
•Do not change each menu setting in USER menu
for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left end).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right end).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end).
Picture adjustment
CONTRAST R
COLOR TEMP.
0
CONTRAST B 0
BRIGHTNESS B 0
BRIGHTNESS R 0
COLOR MATRIX
RED 0
BLUE 0
CYAN 0
MAGENTA 0 YELLOW 0
GREEN0
123USER OFF 
						

							EN – 19
ENGLISH
Specification of RGB signals in each computer mode of the projector
•Pressing the EXPAND button on the remote control
twice will switch to the screen displaying the pic-
ture as its original size (real screen display).  In the
real screen display, pictures will be black-framed
when picture resolution is lower than 800 x 600.
Important:
•Some computers may not be compatible with the
projector.
•The projectors maximum resolution is 1,024 x 768
pixels.  It may not display correctly for the pictures
of higher resolutions than 800 x 600.
•The picture with a SYNC on G (Green) signal may
jitter.
•The picture with a SYNC on G (Green) signal may
be tinged with green.•If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible reso-
lution and frequency.
•Set the COMPUTER INPUT in SIGNAL menu to RGB,
when inputting the HDTV signal as RGB signal.
•In case of the HDTV, the image quality may be
reduced, principally.
Signal mode resolution horizontal Vertical Normal mode Real mode
 (H x V) frequency (kHz) frequency (Hz) (H x V)  (H x V)
TV60–15.73 59.94 800 x 600–
TV50–15.63 50.00 800 x 600–
HiVision–33.75 60.00 800 x 450–
PC98 640 x 400 24.82 56.42 800 x 500 640 x 400
CGA70 640 x 400 31.47 70.09 800 x 500 640 x 400
CGA85 640 x 400 37.86 85.08 800 x 500 640 x 400
VGA60 640 x 480 31.47 59.94 800 x 600 640 x 480
VGA72 640 x 480 37.86 72.81 800 x 600 640 x 480
VGA75 640 x 480 37.50 75.00 800 x 600 640 x 480
VGA85 640 x 480 43.27 85.01 800 x 600 640 x 480
SVGA56 800 x 600 35.16 56.25 800 x 600 800 x 600
SVGA60 800 x 600 37.88 60.32 800 x 600 800 x 600
SVGA72 800 x 600 48.08 72.19 800 x 600 800 x 600
SVGA75 800 x 600 46.88 75.00 800 x 600 800 x 600
SVGA85 800 x 600 53.67 85.06 800 x 600 800 x 600
XGA43i 1024 x 768 35.52 86.96 800 x 600 800 x 600
XGA60 1024 x 768 48.36 60.00 800 x 600 800 x 600
XGA70 1024 x 768 56.48 70.07 800 x 600 800 x 600
XGA75 1024 x 768 60.02 75.03 800 x 600 800 x 600
XGA85 1024 x 768 68.68 85.00 800 x 600 800 x 600
MAC13 640 x 480 35.00 66.67 800 x 600 640 x 480
MAC16 832 x 624 49.72 74.55 800 x 600 800 x 600
MAC19 1024 x 768 60.24 75.02 800 x 600 800 x 600
MAC21 1152 x 870 68.59 74.96 800 x 600 800 x 600
HP75 1024 x 768 62.94 74.92 800 x 600 800 x 600 
						

							EN – 20
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote con-
trol, you can view the detailed image of the picture.
You can also view the screen diplaying the picture as
its original size (real screen display) by pressing the
button again.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active pic-
ture by pressing the {, }, $ or % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The real screen display will appear on the screen.
3. Press the COMPUTER or VIDEO button.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
• In EXPAND mode or REAL mode, pressing the
COMPUTER or VIDEO button will switch to the
normal screen display .
The normal screen display will appear on the screen.
• In EXPAND mode, you cannot adjust the zoom/fo-
cus and the volume.
• When displaying the images through VIDEO IN
terminal or the video images through COM-
PUTER IN terminal, expanded image display is
not available. Only real screen display is avail-
able.
• During expand mode, the PinP mode is not avail-
able.
REAL screen display
• During REAL mode, Press the $ or % buttons
for fine adjustment. the  { and } buttons are
not working at this time.
• The expanding rate cannot be changed by
pressing either the + or - button. They are
working for volume adjustment.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will stop temporary.
To resume picture activity.
2. Press the STILL button on the remote control
again.
PinP (Picture in Picture)
One of the special features of this unit is the picture-
in-picture (PinP) mode. PinP allows you to view differ-
ent sources at the same time.
1. Press the PinP button on the remote control.
The sub image will appear.
• Pressing the PinP button repeatedly will select
on and off.
• You can change the position of the sub image by
pressing the {, }, $ or % button.
• You can change the size of the sub image by
pressing the + or - button.
2. If necessary, select the desired external input source
of the sub image by using the VIDEO button.
• You can change the external input source of the
main image by using the COMPUTER button.
3. Press the PinP button on the remote control again.
The sub image will be disappeared.
• During PinP mode, the audio selected in PinP
AUDIO of the AUDIO menu is outputted.
• During PinP mode, you cannot adjust the zoom/focus
and the volume.
• Adjusting contrast, brightness, tint or color isnt
available during PinP mode.
• When connecting DVD player or MUSE decoder
etc. to COMPUTER IN terminal, PinP are not
available.
• During PinP mode, the expand mode is not avail-
able.
Main image
(From COMPUTER IN)
Sub image
(From VIDEO IN)