Mitsubishi Projector Xd2000u User Manual

							EN-11
ENGLISH
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit de-
signed for this projector. Ask a specialist for installation. 
For details, consult your dealer.
•  The warranty on this projector does not cover any 
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•  When using the projector mounted on the ceiling, 
set IMAGE REVERSE in the INSTALLATION menu to 
MIRROR INVERT. See page 23.
•  When the projector is mounted on the ceiling, im-
ages may appear darker than those projected in 
the case of tabletop mounting. This isn't a product 
malfunction.
•  Ask your installation specialist to provide a breaker.
  When you do not use the projector, be sure to shut 
down the main power by the breaker.
•  Do not install the projector where the exhaust vents 
are exposed to air emitted by an air conditioning.
  Such installation may cause a breakdown.
•  Do not install the projector near a fi re alarm because 
it emits hot air from its exhaust vents.
Rear projection
Ask a specialist for installation.  For details, consult 
your dealer.
•  For rear projection, set IMAGE REVERSE in the IN-
STALLATION menu to MIRROR. See page 23.
Caution:
•  Placing the projector directly on a carpet impairs 
ventilation by the fans, causing damage or failure. 
Put a hard board under the projector to facilitate 
ventilation. 
•  Place the projector at least 50 cm (or 20 inches) 
away from the wall to prevent the air inlet grille and 
the air outlet grilles that emit hot air from being 
blocked.  
•  Do not use the projector in the following locations 
and manners, which may cause fi re or electric 
shock.
•  In a dusty or humid place.
•  In a sideways or upside-down position.
• Near a heater.
•  In an oily, smoky, or damp place such as a kitchen.
• In direct sunlight.
•  Where the temperature rises high, such as in a 
closed car. 
•  Where the temperature is lower than +41ºF (or 
+5ºC) or higher than +104ºF (or +40ºC ).
Important:
•  We don’t recommend using the projector at an alti-
tude of 1500 meters or higher. Use at an altitude of 
1500 meters or higher may affect the projector’s life.  
						

							EN-12
Screen size and projection distance
Refer to the following table to determine the screen size. 
When the aspect ratio of the screen is 4:3
 Screen size  Projected distance (L)  Lens movable range
 4:3  Diagonal size   Height (H)   Width (W)  Min.   Max.   (H1)   (H2)   width (W1)
 inch  cm inch  cm inch  cm inch  m  inch  m  inch  cm inch  cm inch  cm
•  The above fi gures are approximate and may be slightly different from the actual measurements.
•  The lens movable range shows distances from the factory default position.
LENS SHIFT button
To adjust the positions of the projector and the screen, use LENS SHIFT button.
1.  Press the LENS SHIFT button. 
2. Press the 
, , or button to move the image position. 
Every time the  button is pressed, the image moves down.
Every time the 
 button is pressed, the image moves up.
Every time the  button is pressed, the image moves to the right. 
Every time the  button is pressed, the image moves to the left. 
•  When you hold down these buttons for 2 seconds or longer, the displayed image moves fast in the corresponding 
directions.
•  Be careful not to be caught in the opening in the lens while the lens is moving. 
Setting up your projector  (continued)
 40 102 24 61 32 81 54 1.4 74 1.9 12 30  2  6  3  8
 60 152 36  91  48 122 82  2.1 112 2.8  18  46  3  9  5  12
 80 203 48 122 64 163 110 2.8 150 3.8  24  61  4  11  6  16
 100 254 60 152 80 203 138 3.5 189 4.8  30  76  6  14  8  20
 150 381  90  229 120 305 208  5.3  284  7.2  45  114  8  21  12  30
 200 508 120 305 160 406 279  7.1  380  9.7  60  152  11  28  16  41
 250 635 150 381 200 508 349  8.9  476 12.1  75  191  14  36  20  51
 300 762 180 457 240 610 419 10.6 571 14.5  90  229  17  43  24  61
 L L
W1W1
H1 H2
H
W
 L L
W1W1
H1 H2
H
WFront projection Front projection, ceiling mounting 
						

							EN-13
ENGLISH
2 1
AUDIO OUTAUDIO IN
2 1
2 1
Viewing computer images
A. Connecting the projector to a computer
Preparation: 
•  Make sure that the power of the projector and that of the computer are turned off. 
•  When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-1 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER IN/COMPONENT VIDEO IN-1 terminal of the 
projector. 
2.  Connect the other end of the RGB cable to the monitor 
port of the computer.
•  When viewing images supplied from an analog-connected 
computer, press the COMPUTER button on the remote 
control. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-2 
terminal.)
1.  Connect one end of a commercially BNC cable to the 
COMPUTER IN/COMPONENT VIDEO IN-2 terminal of the 
projector. 
2.  Connect the other end of the BNC cable to the 5 BNC 
terminals of the monitor port of the computer.
For digital connection: 
1.  Connect one end of a commercially available DVI cable to 
the DVI-D (HDCP) terminal of the projector. 
2.  Connect the other end of the DVI cable to the DVI terminal 
of the computer. 
•  When viewing images supplied from a digital-connected 
computer, press the DVI-D(HDCP) button on the remote 
control. 
•  Turn on the main power switch of the projector before 
starting the computer. 
For audio connection: 
1.  Connect one end of a commercially available PC audio 
cable to the AUDIO IN-1/2 terminal of the projector. 
2.  Connect the other end of the PC audio cable to the audio 
output terminal of the computer.
•  This projector uses stereo pin jack for its audio input. Check 
the type of the audio output terminal of the connected 
computer and prepare a proper cable for connection. Some 
computers don't have the audio output terminal.
•  Speaker output is mono.
COMPUTER IN/COMPONENT 
VIDEO IN-1
DVI-D (HDCP)to monitor port
RGB cable
DVI cable to DVI
Computer
PC audio cable (option)
to audio output 
terminal
2 1
424); $2$**8 8
8 **8 $2
$); 424
COMPUTER IN/COMPONENT 
VIDEO IN-2
•  Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending 
on the type of the computer to be connected.
•  Use of a long cable may decrease the quality of projected images. 
•  Images may not be projected correctly, depending on the type of the connected computer. 
•  When DVI-D signal is input, some signal setting menus are unavailable. 
•  Also read the instruction manual of the equipment to be connected. 
•  Contact your dealer for details of connection.
to monitor port 
(5 BNC) 
						

							EN-14
2 1
1.  Plug the attached power cord into the power cord inlet of 
this projector.
2.  Plug the other end of the power cord into a power outlet.
•  The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
country. 
•  This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power 
plug. If the power plug doesn’t fi t your wall outlet, ask an electrician to change the wall outlet. 
•  The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply 
using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare 
an appropriate power cord separately.
•  Use 100-240 V AC 50/60 Hz to prevent fi re or electric shock.
•  Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to 
the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause 
fi re or electric shock. 
•  Do not modify or alter the power cord. If the power cord is modifi ed or altered, it may cause fi re or electric shock. 
Caution:
•  Plug in the power cord fi rmly. When unplugging, hold and pull the power plug, not the power cord.
•  Do not plug in or out the power cord with your hand wet. It may cause electric shock.
Earthing terminal
Power cord (Example)
Viewing computer images (continued)
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the 
COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal complies with the DDC2B standard. When a computer 
supporting this standard is connected to this terminal, the computer will automatically load the information from this 
projector and prepare for output of appropriate images. 
• 
When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector 
before starting the computer. 
1
MonitorFor monitor connection: 
1.  Connect one end of the RGB cable that is connected to the 
MONITOR OUT terminal of the projector.
For audio output connection: 
1.  Connect one end of a commercially available audio cable 
to the audio output terminal of the projector. 
2.  Connect the other end (white and red) of the audio cable to 
the audio output terminals (L, R) of the audio equipment.  
•  When the audio cable is connected to the AUDIO OUT ter-
minal, the speaker output is muted.
AUDIO OUT
2 1Audio cable (option)to audio input MONITOR OUT
Terminal cover
This projector includes a terminal cover. If necessary, install the terminal cover to the projector.
Install the terminal cover
1.  Fit two hooks of the terminal cover into the 
projector.
2.  Tighten the attachment screws (a) fi rmly.
• Don’t carry the projector by the terminal cover. 
(a)
RGB cable
B. Plugging the power cord 
						

							EN-15
ENGLISHPOWER
MENUENTERS TAT U S
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2.  Turn on the power of the connected computer. 
3.  Press the POWER button.
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•  Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the 
lens cap. 
• 
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a prod-
uct malfunction. 
•  Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated 
by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode 
changes from STANDARD to LOW about 1 minute after turn-on. 
•  The projector starts warming up when the POWER button is pressed. During the warm-up process, images 
may appear dark and no commands are accepted.
•  By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See page 34 and 37.) 
4.  Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
5. Adjust with the 
 or  button to get a fi ne picture. 
6.  Select an input source. 
•  Press the COMPUTER button on the projector or the COMPUTER1, COMPUTER2 or DVI-D(HDCP) button on 
the remote control that is corresponding to the terminal in use. 
•  The input source is switched from COMPUTER1 to COMPUTER2 to DVI at every press of the COMPUTER 
button on the projector. 
•  The projector automatically selects the appropriate signal format. The selected signal format is displayed on 
the screen.
•  The COMPUTER and VIDEO buttons don't function while the menu is being displayed. 
•  Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction. 
•  Images may not be projected in the correct position, depending on the type of the input signal. In such a case, 
press the AUTO POSITION button. (See page 16.)
•  When COMPUTER1 or COMPUTER2 is chosen as the source, images supplied from the computer may fl icker. 
Press the  or  button on the remote control to reduce fl icker, if it occurs.
7.  Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes. 
8.  Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.) 
•  When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
9.  Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the 
button again to display “ZOOM.”
10. Adjust with the 
 or  button to get an approximate size. 
11. Press the LENS SHIFT button. "LENS SHIFT" will appear on the display.
12.Press the 

 or 
 button to adjust the vertical position and 
 or  button to adjust the horizontal position of the 
displayed image.
Repeat steps 4, 5 and 9 to 12, if necessary. 
Important :
•  Focus, zoom and lens shift adjustment is possible in the normal picture mode only. In PinP or EXPAND mode, the 
adjustment is prohibited.
•  When you press the ZOOM/FOCUS button or LENS SHIFT button while no signal is supplied, a blue background 
screen is displayed.
•  When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars 
may appear on the 4:3 image screen. Consult your dealer in this case.
POWER button
COMPUTER button COMPUTER1, 2 buttons
DVI-D(HDCP) buttonPOWER button
ZOOM/FOCUS button
LENS SHIFT button
Main power switch 
						

							EN-16
POWER
MENUENTERSTATUS
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
Viewing computer images (continued)
To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to be turned off. 
•  During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp. 
16. Turn off the main power switch. 
•  The POWER indicator will go out. 
•  Cover the lens with the lens cap to protect it from dust.
•  For safety's sake, unplug the power cord from the outlet.
 
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the 
POWER button. 
•  Don’t shut down the projector while the STATUS indicator is blinking after the lamp lights up because the lamp’s 
life may be shortened. 
•  Don’t turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about 
10 minutes before turning the projector back on.) 
•  Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without 
closing the menu, the setting data of the menu may not be saved. 
•  If you shut down the projector while controlling the projector using the network function, the application software 
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM. 
AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1.  Display a bright image (such as a full-screen display of the Recycle Bin window). 
2.  When the screen saver has been enabled, disable it. 
3.  Press the AUTO POSITION button.  
  The projector automatically makes optimum positional settings for the input signal. 
•  If the image is not projected in the correct position even after you press the AUTO POSITION button several times, 
change the settings in the SIGNAL menu to put the image in the correct position. (See page 27.)
•  When you carry out this procedure with a dark image, the image may be displaced. 
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of 
the computer you use.) 
POWER buttonPOWER button
Main power switch 
						

							EN-17
ENGLISHConnecting to a video player, etc.
1.  Connect one end (yellow) of the supplied audio/video cable 
to the VIDEO IN terminal of the projector. 
2.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
3.  Connect the other end (yellow) of the audio/video cable to 
the video output terminal of the video equipment. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output terminals (L, R) of the video 
equipment. 
When the video equipment is equipped with the S-video 
output terminal, make the connection as follows. 
1.  Connect one end of a commercially available S-video cable 
to the S-VIDEO IN terminal of the projector. 
2.  Connect the other end of the S-video cable to the S-video 
output terminal of the video equipment. 
3.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output terminals (L, R) of the video 
equipment. 
When using the BNC connector:
(For VIDEO input)
•  When the video output terminal of the connected video 
equipment is BNC type, use the VIDEO IN terminal (BNC 
type). 
•  Select VIDEO as the input source. 
•  When using the VIDEO IN terminal (BNC type) and the 
VIDEO IN terminal (RCA type) at the same time, the video 
signal input to the VIDEO IN terminal (RCA type) takes 
priority. 
When using the BNC connector:
(For S-VIDEO input)
•  When the video output terminals of the connected video 
equipment are BNC (Y/C) type, connect Y and C to the 
S-VIDEO IN terminals (BNC type) respectively.  
•  Select S-VIDEO as the input source. 
•  When using the S-VIDEO IN terminals (BNC type) and the 
S-VIDEO IN terminal (S type) at the same time, the video 
signal input to the S-VIDEO IN terminal (S type) takes 
priority. 
•  When connecting a monophonic video device, use the white (L) terminal to connect the audio cable. (The same 
audio signal is output from the channels L and R of the AUDIO OUT terminal.) 
•  Also read the instruction manual of the equipment to be connected. 
•  Contact your dealer for details of connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of NO SIGNAL 
may appear on the screen when you change the channel via any channel that is not being received. In such a case, 
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip 
function (that is a function not to display channels that are not being received) enabled. 
Viewing video images
A. Connecting the projector to video equipment
Preparation:
•  Make sure that the power of the projector and that of the video equipment are turned off.
12
34
13
4
2To VIDEO 
IN terminalTo video 
output 
terminal Video player, or the like
To S-VIDEO 
IN terminal S-video cable
To S-video output 
terminalVideo player, or the likeAudio/video 
cable
To audio input 
terminal To audio 
output 
terminal
To audio input 
terminalAudio cable
(Option) To audio 
output 
terminal
To VIDEO IN 
terminal (BNC)BNC cableTo video 
output 
terminal Video player, or the like
To Y and C 
terminals 
(BNC)
BNC cable To S-video (Y/C) 
output terminalsVideo player, or the like 
						

							EN-18
CB(PB) Y CR(PR) 
B  G R 
AUDIO IN-2
BNC cable (Option)
DVD player or HDTV decoderBNC - RCA connector (option)COMPUTER IN/COMPONENT VIDEO IN-2
Connecting to video equipment having a DVI-D terminal
You can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a 
DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data 
that are output from DVD players. 
•  Use DVI cable for connection.
•  Select DVI as the input source. 
•  Only RGB signals are supported. Component video signals are not supported. 
•  HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital 
video data for the purpose of copy protection. 
•  When DVI-D signal is input, some signal setting menus are unavailable. 
 
When you connect this projector and a DVI-Digital device (such as a DVD player) via the DVI-D (HDCP) 
terminal, black color may appear dark and deep, depending on the type of the connected device. 
•  This depends on the black level setting of the connected device. There are 2 kinds of methods to digitally transfer 
image data, in which different black level settings are employed respectively. Therefore, the specifi cations of the 
signals output from DVD players differ, depending on the type of the digital data transfer method they use. 
•  Some DVD players are provided with a function to switch the methods to output DVI-Digital signals. When your 
DVD player is provided with such function, set it as follows.
  EXPAND or ENHANCED →
 NORMAL
•  See the users guide of your DVD player for details. 
•  When your digital device does not have such function, adjust the BRIGHTNESS to +16 and CONTRAST to -17 
in the IMAGE menu of this projector, or adjust the black color by viewing the image.
B. Plugging in the power cord
Plug the power cord in the same way as in the case of “Viewing computer images.” (See page 14.)
Viewing video images (continued)
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fi tting (Y, CB, CR). When connecting such DVD player with this 
projector, use the COMPUTER/COMPONENT VIDEO
 IN-2 terminals. 
•  The terminal's names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
•  The terminal's names vary depending on the connected devices. 
•  Use BNC cables for connection.
•  Image may not be projected correctly with some DVD players.
• 
If colors aren’t displayed correctly when the projector is connected to a high-defi nition video device having R, G, 
and B output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
Audio cable (option)
Audio output terminals
Equipment having a 
DVI-D terminalTo audio output 
terminalsAudio cable (Option)
To audio input 
terminals
To DVI-D terminal
DVI cable (Option)COMPUTER/COMPONENT 
VIDEO DVI-D (HDCP) 
						

							EN-19
ENGLISH
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2.  Turn on the power of the connected video equipment. 
3.  Press the POWER button.
•  It may take about 1 minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•  Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the 
lens cap. 
• 
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a prod-
uct malfunction. 
•  Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated 
by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode 
changes from STANDARD to LOW about 1 minute after turn-on. 
•  The projector starts warming up when the POWER button is pressed. During the warm-up process, images 
may appear dark and no commands are accepted.
•  By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See page 34 and 37.) 
4.  Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
5. Adjust with the 
 or  button to get a fi ne picture. 
6.  Select an input source. 
•  Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is 
corresponding to the terminal in use. 
•  The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector. 
• The VIDEO, S-VIDEO and COMPONENT buttons don't function while the menu is being displayed. 
•  Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction. 
•  Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)
•  When projecting images from a DVD player that is connected to the DVI connector, press the COMPUTER 
button on the projector to select DVI or press the DVI (HDCP) button on the remote control. 
•  When projecting images from a DVD player that is connected to the COMPUTER 1 or COMPUTER 2 connector, 
press the COMPUTER button on the projector or the COMPUTER 1 or COMPUTER 2 button on the remote 
control. 
7.  Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes. 
8.  Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.) 
•  When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
9.  Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the 
button again to display “ZOOM.”
10. Adjust with the 
 or  button to get an approximate size. 
11. Press the LENS SHIFT button. "LENS SHIFT" will appear on the display.
12.Press the 

 or 
 button to adjust the vertical position and 
 or  button to adjust the horizontal position of the 
displayed image.
Repeat steps 4, 5 and 9 to 12, if necessary. 
Important :
•  Focus, zoom and lens shift adjustment is possible in the normal picture mode only. In PinP or EXPAND mode, the 
adjustment is prohibited.
•  When you press the ZOOM/FOCUS button or LENS SHIFT button while no signal is supplied, a blue background 
screen is displayed.
POWER
MENUENTERSTATUS
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
Main power switchPOWER button
VIDEO button
COMPUTER button
ZOOM/FOCUS button
LENS SHIFT button COMPUTER1, 2 button
POWER button
DVI-D(HDCP) buttonS-VIDEO button
VIDEO button 
						

							EN-20 To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to be turned off. 
•  During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp. 
16. Turn off the main power switch. 
•  The POWER indicator will go out. 
•  Cover the lens with the lens cap to protect it from dust.
•  • For safety's sake, unplug the power cord from the outlet.
 
Instant Shut Down
You can turn off this projector just by turning off the power switch or unplugging the power cord without pressing the 
POWER button. 
•  Don’t shut down the projector while the STATUS indicator is blinking after the lamp lights up because the lamp’s 
life may be shortened. 
•  Don’t turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about 
10 minutes before turning the projector back on.) 
•  Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without 
closing the menu, the setting data of the menu may not be saved. 
•  If you shut down the projector while controlling the projector using the network function, the application software 
such as ProjectorView may fail. For details, see “User Guide of LAN Control Utility” contained in the CD-ROM. 
Volume from the speaker
Press the VOLUME + or - button to change the volume from the speaker.
The volume control bar will appear on the screen.
VOLUME     10
•  The volume control bar will disappear about 10 seconds after the VOLUME button is released.
•  The VOLUME buttons dont function while the menu selection bar or the menu is being displayed. 
•  When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from 
the speaker may be distorted.
AV mute
The video and audio signals are temporarily muted when the MUTE button is pressed. To cancel muting, press the 
MUTE button again.
• It takes several seconds before muting is completely canceled. 
Viewing video images (continued)
POWER
MENUENTERSTATUS
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
POWER buttonPOWER button
Main power switch