Mitsubishi S290u Projector User Manual

							EN – 1
ENGLISH
S 290
LCD
Projector
User Manual
MODEL   S290U 
						

							EN – 2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE IN-
STALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interfer-
ence with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class A device.
This apparatus must be grounded.
The projector automatically shuts off when the
lamp is used up in about 2,000 hours and cannot
be used until  lamp replacement.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.When using the projector in Europe
COMPLIANCE NOTICE
This LCD - Video Projector complies with the
requirements of the EC Directive 89/336/EEC “EMC
Directive” as amended by Directive 93/68/EEC and
73/23/EEC “Low Voltage Directive” as amended by
Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of  the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B and EN55013. Please
follow WARNINGS instructions. 
						

							EN – 3
ENGLISH
Contents
Important safeguards ........................................................................... 4
Overview ............................................................................................... 6
Using the remote control ...................................................................... 8
Battery installation ......................................................................................................... 8
Installation ............................................................................................ 9
Basic connections ............................................................................... 10
Projector + AV equipment ............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer ...................................................................................... 10
For IBM PC or IBM PC compatibles ................................................................. 11
For Macintosh .................................................................................................... 11
Preparing the projector for operation ............................................... 12
To operate projector power ON .......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment ............................................................................. 18
Advanced feature for presentation .................................................... 20
PinP (Picture in Picture) ............................................................................................... 20
Expand ........................................................................................................................... 20
Still ................................................................................................................................. 20
Mouse remote control .................................................................................................... 21
Lamp replacement ............................................................................. 22
Maintenance ....................................................................................... 23
Troubleshooting .................................................................................. 24
Indicators ............................................................................................ 25
Specifications ...................................................................................... 26
Kensington Lock ............................................................................................................ 26
Connectors .....................................................................................................................27
Dimensional drawings .................................................................................................. 27
Replacement parts list .................................................................................................. 27
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
IBM and PS/2 are trademarks or registered trademarks of International Business Machines Corporation.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders. 
						

							EN – 4
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD pro-
jector.
1. Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the oper-
ating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet be-
fore cleaning it. Do not use liquid aerosol clean-
ers. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, elec-
tric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in con-
tact with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow the
manufacturers instructions and should use a
mounting accessory recommended by the manu-
facturer.10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular at-
tention to cords at plugs, convenience receptacles,
and points where they exit from the appliance. Do
not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through open-
ings of this projector as they may touch danger-
ous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liq-
uid of any kind on the projector.
14. Servicing
Do not attempt to service this projector yourself.
Refer all servicing to qualified service person-
nel.
15. Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel un-
der the following conditions:
(a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require exten-
sive work by a qualified technician to re-
store the projector to its normal operation.
(d) If the projector has been exposed to rain
or water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturers instruc-
tions have been adhered to. 
						

							EN – 5
ENGLISH
WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owners
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not look into the lens when it is
operating.
It may hurt your eyes.Never let children look into
the lens when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
Do not touch Air outlet grill and Bottom
plate which becomes hot.
Do not touch them or put other equipment in front of
Air  outlet grill. The heated Air outlet grill and Bot-
tom plate may cause injury or damage to other equip-
ment. Also, do not set the projector on the desk which
is easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventila-
tion slots become clogged with dirt or dust, the tem-
perature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Do not look into the air outlet grill when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
•Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
•Operating humidity:  between 30 and 90%
•Never put any heat-producing device under the pro-
jector so that the projector does not overheat.
•Do not attach the projector to a place that is un-
stable or subject to vibration.
•Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
•Place the projector on a solid, vibration free sur-
face: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the prod-
uct.
•Do not stand the projector: it may fall, causing se-
rious injury and damage to the projector.
•Place the projector within a slope of ±15˚. Slanting
the projector more than ±15˚ may cause trouble or
explosion of the lamp.
•Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and venti-
lation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in
the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of Communica-
tions.
Changes or modifications not expressly approved by Mitsubishi could void the users authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003. 
						

							EN – 6
Overview
LAMP
VOLUMEZOOM/
FOCUSTEMP
VIDEO
ENTER COMPUTER
MUTE
AUTO
POSITION
MENU
1
2
3
4
511
10
9
8
7
6 14 13 12
4
765
123
89 10
L
RAUDIO VIDEO S-VIDEO
MAIN
AC INAUDIO OUT
VIDEO 1 IN VIDEO 2 IN
COMPUTER OUTAUDIO 2 INCOMPUTER 2 INAUDIO 1 INCOMPUTER 1 IN
OI
1
2
34567 8 9
10 11 12 13 14
REMOTE
USBRS-232C
Control panel
Terminal board
1 Air inlet slots (Front)
2 Terminal board
3 Air outlet slots
4 Speaker (Left/Right)
5 Control panel
6 Remote control sensor (Front)
7 Lens
8 Remote control sensor (Rear)
9 Kensington Security Lock Standard
connector
10 Easy-carry handle
1 Power button
2 – (VOLUME) button
3 COMPUTER button
4 MENU button
5 AUTO POSITION button
6 MUTE button
7 Direction buttons
8 ENTER button
9 VIDEO button
10 + (VOLUME) button
11ZOOM/FOCUS button
12 Temperature (TEMP) indicator
13 LAMP indicator
14 Power indicator
1 Main power
I : ON
O : OFF
2 Ground terminal
3 Power jack
4 COMPUTER OUT terminal
5 Audio output jack
6 Video/audio input terminals
7 Reset button
8 Wired remote control (REMOTE) jack
9 USB terminal
10 Audio input 2 (AUDIO 2 IN) terminal
11RS-232C terminal
12 COMPUTER 2 IN terminal
13 Audio input 1 (AUDIO 1 IN) terminal
14 COMPUTER 1 IN terminal 
						

							EN – 7
ENGLISH
Bottom side
1
3 2
4 51 Release buttons (Left/Right)
2 Adjustment foot (Left/Right)
3 Air inlet cover (bottom) /
Filter cover (For bottom air inlet slots)
4 Lamp cover
5 Filter cover (For front air inlet slots)
Caution:
Do not replace the lamp right after using the projector.
The lamp is very hot.
Remote control1 Power button
2 COMPUTER button
3 AUTO POSITION button
4 MENU button
5 RIGHT CLICK button (For mouse)
6 EXPAND button
7 Wired remote control jack
8 Picture in Picture (PinP) button
9 STILL button
10 Direction buttons
11ENTER button
12 Mouse pointer button
13 LASER button
14 + , – buttons
15 ZOOM/FOCUS button
16 VIDEO button
17 MUTE button
18 Remote control transmitter
19 Laser aperture
20 Left click button (For mouse)
ENTER
RIGHT CLICKLASER
COMPUTERVIDEOZOOM/
FOCUS
MUTE
VOLME
AUTO
POSITION
MENU
P in P EXPAND STILL
1
2
3
4
5
6
8 16 1817
15
14
13
12
11
9
20 1910
7
About laser beam
This remote control is class 2 (max. output 1 mW laser diode
640 - 660 nm) laser equipment.
Beam Divergence : 6m distance about 10.0mm x 10.0mm (±6.0mm)
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH : 640 - 660 nm
MAX OUTPUT : 1 mW
CLASS 2 LASER PRODUCT
IEC 60825-1:1993+A1:1997
CAUTION
CAUTION :
•Pressing the LASER button provided remote control emits
laser beam. Do not look into the beam light directly. Do not
point the laser beam at people. Looking the laser beam directly
may damage eyesight.
•Use of controls or adjustments or procedures other than those
specified herein may result in hazardous radiation exposure.
AVOID EXPOSURE -LASER
RADIATION IS EMITTED
FROM THIS APERTURE. 
						

							EN – 8
Battery installation
Use two AA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
3. Replace the back cover.
Important:
•Do not use a new battery with an old one.
•Load batteries in the correct position.
•Do not heat, take apart, or throw batteries into fire.
•Do not try to recharge batteries. Do not use rechargeable batteries.
•If the solution of batteries comes in contact with your skin or clothes, rinse with water. If  the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area (for wireless control system)
The range for operation is about 10 m when the remote control points to the projector. The distance to the screen
back to the projector must be less than 7 m. Depending on the type of the screen, the distance is different.
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
Using the wired remote control
Attached remote control for this projector can be used as a wired remote control with remote control cable. Wired
remote control is useful for operating in a distance or outside of the operating area.
20˚
15˚20˚
15˚
30˚ 30˚
20˚20˚
12 3
L
RAUDIO VIDEO S-VIDEO
MAIN
AC INAUDIO OUT
VIDEO 1 IN VIDEO 2 IN
COMPUTER OUTAUDIO 2 INCOMPUTER 2 INAUDIO 1 INCOMPUTER 1 IN
OI
REMOTEUSBRS-232C
•When the remote control is connected with remote
control cable, it does not work as a wireless
remote control.
•When you need a longer cable, use a pin-pin cable.
•When using the wired remote control, the laser beam may be darker. It is normal.
Using the remote control 
						

							EN – 9
ENGLISH
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
To find the approximate distance
between the projector and screen:
Multiply the width of the screen
✕ 1.9 (min.) , Multiply the width of
the screen 
✕ 2.4 (max.).
• Refer to the chart for recom-
mended distances in maximum
zoom and minimum zoom.
SCREEN
Front projection, ceiling mount
For ceiling mount, you need the ceiling mount kit.
Ask a specialist for installation. For more details,
consult your dealer.
•When using the ceiling mount, set IMAGE RE-
VERSE in the INSTALLATION menu to 
R
(Mirror invert). See Page 16.
•Projected images may appear darker when the
unit is used as a ceiling installation than when it
is used in the tabletop position. This does not
signify a product malfunction.
Rear projection
Ask a specialist for installation.  For more details,
consult your dealer.
SCREEN
•For rear projection, set IMAGE REVERSE in the
INSTALLATION menu to 
R (Mirror).  See Page
16.
Caution:
•Placing the projector on a carpet reduces ventila-
tion from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
•Place the projector more than 20 in. from the wall
to prevent blocking the intake, exhaust slots and
ventilation of this projector because hot air comes
out of it.
•Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
•in a dusty or humid place
•while the projector is lying sideways or upside
down
•near a heater
•in a kitchen or oily, smoky or damp place
•in direct sunlight
•with high temperature, such as the closed car
•where the temperature is lower than 41°F or
higher than 104°F
Important:
•Do not put stress on the lens, as this may cause
damage.
L (between the screen and the 
head of the projector)
screen
• The above numbers are approximate, and may be slightly different from the actual measurements.
Diagonal size
 (inch)
40 
60 
80 
100 
120 
140 
160 
180
200 
300 
Height inches
 (inch)
24 
36 
48 
60 
72 
84 
96 
108 
120 
180 Width feet
 (inch)
32 
48 
64 
80 
96 
112 
128 
144 
160 
240 
ScreenDistance from screen (L) / (approximate)
Maximum
zoom (min.)
(cm)
155
235
315
394
474
554
634
714
794
1194(cm)
195
296
396
496
597
697
797
898
998
– (inch)
61 
92 
124 
155 
187 
218 
250 
281 
312 
470 (inch)
77 
116 
156 
195 
235 
274 
314 
353 
393 
–
Minimum
zoom (max.) 
						

							EN – 10
Basic connections
This projector can be connected to equipment such as VCRs, video cameras, videodisc players, and personal com-
puters having analog RGB output.
Important:
•Make sure that your equipment is turned off before connection.
•Plug in firmly and unplug by holding the plug, not by pulling the main power cable.
•If connected units are set too close to one another, the image may be affected.
•Refer to the owners guide of each component for details of connections.
Projector + AV equipment
Important:
•Match the color of video and audio plugs on the AV cable with the connections.
•S-video signals take priority over video signals. If you input both S-video signals and normal video signals at
the same time, the normal video input automatically is inhibited.
to audio
outputto video
outputto S-video
output to audio
outputto video
outputConnect either one of these.
Connect 
either one 
of these.
DVD player, others
to audio 
input 2
to S-video 
input 2
to S-video
output
to S-video 
input 1
to video 
input 2
to audio input 1
to video 
input 1
VCR, others
to COMPUTER
 1 IN B G R HD/CS
VD 
DVD player or HDTV decoder
No connectionCB(PB) YCR(PR) 
BNC - RCA connector 
(optional)
Mini D-SUB 15pin-BNC
conversion cable (optional)
Projector + DVD player or HDTV decoder
Some DVD players have output terminal for 3 line fitting (Y, CB, CR). When connecting them to the projector,
connect to COMPUTER 1 IN or COMPUTER 2 IN of the projector. In this case, set “ Y,  C
B, CR” for COMPUTER
INPUT setting in SIGNAL menu.
Connecting with DVD player
DVD player generally has SDTV system compo-
nent video output (Y, C
B, CR) terminal. When con-
necting the projector with DVD player, the COM-
PUTER INPUT in the SIGNAL setting menu be-
comes [Y, C
B, CR] automatically.
Connecting with HDTV decoder
Many HDTV decoders have HDTV system compo-
nent video output (Y, P
B, PR) terminal. When con-
necting the projector with this type of HDTV de-
coder, the COMPUTER INPUT in the SIGNAL
setting menu becomes [Y, P
B, PR] automatically.
•Y,  PB, PR is an example of the terminal names for a HDTV decoder.
•The terminal name is different depending on the connected equipment.
•Use mini D-SUB 15 pin-BNC conversion cable for connection.
•Some DVD players may not project the image correctly.
•When connecting with HDTV equipment which has R, G, B output, set RGB for the COMPUTER INPUT in the SIGNAL
setting menu.