Mitsubishi Projector Xd2000u User Manual

							EN-21
ENGLISH
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the 
setting according to the type of the input video signal. 
How to change the settings:
With the remote control:
1.  Press the ASPECT button. 
•  Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 16:9, to REAL, and back to 
AUTO. 
•  When the keystone adjustment is applied, the REAL mode can not be selected.
With the FEATURE menu:
(See page 22 for menu setting.) 
1.  Display the FEATURE menu. 
2.  Select ASPECT by pressing the 

 or 
 button. 
3.  Select your desired aspect ratio by pressing the 
 or 
 button. 
When 16:9
 is selected:
4.  Press the ENTER button. 
5.  Select your desired position  by pressing the 
 or 
 button.
To cancel the menu:
6.  Press the MENU button. 
Important :
•  When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars 
may appear on the 4:3 image screen. Consult your dealer in this case.
FEATURE
AUTO
XGA60opt.
ASPECT 
						

							EN-22
Menu operation
•  Menus are not displayed when no signal is supplied to the projector. 
* 1: Not available when COLOR ENHANCER is set to sRGB.
* 2: Not available with certain signals.
* 3: Available only when the input signal is TV50, TV60, 480i or 576i.
* 4: Available only when the source is a COMPUTER/COMPONENT 
VIDEO IN-1.
* 5: Setting range differs depending on the input signals.
* 6: Not available when the source is VIDEO IN or S-VIDEO IN.
How to set the menus:
Following describe how to set AUTO POWER OFF 
time. 
1.  Press the MENU button. 
•  When no signal is input, the menu does not appear. 
2. Press the 
 or 
 button to select a menu to use.  
3.  Press the ENTER button (or 
 button).
IMAGE
XGA60opt.
INSTALLATION
opt.XGA60
AUTO POWER 
OFFOFF OFF AUTO POWER 
ON
4. Press the 

 or 
 button to select an item to adjust. 
5.  Set the selected item by pressing the 
 or 
 button. 
To cancel the menu:
6.  Press the MENU button several times. 
Important:
•  If the menu operation is not working, turn off the 
main power, wait about 10 minutes, and turn on the 
main power again. 
•  After selecting the items marked with 
, press the 
ENTER button.
OFF AUTO POWER 
ONOFFAUTO POWER 
OFF
30min AUTO POWER 
ONOFFAUTO POWER 
OFF
INSTALLATION
CENTER, UPPER, LOWER
OFF, MIRROR, INVERT, MIRROR INVERT AUTO POWER ON
ON , OFF
RESET ALL OK  AUTO POWER OFF
ON , OFF
FEATURE
MENU POSITION 1 (Upper left), 2(Lower right) IMAGE REVERSE SPLASH SCREEN
BLUE, BLACK BACK COLORSTANDARD, LOW LAMP MODEAUTO16:9REAL ASPECTDISPLAY INPUTPASSWORD FUNCTION
ON , OFF SCART INPUT
VIDEO SIGNAL AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60
LANGUAGE
, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
SIGNALHORIZ.POSITION
HOLD
SETUP
0 - 999VERT.POSITION 0 - 999FINE SYNC. 0 - 31
TRACKING
USER0 - 9999
CLAMP POSITION1 - 63CLAMP WIDTH 1 - 63
LPF
ON , OFF
OVER SCAN
100 - 90%
SHUTTER (L)
0 - 38SHUTTER (U)
0 - 38
SHUTTER (RS)
0 - 63SHUTTER (LS)
0 - 63
VERT. SYNC
AUTO, OFF *5
*6 *7
*2 *6 *7*7
*7
*6 *2 *7
*2 *6 *7*4
AUTO , OFF CINEMA MODE
*6 *7
*6 *7 *6 *7 *5
*5
OFF
BEGIN 0 - 99END 0 - 99
COMPUTER INPUTAUTO, RGB, YCBCR / YPBPR
AUTO, OFF, 3.75%, 7.5%
*2 *5
OFF,  5,  10,  15,  30,  60 min
OK , MENU ACCESS
OKON
UNLOCKOK LOCK
*3
*8
IMAGE
CONTRAST ±30
BRIGHTNESS ±30STANDARDLOWHIGH
COLOR ENHANCER AUTOPRESENTATIONSTANDARDTHEATERsRGB
USER     COLOR TEMP.COLOR  ±10TINT  ±10SHARPNESS  ±5CONTRAST B  ±30
BRIGHTNESS R  ±30BRIGHTNESS G  ±30
CONTRAST R  ±30CONTRAST G  ±30
GAMMA MODE DYNAMIC, NATURAL, DETAILBrilliantColorTM0 - 10
BRIGHTNESS B  ±30USER    
*1
*2
*1*2
*1
*2
*2
*2
*2
*2
CROSS HATCH     TEST PATTERNON , OFF
ZOOM/FOCUS LOCK
LENS SHIFT LOCK
LENS SHIFT RESET
OKON , OFF
* 7: Not available when the source is DVI.
* 8: Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal. 
						

							EN-23
ENGLISHIMAGE
opt.
CONTRAST
BRIGHTNESS0
0
STANDARD
0 0
0 COLOR
TINT
SHARPNESS
COLOR TEMP.
AUTO COLOR
ENHANCER
XGA60INSTALLATION
opt.
ONSPLASH 
SCREENAUTO POWER 
OFF
BACK COLOR
LAMP MODE
OFF OFF
ON
BLUE AUTO POWER 
ONSTANDARD
OFF IMAGE 
REVERSE
XGA60
TEST PATTERNCROSS HATCH
ZOOM/FOCUS 
LOCK
OFF OFF
LENS SHIFT LOCKLENS SHIFT 
RESETOK
FEATUREAUTO
XGA60
AUTO
opt.
MENU POSITION
VIDEO SIGNAL?
ASPECT
RESET ALLEnglish
LANGUAGEAËOK
SCART INPUT
DISPLAY INPUT PASSWORD
FUNCTION
CINEMA MODEAUTO1.
SET UP
AUTOOFF
R G BR G B
SIGNALHORIZ. POSITION 0
VERT.POSITION 0
TRACKING 0
COMPUTER 
INPUTRGB
FINE SYNC. 0
USER
opt.
OK
OFFHOLD
XGA60
Available settings in the menus
Set the following items on their relevant menus.  
1. IMAGE menu  2. INSTALLATION menu  3. FEATURE menu  4. SIGNAL menu
1. IMAGE menu
ITEM SETTING FUNCTION
COLOR ENHANCER AUTO  Select to optimize the settings automatically depending on the input signal.  
(Select this option for normal use.)
 
PRESENTATION  Select to make the displayed image look bright and crisp.
  STANDARD  Select to make the displayed image look natural.
  THEATER  This option, suitable for viewing movies, makes the displayed image look soft 
and smooth.
  sRGB  Select to give priority to the color reproducibility.
 
• When COLOR ENHANCER is sRGB, COLOR TEMP., COLOR and TINT can't 
be adjusted.
 USER 
  Select to set the gamma curve and BrilliantColorTM as desired. (See page 26.)
CONTRAST ±
30  Use to adjust the contrast of the projected image. (See page 25.)
BRIGHTNESS ±
30  Use to adjust the brightness of the projected image. (See page 25.) 
COLOR TEMP. 
  4 options  Use to adjust the color temperature. (See page 26.) 
COLOR ±
10  Use to adjust the color thickness of the projected image. (See page 25.)
TINT ±
10  Use to adjust the color tint of the projected image. (See page 25.) 
 
• When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted.
SHARPNESS ±
5  Use to adjust the sharpness of the projected image. (See page 25.)
2. INSTALLATION menu
ITEM SETTING FUNCTION
LAMP MODE  STANDARD  Select this option when you want to view images in a well-lit room.
  LOW  Select to moderate the intensity of the lamp. The operating sound is reduced 
and the lamp lifetime becomes longer. 
•  When the lamp mode is switched, the projected image may fl icker. This is 
not a product malfunction. 
•  Frequent switching of the lamp mode may damage the lamp.
AUTO POWER ON  ON / OFF When ON is chosen, the lamp is automatically lit when the power cord is 
plugged in the wall outlet. Choose ON when using the projector mounted on 
the ceiling.
•  The projector is in the stand-by mode when the lamp is off.  Use the remote 
control to turn on the lamp. 
  
AUTO POWER OFF  OFF / 5 - 60min 
Use to set the time elapsed before the projector enters the stand-by mode 
when there is no signal input from the source. 
SPLASH SCREEN   ON / OFF  Choose ON to display the splash screen when the power is turned on. 
BACK COLOR  BLUE / BLACK  Use to change the color of the screen that appears when no signal is supplied. 
IMAGE REVERSE  OFF  Select when viewing images from the front with the projector installed on the 
fl oor. 
  MIRROR  Select when viewing images projected from the behind of the screen with the 
projector installed on the fl oor.  
  INVERT  Select when viewing images projected from the behind of the screen with the 
projector installed on the ceiling. 
  MIRROR INVERT  Select when viewing images from the front with the projector installed on the 
ceiling.
TEST PATTERN CROSS HATCH 
  Use to show the test pattern of the crossing hatch.
ZOOM/FOCUS LOCK  ON / OFF  Use to enable or cancel the FOCUS LOCK and  ZOOM LOCK.
LENS SHIFT LOCK  ON / OFF  Use to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESET OK   Use to reset the position of the lens to the factory setting. 
•  Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default 
whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to 
LOW about 1 minute after turn-on. 
•  To cancel the test pattern, press any button.  
						

							EN-24
3. FEATURE menu
ITEM SETTING FUNCTION
ASPECT  AUTO  Select to change the aspect ratio automatically depending on the input signal.   
(Select this option for normal use.) 
 16:9 
  This option allows you to select the display position of squeezed (or horizontally 
compressed) images stored on DVD discs. By pressing the ENTER button, you 
can select the display position among CENTER, UPPER, and LOWER.
  REAL  Select to project images in their original size as input. Not available when the 
keystone adjustment is applied.
PASSWORD FUNCTION  Use to enable or cancel the password lock. See page 28 for details.
MENU POSITION   2 options  Use to change the position of the menu. 
CINEMA MODE
 AUTO The fi lm mode will be automatically activated when a fi lm source signal is input. 
 OFF The fi lm mode will not be activated. 
VIDEO SIGNAL  8 options When AUTO is selected, the appropriate video format is automatically selected 
depending on the input signal. If the image isn’t displayed correctly, select the 
desired video format manually.
SET UP  AUTO  Select to change the SET UP mode automatically.
  OFF  Select to make black lighter. 
  3.75%/7.5%  Select to make black thicker. 
•  When 7.5% is chosen, the brightness is decreased by set-up cancel func-
tion for U.S. Choose OFF when the image is dark.
SCART INPUT  ON / OFF  Choose ON when connecting the projector with a device equipped with the 
SCART terminal that can output RGB signal. SCART terminal is used mainly 
in Europe. Choose OFF normally. (Available only for the input signal from the 
COMPUTER/COMPONENT VIDEO IN terminal.)
LANGUAGE  10 languages  Use to select the language used in the menus. 
RESET ALL  OK 
  Use to reset the settings of the menu (excluding PASSWORD FUNCTION and 
LANGUAGE) to the factory setting values. 
•  When SCART INPUT is set to ON, nothing is output to the external monitor.
•  When SCART INPUT is set to ON, normal computer signals arent projected. 
•  Use a SCART-BNC (or SCART-Mini D-SUB 15P) cable (option) when connecting this projector with an AV device 
equipped with the SCART terminal.
•  Some AV devices equipped with the SCART terminal arent compatible with this projector.
•  It may take a little while to carry out RESET ALL in the FEATURE menu.
4. SIGNAL menu
ITEM SETTING FUNCTION
HORIZ. POSITION  0-999  Use to adjust the horizontal position of the projected image. 
VERT. POSITION  0-999  Use to adjust the vertical position of the projected image. 
FINE SYNC.  0-31  Use to eliminate fl ickering or blur, if appears, viewing the projected image. 
TRACKING  0-9999  Use to eliminate vertical wide stripes, if appears, viewing the projected image.
COMPUTER INPUT  AUTO  The proper setting is automatically selected.
  RGB  Select this option if colors aren’t displayed correctly when a high-defi nition video 
device having R, G, and B outputs is connected. 
 YC
BCR/YPBPR  Select this option if colors aren’t displayed correctly when 480p (525p) signal is 
input from a DVD player having Y, C
B, and CR component video output terminals 
or a high-defi nition digital tuner having Y, P
B, and PR component video output 
terminals. 
HOLD OFF/ON 
  Use to adjust the image when fl agging occurs near the top of the screen.
USER OK 
  CLAMP POSITION 1-63   Use to correct solid white or solid black in the projected image.
  CLAMP WIDTH   1-63  Use to correct solid black in the projected image. 
  VERT.SYNC  AUTO/OFF  Use to adjust the image when its motion doesn't run smoothly.  Select AUTO 
for normal use.
  OVER SCAN  100%-90%  Use to adjust the display area of projected image.
  LPF    Use to select whether or not to enable the LPF.
  SHUTTER (U)  0-38  Use to adjust the image when noise appears on the top part of the image.
  SHUTTER (L)  0-38  Use to adjust the image when noise appears on the bottom part of the image.
  SHUTTER (LS)  0-63  Use to adjust the image when noise appears on the left half of the image.
  SHUTTER (RS)  0-63  Use to adjust the image when noise appears on the right half of the image.
Menu operation  (continued) 
						

							EN-25
ENGLISH
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 22 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the 

 or 
 button. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the 
 button is pressed, the image becomes brighter and more 
defi ned. Every time the 
 button is pressed, the image becomes darker and less defi ned.
BRIGHTNESS
Every time the 
 button is pressed, the image becomes brighter. Every time the 
 button is pressed, the image 
becomes darker. 
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu. 
(See page 22 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR or TINT by pressing the 

 or 
 button.  
•  COLOR or TINT is not available with certain signals. 
•  TINT is available only when the NTSC signal is input. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
COLOR 
Use to adjust the color thickness of the projected image. Every time the 
 button is pressed, the color becomes 
thicker. Every time the 
 button is pressed, the color becomes lighter. 
TINT
Use to adjust the tint of the projected image. Every time the 
 button is pressed, the image appears more greenish.  
Every time the 
 button is pressed, the image appears more reddish. 
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu. 
(See page 22 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select SHARPNESS by pressing the 

 or 
 button. 
•  SHARPNESS is not available with certain signals. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button.  
						

							EN-26
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 22 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR TEMP.  by pressing the 

 or 
 button. 
3.  Select your desired color temperature by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your preference, carry out the following procedure. 
(See page 22 for menu setting.) 
1.  Select COLOR TEMP. in the IMAGE menu. 
2.  Press the 
 or 
 button to select USER 
. 
3.  Press the ENTER button.
4.  Press the 

 or 
 button to select the desired item. 
5.  Press the 
 or 
 button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum adjustment results.
To cancel the menu:
7.  Press the MENU button. 
To enable the stored color temperature: 
1.  Set COLOR TEMP. to USER 
 in the IMAGE menu. 
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. White of which 
temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can 
change the color temperature using the following procedures. 
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
•  If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can't be 
obtained even when you maximize CONTRAST in the IMAGE menu. 
CONTRAST B 0
BRIGHTNESS R 0
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST G 0
BRIGHTNESS G 0
BRIGHTNESS B 0
Color Enhancer
You can set the user-defi ned balance between the brightness and hue using the menu. (See page 22 for menu 
setting.)
With the IMAGE menu:
1. Display the IMAGE menu.
2.  Select COLOR ENHANCER by pressing the 

 or 
 button.
3. Select USER
  by pressing the  or 
 button.
4.  Press the ENTER button.
5.  Select an item you want to set. 
GAMMA mode
Use this item to set the gamma optimally.
DYNAMIC
 ……Select when viewing images supplied from the computer.
NATURAL
 ……Select when viewing images supplied from the video device.
DETAIL
 ………Select when viewing images of which brightness should be kept relatively low, such as movies and 
music performance.
BrilliantColor
TM
Use this item to make the colors having medium brightness such as yellow and skin tone look natural. Press the  
button to decrease the value to lessen the effect. Press the 
 button to increase the value to heighten the effect.
(BrilliantColor™ doesn’t work at value 0.) 
 
6.  Select a setting value by pressing the  or 
 button. 
• You can adjust Color Enhancer also by pressing the CE button on the remote control. 
•  For more enhanced color reproduction, set BrilliantColorTM to 0. The white portion of the color wheel will be disa-
bled and you can reproduce true-to-life images.
With the remote control:
1.  Press the CE button on the remote control. 
  A window for color enhancer adjustment appears on the upper right of the screen. 
2. Press the 
 or 
 button to select USER .
3.  Press the ENTER button.
4. Press the 

 or 
 button to select GAMMA MODE or BrilliantColor™. 
5. Press the 
 or 
 button to adjust the selected item. 
AUTO COLOR
ENHANCER
BrilliantColorTM10 GAMMA MODE DYNAMIC
COLOR ENHANCER-USER
Adjusting projected images  (continued) 
						

							EN-27
ENGLISH
This projector automatically and properly projects video signals supplied from the computer. However, some video 
signals may not be projected, depending on the type of the computer. In such a case, press the AUTO POSITION 
button. (See page 16.) When the signal is still not projected properly, adjust the projected image using the SIGNAL 
menu. 
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ………………………… Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally.   ……… Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to the right. Every time 
the 
 button is pressed, the image moves to the left. 
The projected image is displaced vertically.   ………… Adjust VERT.POSITION in the SIGNAL menu. Every time the 
 
button is pressed, the image moves down. Every time the 
 
button is pressed, the image moves up. 
The top part of the image fl ags.  ……………………… Change the setting of HOLD in the SIGNAL menu. Select ON , 
press the ENTER button, and adjust BEGIN or END to minimize 
the fl agging.
Wide strips appear.  ……………………………………… Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - 
USER menu.
The motion doesn't run smoothly. ……………………… Adjust VERT. SYNC in the SIGNAL - USER menu.  Select 
AUTO for normal use. 
Noise appears on the right or left half of the image.
 …Adjust SHUTTER (LS) or SHUTTER (RS) in the SIGNAL - USER 
menu.
Noise appears on the top or bottom part of the image.
 …Adjust SHUTTER (U) or SHUTTER (L) in the SIGNAL - USER 
menu.
1.  Display the SIGNAL menu. 
2. Press the 

 or 
 button to select an item to adjust. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
•  Do not change the settings of the SIGNAL menu in normal use. 
Simple method to adjust the image position
To adjust the horizontal position: 
1.  Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the 
right edge of the image with the right side of the screen by adjusting TRACKING. 
2.  Repeat step 1 above to complete the adjustment of the horizontal position. 
To adjust the vertical position: 
3.  Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION. 
LPF 
You can select whether or not to enable the LPF. This item is set to OFF normally. 
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or 
game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected 
images become softened slightly. 
1.  Display the SIGNAL menu. 
2. Press the 

 or 
 button to select USER. 
3.  Press the ENTER button.
4. Press the 

 or 
 button to select LPF. 
5. Press the 
 or 
 button to choose ON or OFF. 
To cancel the menu:
6.  Press the MENU button. 
LPF OFF 
						

							EN-28
MENU ACCESSFEATURE
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
CONFIRM
O K CANCEL
MENU ACCESSFEATURE
XGA60opt.
LOCK
UNLOCKOK
OK
PASSWORD
O K CANCEL
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specifi ed users. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is entered. 
When the password is entered, the startup screen 
will switch to the regular operation screen.
MENU ACCESS ........... All the buttons except for the 
POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You can 
use this mode as a measure of prevention of wrong 
operation by children and restriction on operation 
by other than specifi ed users.
To enable the password function:
1.  Display the FEATURE menu.
2. Press the 

 or 
 button to select PASSWORD 
FUNCTION.
3. Press the  or  button to change the mode among 
DISPLAY INPUT
  and MENU ACCESS .
•  When there is a password already set, the pass-
word cancel menu is automatically selected. To 
set a new password, disable the password lock 
function. 
4.  Press the ENTER button.
•  The screen for setting the password function will 
appear. 
5.  Press the ENTER button.
•  The screen for entering a password will appear. 
6. Press the 

 or 
 button to select a number from 0 
to 9.
7. Press the 
 button.
•  You can set the next digit. 
8.  Repeat steps 6 and 7 to set a 4-digit password. 
9.  Enter the password again for confi rmation using the 
same steps.10. Select OK, and press the ENTER button. 
•  If the entered passwords don’t match, an error 
message will appear. 
•  To cancel the procedure, select CANCEL and 
press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. 
To cancel the password function: 
1.  Display the FEATURE menu.
2. Press the 

 or 
 button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for canceling the password function 
will appear.
4.  Press the ENTER button.
•  The screen for entering the password will 
appear. 
5. Press the 

 or 
 button to select a number from 0 
to 9.
6. Press the 
 button.
•  You can set the next digit. 
7.  Repeat steps 5 and 6 to enter the four-digit 
password. 
8. Press the 
 button, select OK, and press the 
ENTER button.
•  If you enter a wrong password, an error message 
will appear.
•  To cancel the procedure, press the 
 button, 
select CANCEL, and press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. 
Important:
•  Disable the password by pressing the MENU and 
ENTER buttons on the control panel at the same 
time.
Advanced features 
						

							EN-29
ENGLISH
Expand
By pressing the EXPAND button on the remote control, 
you can magnify the image to view the details.
Picture in Picture (PinP) 
One of the special features of this projector is the 
picture-in-picture (PinP) mode. The PinP mode allows 
you to view the images from  different sources at the 
same time. 
To use the PinP mode
1.  Press the PinP button on the remote control. 
•  When you press the PinP button with the image 
from the COMPUTER/COMPONENT VIDEO IN (1 
or 2) terminal displayed on the screen, the image 
from the VIDEO IN or S-VIDEO IN terminal is 
displayed as the sub image. 
•  When the image from the VIDEO IN or S-VIDEO 
IN terminal is displayed, the PinP mode isn't 
activated. 
2.  If necessary, select the desired external input 
source of the sub image by using the VIDEO or 
S-VIDEO button on the remote control or the VIDEO 
button on the control panel.
•  When the COMPUTER 1 or COMPUTER 2 
button on the remote control or the COMPUTER 
button on the control panel is pressed, the PinP 
mode will be canceled. 
3.  Press the PinP button on the remote control. 
•  The PinP mode will be canceled.
To change the position of the sub image:
Press the  or  buttons on the remote control.
•  When there is no video signal for sub image, you 
can’t change the display position.
Important:
•  In the PinP mode, you can’t make signal settings 
using the menu. 
•  The PinP mode is automatically disabled when the 
video signal for the main image is lost. 
•  The PinP mode isn't available with some input 
signals. For further information, see page 39. 
•  The size of the sub image varies depending on the 
input signal and settings. 
•  The PinP mode is available only when the ASPECT 
ratio is set to AUTO. 
•  In the PinP mode, the SHUTTER and OVER SCAN 
functions are disabled. 
Still
To stop the motion in the image temporarily (or to dis-
play a still image):
Press the STILL button on the remote control.
•  The image will freeze temporarily.
To resume the motion in the image:
Press the STILL button on the remote control again.
Important:
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen. To use the EXPAND mode:
1.  Press the EXPAND button.  
•  You can select the area to be magnifi ed by 
pressing the 
, , , or  button on the re-
mote control.
•  You can change the magnifi cation of the select-
ed area by pressing the + or - button.
2.  Press the EXPAND button again to exit the EXPAND 
mode.
•  The regular operation screen will appear.
Important:
•  In the EXPAND mode, you can't adjust the volume.
•  In the EXPAND mode, you can’t make signal set-
tings using the menu.
•  The EXPAND mode is available only with video sig-
nals from the COMPUTER IN (IN-1, IN-2 or  DVI-D) 
connector. It doesn’t work with video signals from 
the VIDEO IN and S-VIDEO IN connectors. 
•  The EXPAND mode doesn't function with some  
input signals. For details, see page 39.
•  In the EXPAND mode, the SHUTTER and OVER 
SCAN functions are disabled. 
EXPAND
Magnifi ed image 
						

							EN-30
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote 
control. 
Projector + computer with USB connector
Operation
•  You can use the mouse remote control function with a computer supporting USB only. 
•  When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case, 
restart the computer.
•  The mouse doesn’t function for a while after the power is turned on. 
Mouse pointer
Use to move the cursor on 
the image, instead of the 
computer mouse.
R-CLICK button
This operates in the same 
way as the right button on 
the computer mouse.Left click button
This operates in the same 
way as the left button on 
the computer mouse.  HOME button
Press to jump back 
to the fi rst page.
END button
Press to jump to the 
last page.PageUp button
Press to go back to 
the previous page.
PageDown button
Press to go to the 
next page.
Advanced features  (continued)
COMPUTER
VIDEO S-VIDEO
DVI-D(HDCP)
HOME Page Up
END Page DownAUTO POSITION
KEYSTONE
12
MENUENTER
LASER
R-CLICK
USBUSB cable
USB 4-pin
(type B)USB 4-pin
(type A)
to USB port