Mitsubishi S120 Projector User Manual

11
ENGLISH
Adjusting the angle of projection
Screen on a flat wall with a 90 degree angle to the floor
by adjusting two Adjustment feet on the bottom of the
projector.  If the angle cannot be corrected by them,
adjust the height and angle of screen.
1. Lift the projector to the right angle.
2. Press the release button for angle adjustment to take
the Adjustment foot (up and down) out of the pro-
jector.
3. Release the button and keep your hands away from
the projector.
4. Turn the foot to right or left...

12
Cables and adapters
To connect personal computers to this projector, the following cables and adapters are necessary.  The overview
might be different from the picture below.
RGB cable for PC (mini D-SUB 15P plug)
Note: The pins numbered 9, 12 and 15 are not connected.
MAC adapter for RGB cable
 (mini D-SUB 15P plug - D-SUB 15P plug)
Basic connections
This projector can be connected to equipment such as VCRs, video cameras, videodisc players, and personal comput-
ers having analog RGB input....

13
ENGLISH
Projector + IBM PC or IBM PC compatibles
Make sure that your equipment is turned off before connection.
Important:
•Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
•The audio input for a personal computer is the stereo mini-jack. There are some personal computers that have
different types of audio outputs or none at all. Please ask your dealer for details.
•For connection details, refer to...

14
Projector + Macintosh
Make sure that your equipment is turned off before connection.
Important:
•A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
•If you use the MAC adapter for RGB cable provided, set the dip switch to the appropriate position. See page 12.
•Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to
this projector.  Please contact your dealer.
•The audio input for a personal...

15
ENGLISH
To operate projector power ON
Numbers 1 - 9 correspond to the instruction numbers below.
Important:
•A darkened image may be seen right after pressing
the POWER button  due to warming up of this pro-
jector. While warming up, no other commands can
be accepted.
•When the lamp indicator is blinking red, the ser-
vice life of the lamp is about to end.  Replace the
lamp. See pages 32 and 36.
•The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not...

16
AUTO POSITION button
When the source is selected to RGB and the image is
not in the right place, set to display as blight signal
as possible, then press the AUTO POSITION button
on the remote control. If the image is still not in the
right place.
•Set screen to the brightest display as possible
(e.g., full-screen display of the “Trash” window)
before deploying the automatic adjustment
function.
•If the screen saver is running, turn off the screen
saver before using the automatic adjustment
button.
5....

17
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1.  Press the MENU button.
2.  Press the $ or % button to select OPTION menu.
3.  Press the ENTER button (or { or } button).4.  Press the{ or } button to select AUTO POWER
OFF.
5.  Press the $ or % button to adjust auto power off
time.
6.  Exit the menu system by pressing the MENU but-
ton several times.
• If the menu operation is not working, simultaneously
press the MENU and POWER buttons.
• The...

18
1 PICTURE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
as the number increases.
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
the number increases.
COLOR TEMP .... Adjusts color temperature.
TINT .................... Adjusts the color balance in the image.  The color balance
of the image shifts green as the number increases and
shifts to purple as the number decreases (only when
NTSC or 4.43 NTSC is selected).
COLOR ................Adjusts the...

19
ENGLISH
5 SIGNAL
AUTO .................. Use to select AUTO, USER 1 or USER 2.
HORIZ. POSITION ....Use to adjust the horizontal position of the image.
VERT. POSITION .....Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
RGB INPUT ........ The unit adjusts itself automatically when connected to
either DVD players with a component...

20
Adjustment from personal computer
Although this projector sets proper signal settings set
automatically for the image signal from personal
computers. But, at times, there can be dome
diferences in timings.  In this case, press AUTO
POSITION button.  If the images are still not pro-
jected correctly, use MENU display to adjust the
projected images from personal computers.  After
adjustments are made, the new settings can be saved
in user function.
Adjusting the images form personal
computers in MENU...